Greenlee 1981 Manuel utilisateur
INSTRUCTION MANUAL
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com
99925150 REV 3 © 2016 Greenlee Textron Inc. 7/16
19 81
Mechanical
Crimping Tool
1981 Mechanical Crimping Tool
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
All specications are nominal and may change as design
improvements occur. Greenlee Textron shall not be liable for damages
resulting from misapplication or misuse of its products.
Blackburn is a registered trademark of Thomas & Betts.
KEEP THIS MANUAL
Important Safety Information
Electric shock hazard:
This tool is not insulated. Do not use
on live circuits.
Contact with live circuits could result
in severe injury or death.
An incomplete crimp can cause a re.
Use proper connector and cable combinations.
Improper combinations can result in an incomplete
crimp.
Failure to observe this warning could result in severe
injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris.
• This tool is intended for two-handed operation.
Maintain a rm grip on both handles when using
this tool.
• Inspect tool before use. If any parts are worn or
damaged, send the tool to an authorized Greenlee
service center.
• Do not perform any service or maintenance other
than as described in this manual.
• Do not exceed the rated capacity of this tool.
Failure to observe these precautions may result in
injury or property damage.
Description
The 1981 Mechanical Crimping Tool is intended for
crimping copper color-coded lugs and splices from
8 AWG through 250 kcmil and aluminum color-coded
lugs and splices from 6 AWG through 4/0 AWG.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This instruction manual
and any markings on the tool provide information for
avoiding hazards and unsafe practices related to the
use of this tool. Observe all of the safety information
provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with
the safe operation and maintenance procedures for the
following Greenlee tool:
1981 Mechanical Crimping Tool
Keep this manual available to all personnel.
Replacement manuals are available upon request at no
charge at www.greenlee.com.
1981 Mechanical Crimping Tool
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
Operation
1. Refer to the connector manufacturer’s instructions
for preparing the cable and connector.
2. Set the nest (adjustable die) of the crimping tool to
the proper cable size by turning the adjusting screw
at the top of the crimping tool until the match line on
the nest is aligned with the proper cable size.
3. Consult the Connector Selection chart for recom-
mended number of crimps.
4. Insert cable and connector assembly from either
side of the crimping tool and indent as instructed
by the connector manufacturer. To ensure a proper
crimp, close the handles until the movable handle
rests against the stop of the other handle.
Identification
Note: Do not remove the calibration plates from the
sides of the crimper frame.
Calibration Check
Set the match line on the nest to indicate 1/0 wire.
To determine if the crimping tool is properly calibrated,
insert a metal rod that ts snugly between the nest and
indicator. If the metal rod is within the range shown
on the Calibration Table, the crimping tool is correctly
calibrated.
If the diameter is not within this range, send the tool to
an authorized Greenlee service center.
Calibration Table
Set 1/0 CU to
Minimum Maximum
Metal Rod 0.353" 0.373"
9.0 mm 9.5 mm
Set 1/0 AL to
Minimum Maximum
Metal Rod 0.422" 0.442"
10.7 mm 11.2 mm
Match Line
1981 Nest
(50109090) 1981 Indentor
(50109073)
Handle Stop
Movable Handle
Adjusting Screw (50062174)
Cable Size Calibration Plate
1981 Mechanical Crimping Tool
4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070
An ISO 9001 Company • Greenlee Textron Inc. is a subsidiary of Textron Inc.
USA Tel: 800-435-0786
Fax: 800-451-2632
Canada Tel: 800-435-0786
Fax: 800-524-2853
International Tel: +1-815-397-7070
Fax: +1-815-397-9247
www.greenlee.com
Connector Selection
A — 8–1 AWG: 1 crimp
1/0 AWG–250 kcmil: 2 crimps
B — 6–4 AWG: 1 crimp
2–4/0 AWG: 2 crimps
*Use the number of crimps listed in the last column instead of the number provided with the connector:
COPPER
SPLICE
COPPER LUG
SHORT VHSS CSP YS-L ACT SCSS/SCS BCU54504–54513
LONG CU YS-LVHS ACTL SCL BBCU54804–54813
SHORT CTL YA-L/YA-L-2TC
YA-2LN/YA-L-2NT
VHCS A
CSW∆
CRA/CRB/CRC
LCAS/LCA
LCD/LCAN BLU
54104–54174
54204–54275
LONG CTL-L/LCN
YA/YAZ
YA-2N/YA-2TC
YAZ-2N/YAZ-2TC
VHCL A
CLN, CLW∆
CRA-L/CRB-L/CRA-2L
CRB-2L/CRC-2L
LCB/LCC BBLU
54929BE–54913BE
54850BE–54868BE
CONNECTOR
TYPE
BARREL
TYPE ANDERSON BURNDYBLACKBURN®NUMBER
OF CRIMPS*
ILSCO PANDUIT PENN-
UNION
T&B
AL SPLICE ASP YS-AVACS BAS/ASN SA BCUA60507–60548
AL LUG ATL YA-A/YA-A-TNVACL B
ACL/ACN
2ACL/2ACN
ALNS/ALNN/ALND LAA/LAB BLUA
60101–60157
60230–60250
Tool Range—COPPER: 8 AWG to 250 kcmil (except as noted ∆)
Tool Range—ALUMINUM: 6 AWG to 4/0 AWG
∆ILSCO Capacity: 8 AWG to 4/0 AWG
95R7
Table des matières
Autres manuels Greenlee Outils électriques
Greenlee
Greenlee Quick Draw 7804SB Manuel utilisateur
Greenlee
Greenlee 750 Manuel utilisateur
Greenlee
Greenlee GREENLEE KWIK-STRIPPER 45019 Manuel utilisateur
Greenlee
Greenlee RK12ID Manuel utilisateur
Greenlee
Greenlee ES32ML Manuel utilisateur
Greenlee
Greenlee Fairmont F20 Manuel utilisateur
Greenlee
Greenlee Fairmont RK6040 Manuel utilisateur
Greenlee
Greenlee GATOR EK6IDLX Manuel utilisateur
Greenlee
Greenlee GATOR CUAP32GL Manuel utilisateur
Greenlee
Greenlee UT10 Ultra Tugger Manuel utilisateur
Greenlee
Greenlee K2-1BGL Manuel utilisateur
Greenlee
Greenlee ESP710L Manuel utilisateur
Greenlee
Greenlee HPB45 Series Manuel utilisateur
Greenlee
Greenlee GATOR CK06FT Manuel utilisateur
Greenlee
Greenlee GPU 18-8 Mode d’emploi
Greenlee
Greenlee GATOR EK22GL Manuel utilisateur
Greenlee
Greenlee 36587 Manuel utilisateur
Greenlee
Greenlee GATOR EK622L Manuel utilisateur
Greenlee
Greenlee Quick Draw 90 7906SB Manuel utilisateur
Greenlee
Greenlee GATOR ES20L Manuel utilisateur
