Grandstream Networks HT814 Manuel utilisateur

Grandstream HT814/HT818

ATA Device Installation Guide

The Grandstream HT814 is a four-port FXS and HT818 is an eight-port FXS Analog Telephone Adapter (ATA) device

packaged in a compact chassis. These devices can be used for the following purposes:

●Fax machine on FXS port

●Local or remote phone on FXS port

Overview of the Installation Process

The HT814 and HT818 are normally pre-configured for use with our StarCloud+ telephone system. In most cases,

the installer can connect the HT814 or HT818 to the customer’s network along with the appropriate analog

telephone connections.

If the provided configuration needs to be changed, it is possible to field-program the HT814 or HT818 using the

instructions covered later in this guide.

Connecting the HT814 and HT818

The rear panel of the HT814 has a power connection, four RJ11 telephone connectors, and two RJ45 network

connectors, as shown in the following picture:

HT814 Rear View

August 2019

Communications, LLC. All logos and company names are trademarks or service marks of their respective companies.

Grandstream HT814 and HT818 ATA Device Installation Guide

The rear panel of the HT818 has a power connection, eight RJ11 telephone connectors, and two RJ45 network

connectors, as shown in the following picture:

HT818 Rear View

The connectors are used as follows:

Connector

Purpose

DC 12V

Power connector. Connect the provided AC power supply here.

Note: Does not operate on Power over Ethernet (PoE).

Connection for a laptop computer. Use this connection for field re-configuration.

Connection to the local network (if used as a local device) or to a WAN connection (if

used as a remote device).

Connections for an FXS (station) device, such as an analog telephone or a fax machine.

The LAN port is only used to access the HT814 or HT818’s built-in configuration server from a connected laptop.

This is necessary to perform the initial configuration. After the device is configured, the LAN cable can be

disconnected.

Pre-Installation Configuration

Ensure that the HT814 or HT818 device is added to the customer system and correctly provisioned using the

portal. ATA devices are added via the Multi-Extension Devices page in the portal. Analog phone and fax Extensions

are configured via the Extensions page in the portal. For more information, refer to the ATAs Portal Configuration

Guide.

The HT814 and HT818 can be configured for either local (On-Net) or remote (off-net) use. If you are re-deploying

an HT814 or HT818 that was already configured, follow the instructions in the Factory Reset



section below. Then,

configure the device for either local or remote operation. A device configured for local operation does not work as

a remote device and vice-versa, so it is important to apply the correct configuration to the HT814 or HT818.

Page 2

Grandstream HT814 and HT818 ATA Device Installation Guide

If you are unsure about the current configuration, perform the factory reset and then configure the device.

Factory Reset

To factory reset the HT814 or HT818 ATA device:

1. Unplug the cable from the WAN or LAN port.

2. Locate the small hole on the back panel of the unit next to the power connector, to the left for HT814 and

to the right for HT818.

3. Insert a straightened paper clip or other thin tool into the hole, and press for about seven seconds. Once

removed, the device resets to the factory settings.

Configure as a Local Device

To configure the HT814 or HT818 ATA device as a local device:

1. Connect an ethernet cable from a laptop computer to the LAN port on the HT814 or HT818 device.

Important: The computer must be configured to obtain an IP address automatically using DHCP.

2. Connect an ethernet cable to the local network using the WAN port.

3. Access a Web browser and direct the browser to http://192.168.2.1. The HT814 or HT818 login screen

displays.

4. For the user name and password, enter admin (all lower case) in both fields. The main configuration menu

displays.

5. Use the HT814 or HT818 configuration menu to configure the WAN port to use VLAN 41.

6. Select Advanced Settings. Scroll down to Firmware Upgrade & Provisioning: Upgrade VIA, select HTTP.

7. For the configuration server address, enter 10.41.22.99.

8. Once connected to switch on VLAN 41, the HT814 or HT818 obtains the necessary configuration data. This

will allow device registration. The HT814 or HT818 is now ready to use.

Once registered, the HT814 or HT818 can make and receive inbound and outbound calls.

Configure as a Remote Device

The HT814 and HT818 can operate as a remote device, but it requires installation-specific configuration

information to operate. For assistance, contact Star2Star Technical Support.

Page 3

Grandstream HT814 and HT818 ATA Device Installation Guide

HT814 and HT818 Status Lights

The following status lights are available on the HT814 and HT818 top panel:

Light

Blue Light Indicates

Connected to power.

Phone is connected and off-hook.

Connected to a WAN connection.

Connected to a LAN connection.

HT814 Top View

 HT818 Top View

Page 4

Autres manuels pour HT814

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Grandstream Networks Adaptateur

Grandstream Networks

Grandstream Networks HT701 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone-286 Rev 3.0 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT702 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT802 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone 503 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT802 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT701 Manuel utilisateur

Grandstream Networks

Grandstream Networks Handytone 502 Manuel utilisateur

Grandstream Networks

Grandstream Networks Handytone 502 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone-386 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT503 FXO Manuel utilisateur

Grandstream Networks

Grandstream Networks HT704 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT701 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT802 Manuel

Grandstream Networks

Grandstream Networks HT802 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT701 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone 386 Manuel utilisateur

Grandstream Networks

Grandstream Networks DUAL FXS PORT HT502 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone-801 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT-286 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT701 Manuel utilisateur

Grandstream Networks

Grandstream Networks HT814 Mode d’emploi

Grandstream Networks

Grandstream Networks HT-286 Manuel utilisateur

Grandstream Networks

Grandstream Networks HandyTone-488 Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur