General LM30 Manuel utilisateur
INSTRUCTION MANUAL
LM30 30m Laser Distance Measurer
Please read this instruction manual before operating this
product. Please store this instruction manual in the carry
case for future reference.
CAUTION: Class 2 Laser Product
Do not stare directly into the laser beam from apertures.
Keep out of reach of children.
Due to the electromagnetic radiation interference to other
equipment and devices please do not use the laser distance
measurer in an airplane or around medical equipment.
Do not use in a ammable, explosive environment.
Discarded batteries or devices should not be processed with
household garbage. Please follow related laws
and regulations.
Do not disassemble the instrument or attempt to perform
any internal servicing as this will void your warranty. No user
serviceable parts included.
Only approved and authorised service technicians can carry
out warranty repairs.
SAFETY
CONTROL PANEL
Power on / read
Menu / function select
Clear / back / power off
LCD DISPLAY ICONS
Full battery Single distance measurement
Area measurement
Volume measurement
Single pythagorean
measurement
Double pythagorean
measurement
Empty battery
Measurement taken
from top of unit
Measurement taken
from bottom of unit
Laser light on
HistoryAddition
Subtraction
USING YOUR DISTANCE MEASURER
POWER SUPPLY
‣ The General LM30 is supplied with two AAA alkaline batteries
‣ To replace batteries remove the battery door at the back
of the device. Place batteries according to polarity and
replace battery door.
‣ For infrequent use please take out the battery to avoid
corrosion to the body of the device.
OPERATION
‣ To turn the unit on press the power on / read button.
‣ To turn the unit off press and hold the clear / back / power off
button for two seconds.
‣ The unit will shut o automatically after 5 minutes without use.
Unit setting
‣ Press the menu button 8 times to enter unit settings.
‣ Press the power on / read button to cycle through the optional
units: m, ft, in, ft & in.
‣ Press the clear / back / power off button to exit unit settings.
Measurement reference point
‣ Press and hold the menu button to enter setup mode.
‣ The measurement taken from top of unit and measurement
taken from top of unit icon will flash alternately. Release the
menu button to select.
‣ After powering off the unit will default back to measurement
taken from bottom.
View history
‣ Press the menu button to view history.
‣ When the history icon appears press the power on / read
button. The previous 20 measurement will be displayed on
the screen.
‣ Press the clear / back / power off button to exit history.
MEASUREMENT
Single Measurement
‣ Hold the unit and point towards the measurement target.
Press the power on / read button. The laser will be emitted.
‣ Re-press the power on / read button to take the measurement.
Results will be shown on the display screen.
‣ The laser will turn off automatically after 20 seconds of inactivity.
Continuous Measurement
‣ Press and hold the power on / read button for 3 seconds. The
laser will be emitted with result shown on the display screen.
‣ Move the unit until the required distance is displayed.
‣ Press the clear / back / power off button to exit continuous
measurement mode.
Area Measurement
‣ Press the menu button four times to enter area measurement
mode. A rectangle will appear on the display screen with one
edge flashing.
‣ Press the power on / read button to take the first measurement
(length).
‣ Press the power on / read button to take the second
measurement (width).
‣ The area will be calculated automatically with results shown
on the display screen.
‣ Press the clear / back / power off button to clear data. Press
and hold the clear / back / power off button to exit area mode.
Volume Measurement
‣ Press the menu button five times to enter volume measurement
mode. A cube will appear on the display screen with one
edge flashing.
‣ Press the power on / read button to take the first measurement
(length).
‣ Press the power on / read button to take the second
measurement (width).
‣ Press the power on / read button to take the third measurement
(height).
‣ The volume will be calculated automatically with results shown
on the display screen.
‣ Press the clear / back / power off button to clear data. Press
and hold the clear / back / power off button to exit volume mode.
Single Pythagorean measurement
The single pythagorean mode calculates indirect measurements
when an obstacle prevents direct measurement. To achieve
accurate results the distances must be at a right angle.
‣ Press the menu button six times to enter single pythagorean
measurement mode. A triangle will appear on the display screen
with one edge flashing.
‣ Press the power on / read button to take the first measurement
from point A (A-B).
‣ Press the power on / read button to take the second
measurement (A-C). This measurement must be taken from the
same point as A-B.
‣ The distance will be calculated automatically (B-C) with results
shown on the display screen.
‣ Press the clear / back / power off button to clear data. Press
and hold the clear / back / power off button to exit single
pythagorean mode.
B
C A
Adding measurements
‣ Press the menu button two times to enter addition mode.
A plus icon will appear on the display screen.
‣ Press the power on / read button to take the first measurement.
‣ Press the power on / read button to take the second
measurement. The values will be added automatically with
results shown on the display screen.
‣ Press the clear / back / power off button to exit addition mode.
Subtracting measurements
‣ Press the menu button three times to enter subtraction mode.
A minus icon will appear on the display screen.
‣ Press the power on / read button to take the first measurement.
‣ Press the power on / read button to take the second
measurement. The values will be subtracted automatically with
results shown on the display screen.
‣ Press the clear / back / power off button to exit subtraction mode.
Double Pythagorean measurement
The double pythagorean mode calculates indirect measurements
when the length is higher and lower than the measurement
position. To achieve accurate results the distances must be at a
right angle.
‣ Press the menu button seven times to enter double pythagorean
measurement mode. A double triangle will appear on the display
screen with one edge flashing.
‣ Press the power on / read button to take the first measurement
from point A (A-B).
‣ Press the power on / read button to take the second
measurement (A-D). This measurement must be taken from
the same point as A-B.
‣ Press the power on / read button to take the third measurement
(A-C). This measurement must be taken from the same point as
A-B and A-D.
‣ The distance will be calculated automatically (B-C) with results
shown on the display screen.
‣ Press the clear / back / power off button to clear data. Press
and hold the clear / back / power off button to exit single
pythagorean mode.
B
C
DA
CARE AND MAINTENANCE
TROUBLE SHOOTING
‣ Inaccurate measurement results may occur in harsh environments
such as strong sunlight, excessive temperature fluctuations, weak
reflective surfaces or low battery.
‣ Whenever possible, store the instrument in a cool, dry place.
Do not store in high temperatures or strong humidity for long
periods of time.
‣ Remove the batteries before storing the device for long periods
of time without use.
‣ To remove dust clean the instrument with a damp, soft cloth.
WARRANTY
The General LM30 comes with a 3 year manufacturers warranty.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Separate to the above Australia Consumer Law, Spot-on
oers a global warranty.
Customer Support
To assist you with any queries or technical questions
please contact the customer support line: 1300 658 338
SPECIFICATIONS
Specications LM30
Product code 70022
Warranty 3 Years
Accuracy ±2mm
Range 0.5 - 30m
Laser class 2 Red
ERR01 Reection
Measure towards an area without reflection interference or
remove the reflecting surface.
ERR02 Out of range
Measurements must be taken within 0.5 - 30m.
ERR03 The target provides poor reection of the laser beam.
Change the target or cover with a piece of white paper.
ERR06 Low battery
Replace the batteries.
www.spoton.com.au
Table des matières
Autres manuels General Instrument de mesure
General
General DLM204 Manuel utilisateur
General
General EP8710 Manuel utilisateur
General
General FD08 Manuel utilisateur
General
General MMH800 Manuel utilisateur
General
General UV512C Manuel utilisateur
General
General MMD900 Manuel utilisateur
General
General P16181HP Manuel utilisateur
General
General MMD4E Manuel utilisateur
General
General XL4 MKII Manuel utilisateur
General
General UV513AB Manuel utilisateur
General
General DLM112SD Manuel utilisateur
General
General MM70 Manuel utilisateur
General
General MMD7NP Manuel utilisateur
General
General RHMG650 Manuel utilisateur
General
General 50-EB-3 Manuel de la liste des pièces
General
General MM1E Manuel utilisateur
General
General DCS1100 Manuel utilisateur
General
General MMD4E Manuel utilisateur
General
General XL1 Manuel utilisateur
General
General MM700D Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur