Gloster 769 Manuel utilisateur
AMBIENT
LANTERN
USER MANUAL
GENERAL SAFETY GUIDELINES
DISTRIBUTED IN THE USA BY:
DISTRIBUTED IN EUROPE AND ROW BY:
REMOTE CONTROLLER
ADAPTER AND LED LIGHT UNIT
INITIAL CHARGING
WARRANTY STATEMENT
SPECIFICATION
OPERATION
Read this guide carefully before using the product.
Keep this guide for future reference, do not throw away.
Only use the product in accordance with these instructions. Failure to follow the instructions contained
within the user guide can result in damage to the product, and the warranty will become void.
Any responsibility is disclaimed due to incorrect use of the product.
• Do not use any adapter for charging other than the adapter supplied with the product,
as this could be dangerous.
• Do not use the adapter supplied to charge any product other than the product supplied,
as this could also be dangerous.
• Do not use near sources of direct heat, or expose the product to fire.
• Do not use the light unit outdoor without the charger socket cap fastened in position.
• This product is not intended for use by children.
• Do not try to open the charger adapter. A faulty charger should be returned to the dealer.
• Always disconnect the charger after use.
Gloster Furniture
1075 Fulp Industrial Road
PO Box 738
South Boston
VA 24592
USA
Gloster Furniture Limited
Collins Drive
Severn Beach
Bristol BS35 4GG
United Kingdom
• To activate, pull the power separation film from the
battery compartment
• Ensure that the lamp is fully charged before using
• To turn the lamp on, press the power button
• To increase the intensity of the light, press the + button
• To decrease the intensity of the light, press the - button
• NOTE: Lithium battery CR2025 x 1pc (3V).
Small parts should be kept away from children
• The remote control unit is not waterproof
Adapter Input: 100V-240V DC – 50Hz-60Hz
Adapter Output: 4.2V-5V – 0.5A-1.2A
LED Light Unit Battery Type: Li-ion 3.7V-4V, 1100mAh -3600mAh
LED Light Unit Battery is non-replaceable. The complete LED unit must be replaced.
Full recharge: 5-6 hrs
Working time on single charge: 8-10 hrs
LED Lifespan: ≥50,000hrs (2.8W≤Watt≤28.8W)
Working Temperature Range: +60 °C / -20 °C
NB: Charger is for INDOOR USE ONLY. Charging must ALWAYS be carried out INDOORS.
NEVER CONNECT THE CHARGER TO THE LIGHT UNIT OUTDOORS.
• Make sure that the light is switched off.
If the light is on, the battery will not charge.
• Pull out the plastic cap from the LED unit housing.
• Plug the adapter in to a mains power outlet.
• Plug the DC connector in to the DC socket in
the LED unit.
• When the unit is charging, the light on the front
face of the adapter will appear red.
• If the light on the front face of the adapter
appears green, then the unit is fully charged.
• To extend the life of the battery, charge the
LED unit for at least 10 hours for initial charging.
• Remove the DC connector from the LED unit
and replace the plastic cap.
• Make sure that the plastic cap is securely fastened
to prevent water from entering the LED unit.
If the plastic cap is not replaced, water can enter
into the LED unit and cause damage that will affect
the function of the light.
This product is guaranteed for a period of 2 years against issues arising due to defective design,
workmanship or materials.
This warranty does not cover damages, losses, defects or malfunctions arising from misuse,
improper installation, or any manner of tampering with the product, including: using the incorrect
electric supply or voltage; usage other than in accordance with the instruction manual;
normal wear and tear.
No repair shall be undertaken as a result of any of the causes mentioned in the above statement.
This warranty is void if at any time part or parts of the product are removed, altered, tampered with,
adjusted, modified, dismantled, repaired or handled in anyway by any person not authorized to do so.
If the adapter cord of this product becomes damaged, it shall be exclusively replaced by the
supplier, his service agent or a similar qualified person in order to avoid potential hazard.
Item Name: Ambient Lantern
Voltage: 5V DC
Power: Max 20W
Manufacturer: PT Gloster Furniture Ltd
Model Number: 769
To switch the light on, either push the on/off button on the remote control, or the red on/off button
on the underside of the light unit.
The light unit will always switch on at the maximum light intensity.
To adjust the light intensity, push the +/- button until the desired light level is reached.
To switch the light off, either push the on/off button on the remote control, or the red on/off button
on the underside of the light unit.
ON/OFF
Silica gel cap
ASSEMBLY GUIDE
E
E
E
E
E
E
E
E
E
E
AMBIENT
LANTERN
Autres manuels Gloster Éclairage extérieur
Manuels Éclairage extérieur populaires d'autres marques
Lindby
Lindby 9949029 Manuel utilisateur
HEPER
HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation
HEPER
HEPER LW8034.003-US Instructions d'installation et d'utilisation
Maretti
Maretti VIBE S 14.6080.04.A Manuel utilisateur
BEGA
BEGA 84 253 Manuel
HEPER
HEPER MINIMO Instructions d'installation et d'utilisation
LIGMAN
LIGMAN BAMBOO 3 Manuel utilisateur
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur
urban ambiance
urban ambiance UQL1273 Manuel utilisateur
TotalPond
TotalPond 52238 Manuel utilisateur
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuel utilisateur