Grizzly H8091 Manuel utilisateur
MODEL H8091
31/2 Ton Quick Pump
Garage Jack
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JC8822 PRINTED IN CHINA
Specifications
Maximum Lifting Capacity .....................7000 lbs.
Lifting Range .......................................43⁄4"–145⁄8"
Weight .......................................................83 lbs.
Figure 1. Model H8091 Identification.
Figure 2. Pump pedal and release valve gear.
Foot
Pedal Saddle
If you need help with the Model H8091, call our
Technical Support line at: (570) 546-9663.
Foot
Pedal
Machine
Label
Jack Handle
Failure to follow these instructions could
result in serious personal injury or death:
To raise the saddle gradually:
Turn the jack handle clockwise as far as it will
turn and pump the handle up and down. Turning
the handle clockwise will close the release valve
(see Figure 2).
To raise the saddle quickly:
With the jack handle turned fully clockwise, push
the foot pedal down and release it slowly. Each
pump of the pedal will raise the saddle approxi-
mately one-third of its full range.
To lower the saddle:
Slowly turn the jack handle counterclockwise.
Operation
Release
Valve Gear
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle with
appropriately rated support stands
before working under it.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Maintenance
Keep the hydraulic rams clean and free of any
dust, dirt, or foreign debris. Abrasive material
stuck to the ram can damage the hydraulic seal
when the ram is retracted back into the jack.
Regularly wipe the hydraulic rams clean with a
lightly oiled rag.
The Model H8091 will require hydraulic fluid after
long-term use. This will be noticeable if the jack
will not reach its maximum height when pumped.
Only use a high quality hydraulic fluid.
To add hydraulic fluid:
1. Completely lower the jack.
2. Remove the fill plug shown in Figure 3.
Bleeding the Air
If the jack becomes spongy or will not rise when
pumped, then air bubbles may be in the hydraulic
system. These air bubbles must be 'bled' from
the hydraulic fluid before the jack can be safely
operated.
To remove the air bubbles:
1. Remove the fill plug.
2. Rotate the handle counterclockwise until it
stops.
3. Pump the jack handle rapidly to force the air
bubbles out through the fill hole. When the air
bubbles and fluid stop coming out, put the fill
plug back.
4. Repeat Step 3 as many times as needed until
the air bubbles stop coming out in the hydrau-
lic fluid.
3. Add fluid until it reaches the top of the fill plug
hole.
4. Replace the fill plug.
5. Test the operation of the jack by pumping
it up to the maximum height and applying a
load to the saddle. The jack should hold the
weight of the load without a sinking or spongy
feeling.
—If the jack did not perform properly, then
air may need to be bled from the pump
system.
Figure 3. Fill plug.
Fill Plug
H8091 Main Parts Breakdown
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PR09M EXT RETAINING RING 20MM 23 PH8091014 HEX NUT M16-1.75
2 PW13M FLAT WASHER 20MM 24 PH8091024 LINKING SHAFT
3 PH8091003 FRONT WHEEL 25 PH8091025 SPECIAL BOLT (LEFT)
4 PH8091004 SADDLE 26 PH8091026 PUMP CORE PIN
5 PH8091005 SADDLE BASE 27 PH8091027 HANDLE SOCKET
6 PH8091006 SADDLE BASE AXIS 28 PH8091028 HANDLE SOCKET SCREW
7 PR06M EXT RETAINING RING 16MM 29 PH8091029 LINKING BLOCK
8 PH8091008 LINK ROD 30 PH8091030 COTTER PIN 4 X 47MM
9 PH8091009 LINKING BOLT 31 PH8091031 PULL SPRING
10 PH8091010 SIDE FRAME 32 PH8091032 PEDAL BASE
11 PLW04M LOCK WASHER 8MM 33 PH8091033 GEAR
12 PN03M HEX NUT M8-1.25 34 PH8091034 CYLINDER ASSEMBLY
13 PLW10M LOCK WASHER 16MM 35 PH8091035 HANDLE
14 PH8091014 HEX NUT M16-1.75 36 PH8091036 RATCHET AXIS
15 PH8091015 REAR WHEEL ASSEMBLY 37 PW08M FLAT WASHER 16MM
16 PR11M EXT RETAINING RING 25MM 38 PH8091038 FLAT RATCHET
17 PLW05M LOCK WASHER 12MM 39 PLW06M LOCK WASHER 10MM
18 PB25M HEX BOLT M12-1.75 X 25 40 PN08M HEX NUT M10-1.25
19 PH8091019 LIFTING ARM 41 PW01M FLAT WASHER 8MM
20 PH8091020 SPECIAL BOLT (RIGHT) 42 PH8091042 COTTER PIN 2MM X 12MM
21 PLW12M LOCK WASHER 18MM 43 PH8091043 MACHINE LABEL
22 PH8091022 TORSION SPRING
The machine label warns about hazards and ways to prevent injury. The owner of the jack MUST
maintain the original location and readability of the label. If the label is removed or becomes
unreadable, contact Grizzly at (800) 523-4777 or www.grizzly.com to order a new label.
H8091 Hydraulic Pump Parts Breakdown
REF PART # DESCRIPTION REF PART # DESCRIPTION
101 PH8091101 RAM ROD 118 PH8091118 BALL
102 PH8091102 RAM HEAD 119 PH8091119 SEAL WASHER
103 PH8091103 RAM HEAD PIN 120 PH8091120 PLUG SCREW
104 PH8091104 O-RING 121 PH8091121 OVERLOAD VALVE SCREW
105 PH8091105 TANK NUT 122 PH8091122 WASHER
106 PH8091106 O-RING 123 PH8091123 WIPER
107 PH8091107 CYLINDER 124 PH8091124 BACK-UP RING
108 PH8091108 RESERVOIR 125 PH8091125 O-RING
109 PH8091109 OIL FILL PLUG 126 PH8091126 VALVE BLOCK
110 PH8091110 O-RING RETAINER 127 PH8091127 LEFT PLUNGER
111 PH8091111 O-RING 128 PH8091128 BALL - BOTTOM
112 PH8091112 O-RING 129 PH8091129 BALL - TOP
113 PH8091113 GEAR RETAINING NUT 130 PH8091130 PLUG SCREW
114 PH8091114 O-RING 131 PH8091131 BALL
115 PH8091115 RELEASE VALVE ASSEMBLY 132 PH8091132 RIGHT PLUNGER
116 PH8091116 ACTUATOR 133 PH8091133 SPRING
117 PH8091117 GUIDE PLATE
Table des matières
Autres manuels Grizzly Outils électriques
Grizzly
Grizzly T23108 Manuel utilisateur
Grizzly
Grizzly G0610 Guide de démarrage rapide
Grizzly
Grizzly T32253 Manuel utilisateur
Grizzly
Grizzly G1035 Manuel utilisateur
Grizzly
Grizzly G0543 Manuel utilisateur
Grizzly
Grizzly G8689 Manuel utilisateur
Grizzly
Grizzly G0500 Manuel utilisateur
Grizzly
Grizzly T10051 Manuel utilisateur
Grizzly
Grizzly G0925 Manuel utilisateur
Grizzly
Grizzly G0500 Manuel utilisateur
Grizzly
Grizzly T27978 Manuel utilisateur
Grizzly
Grizzly G8693 Manuel utilisateur
Grizzly
Grizzly Power Feeder G4176 Manuel utilisateur
Grizzly
Grizzly T1242 Manuel utilisateur
Grizzly
Grizzly T1244 Manuel utilisateur
Grizzly
Grizzly FOOT SHEAR T23036 Manuel utilisateur
Grizzly
Grizzly G8689 Manuel utilisateur
Grizzly
Grizzly G8622 Manuel utilisateur
Grizzly
Grizzly Vertical Mill G0667X Manuel utilisateur
Grizzly
Grizzly G0612 Guide de démarrage rapide
