Giantec GT-460 Manuel utilisateur
GT-460/461
All-in-One 486
w/VGA w/ETHERNET
w/Flash Disk, Half-Size
User’s Guide
@ Copyright 1998
All Right Reserved
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or the possibility
of such damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Acknowledgments
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
Nov., 1998
Printed in Taiwan
Version A
Check List
Before getting started, please check if the 486 All-in-One Single Board
Computer package includes the following items:
l486 All-in-One board x 1pc
lVGA Driver & Utility diskette x 4 pc
lEthernet driver & utility diskette x 1 pc
lUpdating BIOS Utility diskette x 1 pc
lKeyboard/Mouse adapter x 1pc
lFDD cable x 1 pc
lHDD cable x 1 pc
lCOM2 and Printer extension cables with bracket x 1pc
lUser’s manual x 1pc
Table of Contents
Chapter 1. Introduction
1.1 Specifications………………………………………… 1-1
Chapter 2. Jumpers and Connectors
2.1 Jumpers setting……………………………………… 2-2
2.2 Connectors……………………………………………. 2-4
Chapter 3. Installations
3.1 Installing the SIMMs.……………………………….. 3-1
3.2 Installing the CPU……………………………………. 3-1
3.3 Completing the Installation…………………………. 3-2
Chapter 4. Award BIOS Setup
4.1 Entering Setup………………………………………. 4-1
4.2 The Main Menu……………………………………… 4-4
4.3 Standard CMOS Setup……………………………… 4-7
4.4 BIOS Features Setup………………………………… 4-11
4.5 Chipset Features Setup…………………………….. 4-16
4.6 Power Management Setup………………………… 4-17
4.7 PCI Configuration Setup……………………………. 4-22
4.8 Password Setting……………………………………. 4-25
4.9 IDE Auto Detection………………………………….. 4-26
4.10 Hard Disk Low Level Format Utility………………. 4-29
4.11 Power on Boot……………………………………….. 4-31
4.12 BIOS Reference - POST Codes……………………. 4-31
Chapter 5. Display
5.1 Drivers and Utilities
5.1.1 Microsoft Windows 3.1……………………….. 5-1
5.1.2 MS Windows 95/NT Mode Driver Install …… 5-2
5.1.3 MS Windows 95 Refresh Rate Utility ……… 5-2
5.2 Panel Support
5.2.1 For 40K BIOS……………………………………. 5-3
5.2.2 For 44K BIOS……………………………………. 5-4
5.3 Video Modes……………………………………….. 5-6
Appendix A. Watchdog Timer
Appendix B. Connectors’ Pin Assignment
Appendix C. Installing Disk On Chip
Appendix D. Updating BIOS
Appendix E. I/O address map
Appendix F. memory address map
Appendix G. Ethernet Software Configuration
Appendix H. Mechanical drawing
User’s Guide
Introduction
1-1
Chapter 1
Introduction
The 486 all-in-One Single Board Computer comes equipped with either Intel /
AMD / Cyrix / SGS Thomson 80486 CPU series. Also included on-board are
CHIPS 65550 VGA GUI Accelerator controller, Ethernet controller, one
socket for Flash Disk, two serial RS-232 ports (one for RS232 / RS422 /
RS485), enhanced bi-directional parallel port, PCI enhanced IDE hard disk
drive interface, floppy disk controller and watchdog timer. The 486 All-in-One
board industrial-grade construction ensures continuous, reliable operation in
harsh industrial environments.
Its video section features the ability to control most EL, mono/color STN and
TFT flat panel display as well as standard VGA. Equipped with 1MB of EDO
DRAM, up to 2MB EDO DRAM (optional). The CHIPS 65550 can display in
640x480 resolution on commonly used flat panels and true color displays on
CRT’s.
You can also use this reliable 486 All-in-One to transform any system into a
32-bit 486 compatible computer. Its highly compact form and numerous
features make it an ideal cost/performance solution for high-end commercial
and industrial applications when fast CPU speed and low mean-time-to-
repair are critical.
1.1 Specifications
. Bus Type:
ISA bus - 98 pin for 16 bit ISA bus
. CPU:
On board equipped with SQFP CPU, speed up to AMD 5x86-133.
. Cache:
256KB/512KB 2nd level cache memory
User’s Guide
Introduction
1-2
. Memory:
Supports FPM/EDO DRAM module.
Supports on board 4 MB DRAM and one 72-pin SIMM sockets,
Or two 72-pin SIMM sockets accept 1,2,4,8,16 or 32 MB SIMM module.
. Chipset:
System Chipset: ALI M1487/M1489
I/O Chipset: SMC 37C669
. Real Time Clock:
SGS M48T86 PCI (or compatible) with lithium battery backup for 10 years
of data retention
. Display:
-Chipset: C&T 65550 PCI local bus flat-panel with Windows accelerator
and Video play back
- Display memory: on board EDO DRAM 1MB up to 2MB
- Display resolution:
Supports Flat-panel resolutions up to 640x480, 800x600, 1024x768,
1280x1024
Supports non-interlace CRT monitors, 1024x768 64K colors
- Display connector: DB-15 VGA connector for CRT monitor and 2x22 pin
header for Flat-panel
- Support 3.3V and 5V Flat-panel
. Networking:
Realtek RTL8019AS Ethernet controller, 10 base T with RJ-45 connector.
. S.S.D.:
Socket for M-system Disk on Chip
. IDE:
Supports up to two, PCI mode 4 enhance IDE hard disk interface
. Floppy:
Supports up to two floppy disk drivers, 3.5” and/or 5.25”
. Parallel Port:
Enhanced Bi-directional EPP/ECP parallel port
. Serial port:
One RS232 port with 16C550 UART
One RS232/422/485 port with 16C550 UART
User’s Guide
Introduction
1-3
. Watchdog Timer:
Can generate a system RESET, The timer interval is 0 ~ 63 sec (14 level)
. Keyboard Connector:
One 6 pin Mini_Din connector is located on the mounting bracket
One pin header connector for external keyboard adapter
. Expansion Bus:
A 16 Bit PC104 connector for expansion modules
. Power Supply Voltage:
Single power +5V/2.5A, 8_pin external power connector
. Operating Temperature:
32°to 140°F (0°to 60°C)
. Board Size:
185mm X 122mm
User’s Guide
Jumpers & Connectors
2-1
Chapter 2
Jumpers and Connectors
Figure below shows the jumpers’ and connectors’ location on the 486 All-in-
One board.
User’s Guide
Jumpers & Connectors
2-2
2.1 Jumpers Setting
Speaker/Keylock/Reset/Turbo/LED (J1) J1
Internal buzzer 1-3
External speaker (remove 1-3) 1-7
Power LED, Pin 2+, Pin6- 2-6
Keylock 8-10
System reset switch 11-12
Turbo Switch 13-14
Turbo LED, Pin16+, Pin15- 15-16
HDD LED, Pin18+, Pin17- 17-18
External keyboard (J5) J5
Keyboard clock 1
Keyboard data 2
No Connect 3
Keyboard ground 4
Keyboard power 5
M-System Address Select (JP1, 1-6) JP1
1-2 3-4 5-6
CC00-CDFF open close close
D000-D1FF open open close
D800-D9FF open close open
E000-E1FF open open open
Watchdog Timer (JP1, 7-8) JP1
Watchdog time out gen. system reset 7-8
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Giantec Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
