H3C S7500 Series Manuel utilisateur
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 1 Telnet Protection Configuration.................................................................................1-1
1.1 Introduction........................................................................................................................1-1
1.2 Telnet Protection Configuration.........................................................................................1-2
1.2.1 Configuring Telnet Protection..................................................................................1-2
1.2.2 Configuring SNMP Protection.................................................................................1-2
1.2.3 Configuring ICMP Protection...................................................................................1-2
1.2.4 Configuring Default-route Telnet Protection............................................................ 1-3
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-1
Chapter 1 Telnet Protection Configuration
When configuring Telnet protection, go to these sections for information you are
interested in:
zIntroduction
zTelnet Protection Configuration
1.1 Introduction
The Telnet protection function is used to protect Telnet packets, SNMP packets, and
ICMP packets from the specific source IP addresses in the case of attacks against the
network or high CPU utilization.
Telnet protection comes in global Telnet protection, special ARP Telnet protection, and
default-route Telnet protection. Global Telnet protection is the highest in priority; then
comes special ARPTelnet protection and default-route Telnet protection is the lowest in
priority.
After you configure global Telnet protection, all the Layer-3 interfaces are protected.
You can also configure special ARP Telnet protection to protect specified Layer-3
interfaces. If the default route exists, you can enable special ARP Telnet protection on
the gateway of the network segment where the next hop of the default route resides
through enabling default-route Telnet protection. By default, default-route Telnet
protection is disabled.
Before configuring Telnet protection, you need to enable Telnet, SNMP, and ICMP
protection respectively. You can configure Telnet protection, SNMP protection, and
ICMP protection for only the packets of the specific source IP addresses.
Caution:
After the network address translation (NAT) function is enabled,
zYou cannot configure global Telnet protection.
zYou cannot configure special ARP Telnet protection for the Layer-3 interface where
NAT resides.
zYou cannot configure default-route Telnet protection.
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-2
1.2 Telnet Protection Configuration
1.2.1 Configuring Telnet Protection
Follow these steps to configure Telnet protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable Telnet
protection
attack-protection telnet
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match
this source IP address only.
Enable global
Telnet protection
or special ARP
Telnet protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.2 Configuring SNMP Protection
Follow these steps to configure SNMP protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable SNMP
protection
attack-protection
snmp [ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match this
source IP address only.
Enable global Telnet
protection or special
ARP Telnet
protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.3 Configuring ICMP Protection
Follow these steps to configure ICMP protection:
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-3
To do... Use the command... Remarks
Enter system view system-view —
Enable ICMP
protection
attack-protection
icmp [ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match
this source IP address only.
Enable global Telnet
protection or special
ARP Telnet
protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.4 Configuring Default-route Telnet Protection
Follow these steps to configure default-route Telnet protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable default-route
Telnet protection
undo attack-protection
disable-defaultroute
Required
By default, default-route
Telnet protection is
disabled.
Autres manuels pour S7500 Series
29
Autres manuels H3C Changer
H3C
H3C S12500 Series Manuel utilisateur
H3C
H3C S5560S Series Mode d’emploi
H3C
H3C S12500X-AF Series Manuel utilisateur
H3C
H3C S6890 Series Guide rapide
H3C
H3C S3100-52P Instructions d'installation
H3C
H3C S5820V2-48S Guide de l'utilisateur
H3C
H3C S5120-HI Series Manuel utilisateur
H3C
H3C S9500 Series Instructions d'installation
H3C
H3C S5130S-EI series Manuel utilisateur
H3C
H3C s5800 series Manuel utilisateur
H3C
H3C LSW1SP4P0 Manuel utilisateur
H3C
H3C S9500 Series Manuel utilisateur
H3C
H3C S7500E-XS Series Manuel utilisateur
H3C
H3C S9825 Series Manuel utilisateur
H3C
H3C S5560S-EI Series Manuel utilisateur
H3C
H3C S6116 Series Manuel utilisateur
H3C
H3C s5820x series Manuel d'installation
H3C
H3C S9500 Series Manuel utilisateur
H3C
H3C S7500 Series Manuel utilisateur
H3C
H3C S9500E Series Manuel utilisateur
