Gofanco Matrix88HD20-Pro Manuel utilisateur

8x8 HDMI 2.0 Matrix Pro

User's Guide

G4-0121A

P/N: Matrix88HD20-Pro

Thank you for purchasing from gofanco. Our products

aim to meet all your connectivity needs wherever you

go. For optimum performance and safety, please read

the instructions carefully and keep this User’s Guide for

future reference. If you need more information about our

products, please visit www.gofanco.com. For technical

support, please email us at [email protected].

For drivers and manuals download, please go to

www.gofanco.com/downloads.

Important Safety Notices

Pleasereadsafetyinstructionscarefullybeforeinstallation

and operation.

• Please pay close attention to all warnings and hints

for this device

• Do not expose this unit to rain, heavy moisture, or

liquid

• Do not repair the device or open the enclosure

without professional guidance to avoid electric

shocks. Doing so may void your warranty

• Keep the product in a well-ventilated location to

avoid damage from overheating

• Shut off power and make sure environment is safe

before installation

• Do not plug the HDMI cables in/out when the

device is in use to avoid cable damage. Make sure

they are plugged into the correct ports

• Use the included DC24V power adapter only. Make

sure the specification matches if using 3rd-party DC

power adapter

PackageContents

• 8x8 HDMI 2.0 Matrix Pro

• IR remote control and IR Receiver cable

• Power adapter (24VDC/ 2.71A)

• RS-232 cable

• Mounting accessories and Plastic cushions (4pcs)

• User's guide

Introduction

The 8x8 HDMI 2.0 Matrix Pro allows you to connect up to

eightHDMI source devicesand independently distribute

any source to any of the eight HDMI displays.

Features

• Supports up to 4K@60Hz YUV 4:4:4

• HDMI 2.0 and HDCP 2.3 compliant

• Supports audio matrix and audio extraction

• Equipped with 8 SPDIF Toslink and 8 analog (L+R)

audio outputs

• Supports 4K to 1080p downscaling on the last 4

outputs (5-8)

• HDMI outputs provide 2.5W to power Active

Optical Cables (AOC)

• Features comprehensive EDID management and

advanced HDCP handling

• Controllable via front panel buttons, IR, RS232 and

TCP/IP

Installation Requirements

• HDMI source devices (computer, DVD player,

XBOX, PS3, etc)

• HDMI display devices (SDTV/Monitor, HDTV/

Monitor, projector, etc.)

Product Layout

Figure 1: Front Panel Layout

1. Power LED: Green when the Matrix is powered on.

Red when the Matrix is in standby mode

2. IR Sensor: Receives IR signals from the included

remote control

3. Select Buttons (x16):

Input Select Button (x8): Each button includes 1

LED, one for each source input

Output Select Button (x8): Each button includes 1

LED, one for each display output

4. Control Buttons (x4):

Enter: Press to confirm the operation

Lock: Press for 3 seconds to lock/unlock all from

buttons

All: Selects one input source to display on all

outputs. Example: Source device on input 1 to

display on all displays: Press Input Select 1 + All

+ Enter

Clear: Press this button to clear your selection

5. Memory Save/ Memory Recall: Stores the Matrix'

current switch status to memory

Memory Save: Press and hold button 1-4 to save the

current configuration into memory

Memory Recall. Press button 1-4 to recall the

configuration saved to memory

Figure 2: Rear Panel Layout

1. HDMI In (1-8): Connects to your HDMI sources

2. HDMI Out (1-8): Connects to your HDMI displays.

HDMI Out 5-8 supports auto downscaling feature

3. Audio Matrix Outputs:

SPDIF (x8): Digital audio outputs for de-embedded

HDMI audio, 8 in total

RCA/ L+R (x8): Analog audio outputs for de-

embedded HDMI audio, 8 pairs in total

4. IR Input: Connects to the included IR Receiver

cable. Receives IR signals from the included remote

contoller. This connection is optional see page 6,

step 5 for more information.

5. RS232: Connects to your control PC using the

included RS232 cable

6. Firmware Update: Type-A USB port for firmware

update

7. RJ45: Connects to your control PC's Ethernet port

for TCP/IP control

8. PowerJack: Connects to theincludedpower adapter

Hardware Installation

1. Power off all devices including your HDMI sources

and HDMI displays.

2. Connect your HDMI source devices to the HDMI

IN(1-8) connectors with HDMIcables(HDMI cables

not included).

3. Connect your HDMI displays to the HDMI OUT (1-

8) connectors with HDMI cables (HDMI cables not

included).

4. Optional: Connect your PC to the Matrix Pro's RJ45

port using a CAT cable this connection is needed

only if you require device control via Web GUI. See

TCP/IP Control on page 12 for more information.

5. Optional: Plug the included IR Receiver cable into

the Matrix's IR Input connector, this connection is

needed only if the front panel IR sensor is blocked

andnot responding tocommandsfrom the included

Remote Controller.

6 Optional: Plug the included RS232 cable into the

Matrix'sRS232 connector thenconnect the other end

to an RS232 serial port of your computer, this

connection is needed only if you require RS232

device control via a computer system. See RS232

Control on page 22 for more information.

6. Plug the included power adapter into the power

jack then plug the power adapter into a reliable

power source.

7. Power on all connected devices.

8. The HDMI 8x8 Matrix is ready for use.

Connection Diagram

Figure 3: Connection Diagram

Device Control

Front Panel Control Buttons

Input Select/ Output Select

The front panel features eight input and eight output

selection buttons for switching sources and displays.

Please see the device switching examples below.

1. To configure 1 input to 1 output

Example: Source device on Input 1 to display on

Output 3

- Press Inputs 1 + Outputs 3 + Enter button

2. To configure 1 input to multiple outputs

Example: Source device on Input 1 to display on

Outputs 3, 6, and 7

- Press Inputs 1 + Outputs 3, Outputs 6, Outputs 7+

Enter button

3. To configure 1 input to All outputs

Example: Source device on Input 2 to display on All

Outputs

- Press Inputs 2 + All + Enter button

Note: The selected buttons LED indicators will blink

three times then turn off when switching is successful. If

switching fails all LEDs will turn off immediately.

Input Device / Output Device Recognition

Press any Output Select button and the corresponding

Input Select LED will light up.

Lock

Hold down the lock button for 3 seconds to disable all the

front panel buttons. Hold down the button again for 3

seconds to unlock the buttons.

Memory Save/ Memory Recall

Stores the Matrix' current status into memory. Allows for

one button access to your favorite source to display

setup.

Memory Save: Press and hold button 1-4 to save the

current configuration into memory.

MemoryRecall.Pressbutton1-4torecalltheconfiguration

saved to memory.

Clear

Press this button to cancel the current operation.

IR Remote Control

• Press the Standby (1) button

to enter or exit Standby

mode

• To switch an input to one or

more outputs, first press the

number corresponding to

the desired INPUTS (2),

then press one or more

OUTPUTS (3) or the ALL (4)

button, then press the Enter

(4) button to execute the

command, or press Clear (4)

to cancel

• To set the EDID for one or

more source devices to the

EDID capabilities of a specific

output, first press the EDID

(4) button, then press the

desired INPUTS (2) button,

then press the OUTPUTS (3)

button corresponding to the

desired display, finally press

theEnter (4) button to execute

the operation, or press Clear

(4) to cancel.

Table des matières

Autres manuels gofanco Changer

gofanco

gofanco USBCMST2HD-4K60 Manuel utilisateur

gofanco

gofanco HDRswitch3P Manuel utilisateur

gofanco

gofanco USBCMST3VID Manuel utilisateur

gofanco

gofanco mDPMST2DP Manuel utilisateur

gofanco

gofanco PRO-QuadView Manuel utilisateur

gofanco

gofanco SwitchBYOD41 Manuel utilisateur

gofanco

gofanco EthSwitch24P Manuel utilisateur

gofanco

gofanco HDRswitch5P Manuel utilisateur

gofanco

gofanco HDRswitch4P-Aud Manuel utilisateur

gofanco

gofanco DPMST2DP Manuel utilisateur

gofanco

gofanco Matrix44HD2-LT Manuel utilisateur

gofanco

gofanco DP14MST2HD Manuel utilisateur

gofanco

gofanco KVMScaler2P Manuel utilisateur

gofanco

gofanco Prophecy PRO-KVMDP-4P Manuel utilisateur

gofanco

gofanco KVMDP-2P Manuel utilisateur

gofanco

gofanco KVMHD2-4P Manuel utilisateur

gofanco

gofanco EthSwitch24P-2 Manuel utilisateur

gofanco

gofanco Switch3P-HD20 Manuel utilisateur

gofanco

gofanco Prophecy PRO-KVMaud4P Manuel utilisateur

gofanco

gofanco Switcher5p Manuel utilisateur

gofanco

gofanco KVMHD2-2P Manuel utilisateur

gofanco

gofanco Switch41-HD20 Manuel utilisateur

gofanco

gofanco Switcher3P Manuel utilisateur

gofanco

gofanco USBCMST2DP Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

gofanco Matrix88HD20-Pro Manuel utilisateur

Manuels Changer populaires d'autres marques