Greenlee CMT-90 Manuel utilisateur

CMT-90

Clamp-on Meter

Medidor

con pinza

Contrôleur

numérique

à pinces

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and

safety information in this manual before

operating or servicing this tool.

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen en

este manual, antes de manejar esta herramienta

o darle mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de

ce manuel avant d‘utiliser ou de procéder à

l‘entretien de cet outil.

Description

The Greenlee CMT-90 Digital Clamp-on Meter is a hand-held testing device

with the following measurement capabilities: AC and DC voltage, AC current,

and resistance. It also verifies continuity. The CMT-90 is a true RMS-reading

meter.

This unit has data hold capability. It automatically determines measurement

function based on input.

The display automatically illuminates for easy viewing in dark areas.

Safety

Safety is essential in the use and maintenance of Greenlee tools and

equipment. This instruction manual and any markings on the tool provide

information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe

operation and maintenance procedures for the Greenlee CMT-90 Digital

Clamp-on Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

KEEP THIS MANUAL

All specifications are nominal and may change as design improvements occur.

Greenlee Textron Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark of

Greenlee Textron Inc.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

CMT-90

Important Safety Information

This symbol is used to call your attention to hazards or unsafe

practices which could result in an injury or property damage. The

signal word, defined below, indicates the severity of the hazard. The

message after the signal word provides information for preventing or

avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury

or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury

or property damage.

Read and understand this material before

operating or servicing this equipment. Failure to

understand how to safely operate this tool could

result in an accident causing serious injury or

death.

Important Safety Information

Electric shock hazard:

• Do not apply more than the rated voltage between any two input

terminals, or between any input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the

accessory.

Failure to observe these warnings could result in severe injury or death.

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application.

Refer to the category and voltage rating of the test lead or accessory.

• Inspect the test leads or accessory before use. They must be clean and

dry, and the insulation must be in good condition.

• Use this unit for the manufacturer’s intended purpose only, as

described in this manual. Any other use can impair the protection

provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

CMT-90

Important Safety Information

Electric shock hazard:

• Do not operate with the case or battery cover open.

• Before removing the case or battery cover, remove the test leads

(or jaw) from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Unless measuring voltage or current, shut off and lock out power. Make

sure that all capacitors are discharged. Voltage must not be present.

• Using this unit near equipment that generates electromagnetic

interference can result in unstable or inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

• Do not connect to voltage for longer than 30 seconds.

Failure to observe these precautions may result in injury and can damage

the unit.

Electric shock hazard:

Do not use the meter to measure voltages in circuits that could be

damaged by the meter’s low input impedance (approximately 4 kΩ).

Failure to observe this precaution may result in injury and can damage the

unit.

Identification

1. Jaw

2. Lever

3. Display

4. Common (COM) input terminal

5. Volts or resistance (V-Ω) input terminal

6. ON/OFF/HOLD button

7. Sensor for automatic backlit display

Display Icons

8. Low battery indicator

9. DC measurement is selected

10. –Polarity indicator

11. AC measurement is selected

12. Automatic selection is active

13. HOLD Hold function is enabled

14. LoZi Low input impedance is active

15. VVoltage

16. AAmperes

17. Ohms

18. Continuity

19.

Overload indicator

–

Symbols on the Unit

Warning—Read the instruction manual

Electric shock hazard

Double insulation

Battery

Recycle product in accordance with manufacturer’s directions

Note: Icons that

appear on the

display but are not

identified are not

used on this model.

4 5

CMT-90

*The crest factor is the ratio of the peak value to the RMS value; it is

represented by the Greek letter ξ.

AC Measurement

AC measurements are usually displayed as RMS (root mean squared) values.

Two methods of AC measurement are

average-responding RMS calibrated

and

true RMS-reading.

The average-responding RMS calibrated method takes the average value of

the input signal, multiplies it by 1.11, and displays the result. This method is

accurate if the input signal is a pure sine wave.

The true RMS-reading method uses internal circuitry to read the true RMS

value. This method is accurate, within the specified crest factor limitations,

whether the input signal is a pure sine wave, a square wave, sawtooth wave,

half wave or signal with harmonics. The ability to read true RMS provides

much more measurement versatility. The Greenlee CMT-90 is a true RMS

meter.

The Waveforms and Crest Factors table shows some typical AC signals and

their RMS values.

Waveforms and Crest Factors

Waveform

RMS Value 100 100 100 100

Rectified Value 90 100 87 64

Crest Factor* 1.414 1 1.73 2

(ξ)

Operation

2. Refer to “Typical Measurements”for specific measurement instructions.

3. Test the unit on a known functioning circuit or component of the type you

intend to measure.

•If the unit does not function as expected on a known functioning

circuit, replace the battery.

•If the unit still does not function as expected, send the unit to Greenlee

for repair. Refer to the instructions under the Warranty.

4. Take the reading from the circuit or component to be tested.

Note: Momentarily press the ON/OFF/HOLD button to hold the present

measurement on the display; momentarily press again to return to the normal

display mode. Press and hold to turn the unit off.

Priority Display Conditions

AC volts or Input at terminals is

1DC volts, 1.3 to 999.9 VAC

whichever 1.8 to 999.9 VDC

is greater –0.6 to –999.9 VDC

Input at terminals is

Resistance 0 to ∞Ω

2 and 0 to 0.9 VAC

continuity 0.2 to 1.4 VDC

–0.02 to –0.2 VDC

3 AC amps AC current through jaw is

0.6 to 600.0 A

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

1. The meter automatically selects the proper measurement according to

the following table.

CMT-90

Typical Measurements

Current Measurement—

Clamp Around Wire

Notes:

•Clamp the jaw around one conductor only.

•Close the jaw completely to ensure

accurate measurement.

•Center the wire in the jaw for highest

accuracy.

Current Measurement—

Clamp Around Line Splitter

Notes:

•The Greenlee 93-30 Line Splitter is divided.

One section renders amps; the other

renders amps multiplied by 10.

•Close the jaw completely to ensure

accurate measurement.

•Center the line splitter in the jaw for highest

accuracy.

Typical Measurements

Voltage Measurement

Resistance

Measurement

Continuity Check

Table des matières

Langues :

Autres manuels Greenlee Instrument de mesure

Greenlee

Greenlee 500XP Manuel utilisateur

Greenlee

Greenlee TS90 TelScout Manuel utilisateur

Greenlee

Greenlee 200B-G Manuel utilisateur

Greenlee

Greenlee CMT-80 Manuel utilisateur

Greenlee

Greenlee 560XL Manuel utilisateur

Greenlee

Greenlee 200fp Manuel utilisateur

Greenlee

Greenlee 200EP-G Manuel utilisateur

Greenlee

Greenlee CM-1360 Manuel utilisateur

Greenlee

Greenlee IPM-300 Manuel utilisateur

Greenlee

Greenlee Pull Connect Manuel utilisateur

Greenlee

Greenlee GOPM01 Manuel utilisateur

Greenlee

Greenlee 180XL Manuel utilisateur

Greenlee

Greenlee CM-660 Manuel utilisateur

Greenlee

Greenlee DataScout 10G Manuel utilisateur

Greenlee

Greenlee CSJ-100 Manuel utilisateur

Greenlee

Greenlee 5882A Manuel utilisateur

Greenlee

Greenlee SM-100 Manuel utilisateur

Greenlee

Greenlee 200EP-G Manuel utilisateur

Greenlee

Greenlee CLM-1000 Manuel utilisateur

Greenlee

Greenlee 93-808 Mode d’emploi

Greenlee

Greenlee GOPM Micro-01 Manuel utilisateur

Greenlee

Greenlee SML-200 Manuel utilisateur

Greenlee

Greenlee CM-600 Manuel utilisateur

Greenlee

Greenlee HCO-100 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur