Gema CM30 Manuel utilisateur

Your global partner for high quality powder coating

CM30 with OptiCenter OC03

Operator

Quick Guide

Switch on the plant V 01/16 CM30 Start-up

Switch on the plant

1. Turn the key switch on 1

2. Touch the screen

3. Log in with user name and password

3.1

3.2

3.3

3.4

CM30 Start-up V 01/16 Switch on the plant

3.5

3.6

4. Referencing axes

5. Select the Coating mode

6. This mask is displayed

Switch on the plant V 01/16 CM30 Start-up

!!Caution!!

In Waste powder mode only fresh powder is used.

There is NO powder recovered!

It is imperative to switch to the Recovery mode after a

certain period!

On the OptiCenter

7. Put the powder bag into the FP cone, place

the cover and insert the FP lance 8. Select the Waste powder mode

9. Confirm the RP hose position

CM30 Start-up V 01/16 Switch off the installation

Switch off the installation

1. Exit the Cleaning mode

2. Press the Standby key

3. Exit Standby

4. Press the Exit key

5. Turn the key switch on 0

Color change / Cleaning mode V 01/20 CM30 Start-up

Color change / Cleaning mode

On the CM30 panel

1. Exit the Coating mode

2. Select the Cleaning mode

3. Close the doors

4. Coarse cleaning of the booth

5. Clean the outside of the guns

(only in case of a foreign booth or if there are

no doors)

CM30 Start-up V 01/16 Color change / Cleaning mode

On the OptiCenter

7. Exit the Coating mode

8. Select the Cleaning mode

9. Select the cleaning possibility

10. Put the fresh powder lance in the park

position

11. Move the FP cone under OptiSpeeder

12. Pres the "Emptying OptiSpeeder" key 2x

Color change / Cleaning mode V 01/16 CM30 Start-up

13. Move back the FP cone

14. Change the recovery hose position

15. Confirm

16. The sequence continues to run

automatically

17. Wait until this mask is displayed

18. Clean the OptiSpeeder, place the cover

CM30 Start-up V 01/16 Color change / Cleaning mode

19. Connect the RP hose to the "Cleaning"

connection

20. Confirm

21. Remove powder bag, clean the OC

thoroughly

22. Fine booth cleaning

23. Clean the ducting

24. Clean and remove the sieve

Color change / Cleaning mode V 01/16 CM30 Start-up

25. Start recovery hose cleaning

26. Clean the cone

27. Clean the cyclone, use only one nozzle at the

time

28. Insert the sieve and close the cyclone

29. Place the bag with new color, connect the RP

hose to the "Waste" connection

30. Exit the Cleaning mode

Ce manuel convient aux modèles suivants

Autres manuels Gema Unité de contrôle

Gema

Gema OptiMove CR07 Mode d’emploi

Gema

Gema OptiStar 4.0 Mode d’emploi

Gema

Gema OptiStar CG08-C Mode d’emploi

Gema

Gema OptiStar 4.0 Mode d’emploi

Gema

Gema OptiCenter OC09 Mode d’emploi

Gema

Gema OptiMove CR08 Mode d’emploi

Gema

Gema MultiStar CG10 Mode d’emploi

Gema

Gema MagicControl 4.0 Manuel utilisateur

Gema

Gema OptiStar CG06 Mode d’emploi

Gema

Gema OptiStar All-in-One Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur