GFA 10003166 10011 Manuel utilisateur
Installation Instructions
ELEKTROMAT
SI 25.15-30,00
Model: 10003166 10011
-en-
Status: 30.05.2018
2
GfA ELEKTROMATEN GmbH & Co. KG
Wiesenstraße 81
D-40549 Düsseldorf
www.gfa-elektromaten.de
3
Table of contents
1General safety information .............................................................................................. 4
2Technical Data ................................................................................................................ 5
3Mechanical installation .................................................................................................... 6
4Electrical installation ..................................................................................................... 10
5Limit switch adjustment ................................................................................................. 11
6Motor connection .......................................................................................................... 12
7Alternative motor connection ......................................................................................... 12
8Limit switch connection ................................................................................................. 13
9Emergency manual operation (emergency hand crank) ................................................ 14
10Completion of commissioning / testing .......................................................................... 16
11Declaration of incorporation / conformance ................................................................... 18
Symbols
Warning - Potential injury or danger to life!
Warning - Danger to life from electric current!
Note - Important information!
▶ Requirement - Required action!
Schematic representations are based on product examples. Deviations from delivered
products are possible.
4
1 General safety information
Specified normal use
The drive unit is intended for doors, which have to be secured against falling down; a safety
brake is included in the gearbox. The drive unit is directly mounted on the door shaft.
The safe operation is only guaranteed with normal specified use. The drive unit is to be
protected from rain, moisture and aggressive ambient conditions. No liability for damage
caused by other applications or non-observance of the information in the manual.
Modifications are only permitted with the agreement of the manufacturer. Otherwise the
Manufacturer’s Declaration shall be rendered null and void.
Safety information
Installation and initial operation tasks are to be performed by trained, skilled fitters only.
Only trained electrical craftsmen are permitted to work on electrical equipment. They must
assess the tasks assigned to them, recognise potential danger zones and be able to take
appropriate safety measures.
The installation is only to be carried out with the supply off.
Observe the applicable regulations and standards.
Coverings and safety devices
Do not operate unless corresponding coverings and safety devices are fitted/installed.
Ensure that gaskets are correctly positioned and cable glands are correctly tightened.
Spare parts
Use only original spare parts.
5
2 Technical Data
Type SG 63F
Output torque 250 Nm
Output speed 15 rpm
Output shaft / hollow shaft 30,00 mm
Locking torque moment 510 Nm
Safety brake (testhouse/approval number) 14-003612-PR02
Maximum output speed open / close
for frequency inverter operation 26 / 15 rpm
Supply voltage 3N~ 400 V
Operating current 2,30 A
Operating frequency 50 Hz
Power factor cos φ 0,53
Maximum movement per hour 20 h-1
Hand forces 118 N
Class of protection IP 65
Limit switch range
(maximum revolutions of output shaft / hollow shaft) 20
Temperature range -10 / +40 (+60) °C
1) When using a temperature range of +40°...+60°C use half of maximum movements per hour.
6
3 Mechanical installation
Prerequisites
The permissible loads on walls, fastenings, mountings and transmission elements must not
be exceeded, even for maximum holding torques or locking torques (▶ refer to technical
data).
Connection elements
▶ Self-locking connection
elements with a minimum
strength of 800 N/mm2
(8.8) must be used.
▶ Utilize the hole diameter
to the full.
▶ Use adequately
dimensioned washers for
elongated holes.
BAGAB00002_Z002 BAGAB00003_Z002
3 : 1
Permissible mounting positions
BAGAC02001_Z002
7
Mounting
Three elongated holes are provided for mounting.
▶ Use at least 2 of these (①) for mounting. Always use elongated hole ❶.
A key is used to connect to the door shaft.
▶ Use a key that is at least as long as the hollow shaft (②).
BAGAD02001_Z002
8
Installation
The descriptions below apply to general door specifications. The specifications of the door
manufacturer must also be observed during installation.
Warning - Potential injury or danger to life!
During installation, be sure to use a lifting device that has a sufficient load-carrying
capacity.
▶ Thoroughly grease the door shaft.
BAGAE02001_Z001
▶ Mount the keys. Pay attention to the
possible versions Ⓐ or Ⓑ.
BAGAE02003_Z002
9
▶ Attach the drive unit.
BAGAE02007_Z002
▶ Tighten all connection elements (M12) to
75 Nm. Install all other connection
elements according to the specifications of
the door manufacturer.
BAGAE02011_Z003
8.8
8.8
75 Nm
▶ Secure the keys (version Ⓑ only).
BAGAE02012_Z003
10
4 Electrical installation
Warning - Danger to life from electric current!
Switch the mains OFF and check that the cables are de-energised
Observe the applicable regulations and standards
Make a proper electrical connection
Use suitable tools
Performing electrical installation
Remove the cover. Insert the motor plug. Insert the limit switch plug.
BAH AA 0 3_ Z0 0 1
BAHAC07_Z001
Completing the electrical installation
Mount the cable entries and/or cable glands.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels GFA Entraînement CC
GFA
GFA ELEKTROMAT SI 35.30-40,00 Manuel utilisateur
GFA
GFA ELEKTROMAT FS 25.20-30,00 Manuel utilisateur
GFA
GFA 10003900 10011 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 25.15-30,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 25.15-30,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SIK 17.10 WS-30,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 55.40 FU-40,00 Manuel utilisateur
GFA
GFA 10005230 10012 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 55.15-40,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 25.15-30,00 Ex Manuel utilisateur
GFA
GFA ELEKTROMAT SI 25.15-30,00 Ex Manuel utilisateur
GFA
GFA SIK 25.10-30,00 Manuel utilisateur
GFA
GFA 10003917 10011 Manuel utilisateur
GFA
GFA 10004055 10011 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 25.24-30,00 Manuel utilisateur
GFA
GFA 10003697 10011 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 75.15-55,00 Manuel utilisateur
GFA
GFA SI 15.140 FU-40,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SI 14.15-25,00 Manuel utilisateur
GFA
GFA ELEKTROMAT SE 14.15-25,40 ER Manuel utilisateur
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
