Girard Systems GC274B Manuel utilisateur

AC MOTOR CONTROL MODULE

GC274B

INSTALLATION and PAIRING INSTRUCTIONS

REV.12302015

RV AWNING PRODUCTS

1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (800) 382-8442 FAX (949)276-5500

www.girardrv.com

Page 2of 11

Girard Systems awnings may be operated in light wind and rain

conditions. When periods of heavy rain and or high wind are expected

the awning must be closed. Never leave the awning open and

unattended.

Damage caused by wind and rain is not covered by warranty.

All awnings must be closed prior to moving the vehicle for any reason.

As an extra safety precaution a visual check that every awning is fully

closed is required.

Damage caused by failure to comply with these instructions is

not covered by warranty.

Before using your awning, ensure that the area into which the awning

will be deployed is free of obstructions (Trees, walls, pillars, posts,

other vehicles etc.)

Damage caused by collisions with any of the above or similar is

not covered by warranty.

Before using your awning make sure that all of your electrical circuits

are operating correctly. Recreational Vehicles can generate AC power

from three separate sources. The electrical system transfer switch in

your vehicle will select power for the awning as follows:

Shore Power – if connected;

Generator Power – if the generator is running;

Inverter Power – batteries must be charged for inverter operation.

Girard Systems awnings are supplied with an electric motor appropriate to the

product.

Page 3of 11

CONTENTS

Product description ….…………………………………………………………………………..….. 4

Specification ……………………………………………………………………………………………. 5

Wiring Diagram ……………………………………………………………………………………….. 6

Set up and Programming ..………………………………………………………………………… 7

Change Motor Direction ……………………………………………………………………………. 7

Programming to a remote controller ………………………………………………………….. 7

Cancel a remote controller ……………………………………………………………………….. 8

Cancel all remote controllers …………………………………………………………………….. 8

Programming to an Anemometer …………………………………………………………….... 8

Programming to a Motion Sensor ……………………………………………………..…… 9-11

THE G–LINK SYSTEM

The G-Link motors and control modules provided by Girard Systems communicate by

use of RF signals on a frequency of 433.92 MHZ. This eliminates the need for wiring

and the drilling of holes in the vehicle. These components must be electronically

matched, programmed or paired before use. This is usually done at the Girard Systems

factory. Should the need arise for the user to pair a device with the motor controller

they must refer to the appropriate manual for the devices applicable to their particular

installation.

Page 4of 11

PRODUCT DESCRIPTION

AC Motor Controller with LED (12V DC) control plus Ignition retract and lockout.

Fig.1

•This module is designed to control a single Standard 110v AC Motor up to 8 Amps and

can be remotely operated with any paired G-Link handset or wall switch.

•The controller will receive signals from a distance of more than 500ft in open air and

more than 100ft in the presence of obstructions. The RF transmission frequency is

433.92MHZ.

•The GC274B may be programmed with up to 20 compatible remote modules. If an

additional module is programmed it will replace the most recently programmed module.

The previous 19 modules will remain unchanged.

•The command to retract the awning can be initiated by turning on the ignition switch or

by releasing the parking brake depending upon how it is installed.

•This module will cause the awning to retract when the vehicle prepares to move and

then remove power to the awning so that it cannot be redeployed while the vehicle is in

motion.

FWD

STOP

REV

Page 5of 11

Fig.2

1) 110v AC power supply from vehicle power distribution board.

2) Output to awning motor control.

3) Initiate retract signal from vehicle ignition or parking brake.

4) 12v DC to LED lighting.

Specifications

POWER: 110VAC / 60Hz

AC Input: White = Neutral / Black = Live / Green = Earth

To the Motor: White = Neutral / Red = Direction 1 / Black = Direction 2 / Green = Earth

Ambient T: 0 - 130°F

Installation

A circuit breaker protected 15A/115v AC power supply is required form the Vehicles power

distribution panel as shown in the diagram below.

1. Install a UL approved 110VAC junction box in which to make the electrical connections.

2. Route the Awning’s Motor cable to this location and make the connections to the

GC274B in accordance with NEC requirements.

Mount the GC274B on the wall using the screws and tape provided.

Page 6of 11

Page 7of 11

SETUP AND PROGRAMMING

1. Change motor direction

a. Supply power to GC274B

b. Simultaneously press the LEFT and RIGHT buttons of the GC274B for at least 6 seconds. The

Green LED will illuminate and then blink a few times. When the Green LED extinguishes, the

operation is complete.

Fig.3

Note; when carrying out this part of the procedure each step must be executed

within 10 seconds of the previous one or the module will revert to factory settings.

It is highly recommended that you read and understand the following sequence

before attempting to execute it.

2. Programming the GC274B to a Remote handset or Wall switch

a. Supply power to the GC274B

b. Press and hold the MIDDLE and RIGHT buttons on the GC274B (Fig 3) for about 5

seconds until the Green LED starts to flash.

c. Press STOP (Fig. 1): The Green LED will stop blinking and remain illuminated.

d. Press the UP button on the REMOTE DEVICE being programmed. The Green LED on

the motor controller will extinguish.

CHANGE MOTOR DIRECTION

PROGRAM MODE

Page 8of 11

3. Cancel one Remote from the GC274B

a. Supply power to the GC274B

b. Press and hold the MIDDLE and RIGHT buttons on the GC274B (Fig 3) for about 3

seconds until the Green LED starts to flash.

c. Press STOP (Fig. 1): The Green LED will stop blinking and remain illuminated.

d. Press the DOWN button on the REMOTE DEVICE being cancelled. The Green LED

will extinguish.

4. Cancel all of the Remotes from the GC274B

a. Supply power to GC274B

b. Simultaneously press the STOP and LEFT button of the GC274B for at least 6

seconds: The Green LED will first illuminate and then blink a few times. When the

Green LED extinguishes the operation has been completed.

5. Programming the GC274B to an Anemometer (98GC116I)

a. Supply power to the GC274B and the GC116I(Leave them on if already on)

b. Press and hold the MIDDLE and RIGHT buttons on the GC274B (Fig 3) for about 3

seconds until the Green LED starts to flash.

c. Press the STOP button on the GC274B (The Green LED will remain illuminated)

d. Press the UP button on the GC116I.

e. Extend awing using a Remote Control and press the UP button again on the GC116I

to verify that the unit is working properly (the awning should Retract)

f. Set the wind speed adjustment dial of the anemometer to in between 1-2.

Wind speed adjustment

Up Button

P2 Button

LED

Page 9of 11

6. Programming the GC274B to a Motion Sensor (98GC779G)

This procedure will require opening up the motion sensor module by following the directions

below;

a. Remove the 2 small cross head screws which secure the motion sensor to the mounting

bracket. See Fig.1.

Fig.1

b. Detach the motion sensor from the bracket, the base plate is magnetized so will need to

be gently lifted off. Then turn it over. See Fig.2.

Fig.2

Page 10 of 11

c. Remove the 4 cross head screws holding the module together. Remove the base plate

and silicone insert. See Fig.3.

Fig.3

d. Turn the base plate over (Magnet down). Then place the motion sensor on top of it so

that the magnet is aligned with the reed switch. See fig.4. If this is not done the

default program cannot be changed.

Fig.4

Base plate

Magnet

Silicone Insert

Reed Switch

LED

Sensitivity Dial

Program Button

Table des matières

Autres manuels Girard Systems Unité de contrôle

Girard Systems

Girard Systems GC274C Manuel utilisateur

Girard Systems

Girard Systems 98GC1102 Mode d'emploi

Girard Systems

Girard Systems 98GCK-36A Manuel utilisateur

Girard Systems

Girard Systems GC1149A Manuel utilisateur

Girard Systems

Girard Systems GC946G Manuel utilisateur

Girard Systems

Girard Systems 98GCK-45DR Guide d'installation

Girard Systems

Girard Systems 98GCK-16 Manuel utilisateur

Girard Systems

Girard Systems 98GCK-32B Manuel utilisateur

Girard Systems

Girard Systems GC136 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur