Gude Expert Net Control 2302 Manuel utilisateur

Manual

Expert Net Control 2302

Manual Ver. 1.3.0

from Firmware Ver. 1.3

Table of contents

1. Device Description 5

1.1 Security Advice ....................................................................................................... 6

1.2 Content of Delivery ................................................................................................. 6

1.3 Description ............................................................................................................. 6

1.4 Installation ............................................................................................................. 7

1.4.1 Connection Example ................................................................................................ 8

1.5 Technical Specifications ........................................................................................ 10

1.6 Sensor .................................................................................................................. 10

2. Operating 13

2.1 Operating the device directly ................................................................................ 14

2.2 Control Panel ........................................................................................................ 15

2.3 Maintenance ........................................................................................................ 16

2.3.1 Maintenance Page ................................................................................................. 18

2.3.2 Configuration Management .................................................................................. 20

2.3.3 Bootloader Activation ............................................................................................ 21

3. Configuration 23

3.1 Output Ports ......................................................................................................... 24

3.1.1 Watchdog ............................................................................................................... 25

3.2 Input Ports ............................................................................................................ 27

3.3 Ethernet ............................................................................................................... 28

3.3.1 IP Address ............................................................................................................... 28

3.3.2 IP ACL ..................................................................................................................... 29

3.3.3 HTTP ....................................................................................................................... 31

3.4 Protocols .............................................................................................................. 32

3.4.1 Console ................................................................................................................... 32

3.4.2 Syslog ..................................................................................................................... 34

3.4.3 SNMP ...................................................................................................................... 34

3.4.4 Radius ..................................................................................................................... 36

3.4.5 Modbus TCP ........................................................................................................... 37

3.4.6 MQTT ...................................................................................................................... 38

3.5 Clock ..................................................................................................................... 39

3.5.1 NTP ......................................................................................................................... 39

3.5.2 Timer ...................................................................................................................... 40

3.5.3 Timer Configuration ............................................................................................... 40

3.6 Sensors ................................................................................................................. 47

3.6.1 Port Switching ........................................................................................................ 48

3.7 E-Mail ................................................................................................................... 49

3.8 Front Panel ........................................................................................................... 50

Table of contents

4. Specifications 51

4.1 Automated Access ................................................................................................ 52

4.2 Messages .............................................................................................................. 52

4.3 IP ACL ................................................................................................................... 54

4.4 IPv6 ...................................................................................................................... 55

4.5 Radius ................................................................................................................... 55

4.6 SNMP ................................................................................................................... 56

4.6.1 Device MIB 2302 .................................................................................................... 58

4.7 SSL ........................................................................................................................ 59

4.8 Console ................................................................................................................. 61

4.8.1 SSH ......................................................................................................................... 65

4.8.2 Console Cmd 2302 ................................................................................................. 65

4.9 Modbus TCP ......................................................................................................... 73

4.10 MQTT ................................................................................................................... 78

4.10.1 Example HiveMQ .................................................................................................... 80

5. Support 82

5.1 Data Security ........................................................................................................ 83

5.2 Contact ................................................................................................................. 83

5.3 Declaration of Conformity ..................................................................................... 84

5.4 FAQ ...................................................................................................................... 84

Index

Device Description

1 Device Description

1.1 Security Advice

·The device must be installed only by qualified personnel according to the following

installation and operating instructions.

·The manufacturer does not accept responsibility in case of improper use of the

device and particularly any use of equipment that may cause personal injury or ma-

terial damage.

·The device contains no user-maintainable parts. All maintenance has to be per-

formed by factory trained service personnel.

·Connect the device to the mains (230V AC) or to an AC Adaptor (10V to 24V AC,

12V to 28V DC, at 4 watts of power). Under no circumstances should the unit be fed

with the mains and the AC Adaptor at the same time!

·The device is intended for indoor use only. Do NOT install them in an area where ex-

cessive moisture or heat is present.

·Because of safety and approval issues it is not allowed to modify the device without

our permission.

·The device is NOT a toy. It has to be used or stored out or range of children.

·Care about packaging material. Plastics has to be stored out of range of children.

Please recycle the packaging materials.

·In case of further questions, about installation, operation or usage of the device,

which are not clear after reading the manual, please do not hesitate to ask our sup-

port team.

1.2 Content of Delivery

The package includes:

·Expert Net Control 2302

·Quick Start Guide

1.3 Description

The Expert Net Control 2302 can switch 4 different relay outputs and monitor 8 pass-

ive signal inputs. The device has the following features:

·4 switchable, potential-free relay outputs, switching voltage 230 V AC 16 A / 24 V

DC, 10 A

·Relays dispose of high contact reliability also at very small loads

·8 passive inputs for monitoring NO and NC devices, e.g. door contacts, smoke de-

tectors etc.

·Stop input to switch-off of all relays

·Operation with 230 V AC or 24 V DC voltage

·Optional sensor for environmental monitoring (temperature, humidity and air pres-

sure)

·Console commands via SSH, Telnet and serial interface

·SSH support with public key and passwords

·Individually parameterisable switch-on delay of all outputs

Device Description

·Programmable timetables and turn-on/turn-off sequences

·Individually adjustable watchdog for each output, which switches depending on ac-

cessibility (network ping)

·Dual TCP/IP stack with IPv4 and IPv6 support (IPv6-ready)

·Control and monitoring of the device via Ethernet with an integrated web server with

SSL encryption (TLS 1.1, 1.2, 1.3)

·Control and configuration with CGI parameters and JSON messages via HTTP

(REST API)

·SNMP (v1, v2c and v3, traps)

·MQTT 3.1.1 Support

·Modbus TCP support

·Radius support

·Generation of messages (e-mail, syslog and SNMP traps) and switching of relays

depending on sensor measurement limits

·Firmware update during operation via Ethernet possible

·Encrypted e-mails (SSL, STARTTLS)

·Access protection through IP access control

·Low own consumption

·Developed and produced in Germany

1.4 Installation

1. 230V AC power supply

2. Four relay outputs ( potential-free)

3. Ethernet connector (RJ45)

4. Sensor connector (RJ45)

Device Description

5. Activity LED (Input) for digital inputs

6. 4 status LED for relay outputs

7. Status LED

8. Button for Select and OK

9. Alternative low power supply LV PWR (Low Voltage PoWeR)

10. Eight passive inputs (with GND ( ) for 2 inputs each)

11. Stop input (with GND ( )) to switch-off of all relais

Start-up the device

·Connect the device to the mains (230V AC) or to an AC Adaptor (10V to 24V AC,

12V to 28V DC, at 4 watts of power). Under no circumstances should the unit be fed

with the mains and the AC Adaptor at the same time!

·Plug the network cable into the Ethernet socket (RJ45) .

·Connect the relay to the loads that should be be operated.

·Make contact between the lines to be monitored and the digital inputs. To close an

input circuit there has to be a connection between a ground pin ( ) and the respect-

ive input pin has to be made.

·Connect the sensor (if any) to the device.

1.4.1 Connection Example

Here an example of a block diagram in which the device is supplied with 230V AC, and

four AC loads (L1 - L4) are connected. In addition, the inputs are joined to eight

switches (S1 - S8), and the stop input is connected to the push-button PB1.

Device Description

As an alternative to connecting "In 1-8" and "GND", voltages can also be fed in

between "In 1-8" and GND. The maximum input voltage is 24V, voltages below 3V are

detected as LOW state, and voltages above 8V are detected as HI.

Device Description

1.5 Technical Specifications

Interfaces

1 x Ethernet port (RJ45)

1 x Connector for mains supply (230V AC)

1 x Connector for AC Adaptor (12V DC, 0,5A). 12V DC power

supply

12 x screw terminal with 8 inputs and 4 x GND

8 x screw terminal with 4 make contacts (230V AC 16A,

24V DC 10 A)

1 x RJ45 for external sensor

Network connectivity

10/100 MBit/s 10baseT Ethernet

Power Supply

internal power supply (230V AC)

alternative: 10V to 24V AC, 12V to 28V DC (at 4 watts of

power)

Environment

·Operating temperature

·Storage temperature

·Humidity

0°C to 50°C

-15°C to 60°C

10% to 85%

Case

plastics black

Measurements

105mm x 70mm x 90mm (L x H x D)

Weight

approx. 300g

1.6 Sensor

One external sensor can be connected to the Expert Net Control 2302. The following

sensors are currently available

Humidity/Temperature Sensor 7102 (End-of-Life)

Cable length

Connector

RJ45

temperature range

-20°C to +80°C, ±0,5°C (maximum) and ±0,3°C (typical)

air humidity range

(non-condensing))

0-100%, ±3% (maximum) and ±2% (typical)

Table des matières

Autres manuels Gude Système d'E/S

Gude

Gude Expert Net Control 2312 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur