H3C LSPM6QP2PS Manuel utilisateur

H3C LSPM6QP2PS interface card user

manual-6PW101

Introduction

Overview

The LSPM6QP2PS interface card provides two 20G QSFP+ ports.

Figure 1 LSPM6QP2PS interface card

(1) QSFP+ port LED (2) QSFP+ port

(3) Captive screw (4) Ejector lever

NOTE:

The switch models that the interface card is applicable to may change

over time. For the most recent list of applicable switch models, contact

H3C Support or marketing staff.

QSFP+ ports

You can install QSFP+ DAC cables in Table 1 in the QSFP+ ports on the

interface card.

Table 1 QSFP+ DAC cables available for the QSFP+ ports

QSFP+ DAC cable

Cable length Data rate

LSWM1QSTK0 1 m (3.28 ft)

40 Gbps

LSWM1QSTK1 3 m (9.84 ft)

LSWM1QSTK2 5 m (16.40 ft)

The QSFP+ DAC cables have a maximum transmission rate of 40 Gbps.

When you connect the QSFP+ DAC cables to the QSFP+ ports on the

LSPM6QP2PS interface card, the cables provide a maximum

transmission rate of 20 Gbps.

NOTE:

H3C recommends that you use H3C QSFP+ DAC cables for the

QSFP+ ports on the interface card. The QSFP+ DAC cables available

for the interface card are subject to change over time. For the most

recent list of QSFP+ DAC cables available for the interface card,

contact H3C Support or marketing staff.

LEDs

Table 2 describes the LEDs for the QSFP+ ports on the card panel..

Table 2 QSFP+ port LED description

LED status Description

Steady green The port is operating at 20 Gbps, and a link is

present on the port.

Flashing green The port is sending or receiving data at 20 Gbps.

Off No QSFP+ DAC cable is installed in the port, or

no link is present on the port.

NOTE:

The QSFP+ port LEDs are not affected by the port mode switching

button on your switch. For more information about the port mode

switching button, see the installation guide of the switch.

Installing and removing the interface card

CAUTION:

•Before you install or remove an interface card, wear an ESD wrist

strap and make sure the wrist strap makes good skin contact and is

reliably grounded.

•To avoid device damage, do not use excessive force when you

install or remove an interface card.

Prepare the following tools before you install or remove an interface

card:

•Phillips screwdriver.

•Flat blade screwdriver.

•ESD wrist strap.

The installation tools are not provided with H3C devices. Prepare them

yourself.

Installing the interface card

This guide uses the S5130-30C-HI switch as an example.

To install the interface card:

1. Use the Phillips screwdriver to remove the screw on the filler panel in

the target interface card slot, as shown by callout 1 in Figure 2.

Keep the removed screw secure for future use.

2. Insert the flat blade screwdriver through the handle on the filler

panel to pull out the filler panel, as shown by callout 2 in Figure 2.

Keep the removed filler panel secure for future use.

3. Unpack the interface card.

4. Insert the interface card slowly into the slot along the guide rails, as

shown by callout 1 in Figure 3.

5. Rotate inward the ejector lever on the card as shown by callout 2

in Figure 3 until the interface card is in close contact with the switch.

6. Use the Phillips screwdriver to tighten the captive screw on the

interface card as shown by callout 3 in Figure 3.

Figure 2 Removing a filler panel

Figure 3 Installing the interface card

Removing the interface card

CAUTION:

•Before you remove the interface card, remove the cable from it.

•If you are not to install a new interface card after removin

the old

one, install a filler panel in the empty interface card slot. This

prevents dust from entering the switch and maintains good

ventilation in the switch.

To remove an interface card:

1. Prepare an anti-static bag.

2. Use the Phillips screwdriver to loosen the captive screw on the

interface card, as shown by callout 1 in Figure 4.

3. Rotate outward the ejector lever as shown by callout 2 in Figure 4.

4. Pull out the interface card slowly out the interface card slot as shown

by callout 3 in Figure 4.

5. Place the removed interface card in the anti-static bag.

Figure 4 Removing the interface card

Installing and removing QSFP+ DAC cables

For information about installing or removing QSFP+ DAC cables, see

H3C QSFP+ Transceiver Modules and DAC/AOC Cables Installation

Guide at www.h3c.com.

Verifying the installation

After the installation is complete, identify whether the interface card is

operating correctly.

If the interface card is not operating correctly, perform the following

steps:

1. Reinstall it following the installation procedure described in this

document.

2. If the problem persists, contact H3C Support.

Technical support

New H3C Technologies Co., Ltd. provides customers with

comprehensive technical support and service. If you purchase the

products from the sales agent of New H3C Technologies Co., Ltd.,

please contact our sales agent or technical personnel.

Website: http://www.h3c.com.hk

E-mail: service@h3c.com

BOM: 3101A 0K4

Table des matières

Autres manuels H3C Matériel informatique

H3C

H3C LSXM1SFF08B1 Mode d’emploi

H3C

H3C LSWM124TG2H Manuel utilisateur

H3C

H3C FAN-40-5-A Manuel utilisateur

H3C

H3C SecPath M9000 NSQM1ADEDFGA0 Mode d’emploi

H3C

H3C LSWM124XG2QFC Manuel utilisateur

H3C

H3C SecPath F5000-A5 NSQ1MPUA0 Manuel utilisateur

H3C

H3C NIC-FC730i-Mb-2-32G Manuel utilisateur

H3C

H3C LSWM116FC Manuel utilisateur

H3C

H3C LSWM116Q Manuel utilisateur

H3C

H3C H3C S7500E-X Manuel utilisateur

H3C

H3C LSXM112XFANH Manuel utilisateur

H3C

H3C LSXM1SFF16C1 Mode d’emploi

H3C

H3C LSXM108CFAN Manuel utilisateur

H3C

H3C SecPath FAN-120B-2-A16 Manuel utilisateur

H3C

H3C LSPM6G4T6 Manuel utilisateur

H3C

H3C LSVM1FANSC Manuel utilisateur

H3C

H3C LSPM1FAN Manuel utilisateur

H3C

H3C BT1004E Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur