H3C S6800 Series Guide rapide

H3C S6800 & S6860 & S6861 Switches

PBB Configuration Examples

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New

H3C Technologies Co., Ltd.

Except for the trademarks of NewH3C Technologies Co., Ltd., any trademarks that may bementioned in this document are

the property of their respective owners.

The information in this document is subject to change without notice.

Contents

Introduction····································································································1

Prerequisites··································································································1

Example: Configuring PBB ············································································1

Network configuration ········································································································································1

Analysis······························································································································································1

Applicable hardware and software versions·······································································································2

Restrictions and guidelines································································································································2

Procedures·························································································································································2

Configuring BEB 1······································································································································2

Configuring BEB 2······································································································································3

Configuring BCB ········································································································································3

Configuring Device A ·································································································································3

Configuring Device B ·································································································································4

Verifying the configuration··································································································································4

Configuration files ··············································································································································4

Related documentation··················································································5

Introduction

This document provides PBB configuration examples.

Prerequisites

The configuration examples in this document were created and verified in a lab environment, and all

the devices were started with the factory default configuration. When you are working on a live

network, make sure you understand the potential impact of every command on your network.

This document assumes that you have basic knowledge of PBB.

Example: Configuring PBB

Network configuration

As shown in Figure 1, Site A and Site B both have VLANs 100 through 120.

•

Configure QinQ on Device Aand Device B to transmit VLANs 100 through 120 in SVLAN 1000.

•

Configure PBB on BEB 1 and BEB 2 to extend the VLANs across the two sites.

Figure 1 Network diagram

Analysis

To meet the network requirements, you must perform the following tasks on BEB 1 and BEB 2:

•

Configure a service instance on the downlink port to match frames that have an outer VLAN ID

of 1000.

•

Specify the access mode and data encapsulation type of the PBB VSI as Ethernet to retain the

VLAN tags of the customer frames.

XGE1/0/1 XGE1/0/2

PBBN

BEB 2

Device B

BCB

VLANs 100 to 120

Site 1

BVLAN 2000 BVLAN 2000

XGE1/0/1

XGE1/0/2

VLAN 1000

XGE1/0/1 XGE1/0/2

VLANs 100 to 120

Site 2

XGE1/0/1

XGE1/0/2

BEB 1

Device A

XGE1/0/1

XGE1/0/2

VLAN 1000

Applicable hardware and software versions

The following matrix shows the hardware and software versions to which this configuration example

is applicable:

Hardware

Software version

S6800 switch series

S6860 switch series Release 2702

S6861 switch series Not supported

Restrictions and guidelines

You need to configure PBB only on BEBs.

Procedures

Configuring BEB 1

# Create VLAN 1000 and VLAN 2000.

<BEB1> system-view

[BEB1] vlan 1000

[BEB1-vlan1000] quit

[BEB1] vlan 2000

[BEB1-vlan2000] quit

# Enable L2VPN.

[BEB1] l2vpn enable

# Create a VSI.

[BEB1] vsi test

# Assign PBB I-SID 1 to the VSI.

[BEB1-vsi-test] pbb i-sid 1

# Specify B-VLAN 2000 for the PBB VSI.

[BEB1-vsi-test-1] bvlan 2000

[BEB1-vsi-test-1] quit

[BEB1-vsi-test] quit

# Configure Ten-GigabitEthernet 1/0/1 as a trunk port, assign it to VLAN 2000, and remove it from

VLAN 1. Configure Ten-GigabitEthernet 1/0/1 as an uplink port of the PBB VSI.

[BEB1] interface ten-gigabitethernet 1/0/1

[BEB1-Ten-GigabitEthernet1/0/1] port link-type trunk

[BEB1-Ten-GigabitEthernet1/0/1] port trunk permit vlan 2000

[BEB1-Ten-GigabitEthernet1/0/1] undo port trunk permit vlan 1

[BEB1-Ten-GigabitEthernet1/0/1] pbb uplink vsi test

[BEB1-Ten-GigabitEthernet1/0/1] quit

# Configure Ten-GigabitEthernet 1/0/2 as a trunk port, assign it to VLAN 1000, and remove it from

VLAN 1.

[BEB1] interface ten-gigabitethernet 1/0/2

[BEB1-Ten-GigabitEthernet1/0/2] port link-type trunk

[BEB1-Ten-GigabitEthernet1/0/2] port trunk permit vlan 1000

[BEB1-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

# Create service instance 1 on Ten-GigabitEthernet 1/0/2.

[BEB1-Ten-GigabitEthernet1/0/2] service-instance 1

# Configure the service instance to match frames that have an outer VLAN ID of 1000. Associate the

service instance with the PBB VSI, and set the access mode to Ethernet.

[BEB1-Ten-GigabitEthernet1/0/2-srv1] encapsulation s-vid 1000

[BEB1-Ten-GigabitEthernet1/0/2-srv1] xconnect vsi test access-mode ethernet

[BEB1-Ten-GigabitEthernet1/0/2-srv1] quit

[BEB1-Ten-GigabitEthernet1/0/2] quit

# Enable Ethernet encapsulation for the PBB VSI.

[BEB1] vsi test

[BEB1-vsi-test] pbb i-sid 1

[BEB1-vsi-test-1] encapsulation ethernet

[BEB1-vsi-test-1] quit

[BEB1-vsi-test] quit

Configuring BEB 2

# Configure BEB 2 in the same way BEB 1 is configured. (Details not shown.)

Configuring BCB

# Create VLAN 2000.

<BCB> system-view

[BCB] vlan 2000

[BCB-vlan2000] quit

# Configure Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 as trunk ports, assign them to

VLAN 2000, and remove them from VLAN 1.

[BCB] interface range ten-gigabitethernet 1/0/1 to ten-gigabitethernet 1/0/2

[BCB-if-range] port link-type trunk

[BCB-if-range] port trunk permit vlan 2000

[BCB-if-range] undo port trunk permit vlan 1

[BCB-if-range] quit

Configuring Device A

# Create VLAN 1000.

<DeviceA> system-view

[DeviceA] vlan 1000

[DeviceA-vlan1000] quit

# Configure Ten-GigabitEthernet 1/0/1 as an access port, and assign it to VLAN 1000.

[DeviceA] interface ten-gigabitethernet 1/0/1

[DeviceA-Ten-GigabitEthernet1/0/1] port access vlan 1000

# Enable QinQ on Ten-GigabitEthernet 1/0/1.

[DeviceA-Ten-GigabitEthernet1/0/1] qinq enable

[DeviceA-Ten-GigabitEthernet1/0/1] quit

# Configure Ten-GigabitEthernet 1/0/2 as a trunk port, assign it to VLAN 1000, and remove it from

VLAN 1.

[DeviceA] interface ten-gigabitethernet 1/0/2

[DeviceA-Ten-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-Ten-GigabitEthernet1/0/2] port trunk permit vlan 1000

[DeviceA-Ten-GigabitEthernet1/0/2] undo port trunk permit vlan 1

[DeviceA-Ten-GigabitEthernet1/0/2] quit

Configuring Device B

# Configure Device B in the same way Device A is configured. (Details not shown.)

Verifying the configuration

# Verify that correct PBB VSI uplink connections have been established between BEB 1 and BEB 2.

<BEB1> display pbb connection

BMAC BVLAN Port Type Aging

011e-8300-0001 2000 XGE1/0/1 MC N

0cda-415e-232e 2000 XGE1/0/1 UC Y

<BEB2> display pbb connection

BMAC BVLAN Port Type Aging

011e-8300-0001 2000 XGE1/0/1MC N

00e0-fc58-1234 2000 XGE1/0/1UC Y

# Verify that hosts in Site 1 and Site 2 can ping each another. (Details not shown.)

# Verify that the BCB does not learn customer MAC addresses.

<BCB> display mac-address

Configuration files

•

BEB 1 and BEB 2:

vlan 1000

vlan 2000

l2vpn enable

vsi test

pbb i-sid 1

bvlan 2000

encapsulation ethernet

interface Ten-GigabitEthernet1/0/1

port link-mode bridge

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2000

pbb uplink vsi test

interface Ten-GigabitEthernet1/0/2

port link-mode bridge

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 1000

service-instance 1

encapsulation s-vid 1000

xconnect vsi test access-mode ethernet

•

BCB:

vlan 2000

interface Ten-GigabitEthernet1/0/1

port link-mode bridge

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2000

interface Ten-GigabitEthernet1/0/2

port link-mode bridge

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2000

•

Device A and Device B:

vlan 1000

interface Ten-GigabitEthernet1/0/1

port link-mode bridge

port access vlan 1000

qinq enable

interface Ten-GigabitEthernet1/0/2

port link-mode bridge

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 1000

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur