H3C SecPath M9000 Series Manuel utilisateur

Manual version: APW100-20200316 BOM: 3123A1Y9

H3C SecPath M9000 NSQM1FAB08E0 switching

fabric module

1 Identifier

The module identifier NSQM1FAB08E0 is on the far left of the front panel.

2 About the module

The NSQM1FAB08E0 switching fabric module provides one console port.

3 Specifications

Figure 1 Front panel

(1) Console port (CONSOLE) (2) Status LEDs

(3) Captive screw (4) Ejector lever

Table 1 Module specifications

Item Specification

Dimensions (H × W × D) 40 × 426 × 298 mm (1.57 × 16.77 × 11.73 in)

Power consumption 101 W to 135 W

Weight 2.77 kg (6.11 lb)

Hot swapping Supported

Connector type RJ-45

Port 1 × console port

Ambient temperature •Operating: 0°C to 45°C (32°F to 113°F)

•Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity •Operating: 5% RH to 95% RH, noncondensing

•Storage: 5% RH to 95% RH, noncondensing

Compatible device model and slot M9016-V gateway (slots 10 to 13)

Manual version: APW100-20200316 BOM: 3123A1Y9

IMPORTANT:

An M9016-V gateway requires a minimum of three switching fabric modules, and slots 10 and 11

must be installed with switching fabric modules.

4 LEDs

The module provides LEDs to show its operating status.

Table 2 LED description

LED Status Description

Status LEDs

RUN ALM

Flashing (0.5 Hz) Off The switching fabric module is operating properly.

Off On The switching fabric module is faulty.

Flashing (0.5 Hz) On The temperature of the switching fabric module has

exceeded the upper or lower limit.

Off Off The switching fabric module has not started.

On Off The switching fabric module is starting up.

5 Installing and removing the module

CAUTION:

Wear a reliably grounded ESD wrist strap when installing and removing the module.

5.1 Installing the module

1. Face the rear panel of the device.

2. Remove the filler panel from the target slot.

This example installs the module in slot 10 on an M9016-V gateway.

3. Place the module horizontally with the component side facing up. Fully open the ejector levers

of the module and then gently push the module into the slot along the guide rails.

4. Continue to push the module on the middle part of the front panel until the ejector levels touch

the slot edges.

Manual version: APW100-20200316 BOM: 3123A1Y9

iii

Figure 2 Aligning and inserting the module into the slot

5. Close the ejector levers. Make sure the module is in close contact with the backplane.

Figure 3 Closing the ejector levers

6. Use a Phillips screwdriver to fasten the captive screws on the module.

5.2 Removing the module

1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is

released.

2. Simultaneously open the ejector levers on the module to separate the module from the

backplane, and then pull the module slowly out of the chassis along the guide rails.

Manual version: APW100-20200316 BOM: 3123A1Y9

3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component

side facing up.

If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure

good ventilation in the device.

The information in this document is subject to change without notice.

Autres manuels pour SecPath M9000 Series

Ce manuel convient aux modèles suivants

Autres manuels H3C Porte

H3C

H3C MSR3610-X1 Guide de l'utilisateur

H3C

H3C SecPath M9000 Series Manuel utilisateur

H3C

H3C VG Series Feuille d'instructions

H3C

H3C VG Series Manuel utilisateur

H3C

H3C MSR3610-X1 Manuel utilisateur

H3C

H3C VG Series Feuille d'instructions

H3C

H3C MSR3610-I Series Manuel utilisateur

H3C

H3C SecPath M9000-AI Manuel utilisateur

H3C

H3C MSR3610-I iMC EAD Guide de référence rapide

H3C

H3C VG Series Manuel utilisateur

H3C

H3C VG 21-08 Manuel utilisateur

H3C

H3C SecPath V100-E Manuel utilisateur

H3C

H3C SR6602-I AI Series Manuel d'utilisation et d'entretien

H3C

H3C MSR2600-10-X1 Manuel utilisateur

H3C

H3C VG 20-16 Mode d’emploi

H3C

H3C VG 10-40 Manuel utilisateur

H3C

H3C SecPath M9000-AI-E8 Manuel utilisateur

H3C

H3C MSR2600-6-X1 Manuel utilisateur

H3C

H3C SecPath M9000 Series Mode d’emploi

H3C

H3C ICG2000 Manuel utilisateur

H3C

H3C SecPath V100-S Manuel utilisateur

H3C

H3C SR6602-I AI Series Manuel utilisateur

H3C

H3C VG 80-20 Mode d’emploi

H3C

H3C ICG2000 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur