Gefen EXT-DVI-1600HD Manuel utilisateur
www.gefen.com
f
DVI 1600HD
Extender
EXT-DVI-1600HD
User Manual
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hard ware, packaging and
any accompanying doc u men ta tion without prior written notice.
DVI 1600HD Extender is a trademark of Gefen Inc.
© 2008 Gefen Inc., All Rights Reserved
All trademarks are the property of their respective companies
ASKING FOR ASSISTANCE
Rev X2
CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Sender Unit Panel Layout
5 Sender Unit Panel Descriptions
7 Receiver Unit Panel Layout
8 Receiver Unit Panel Descriptions
10 Connecting The DVI 1600HD Extender
11 Connecting And Operating The DVI 1600HD Extender
12 Specifications
13 Warranty
1
Congratulations on your purchase of the DVI 1600HD Extender. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen DVI 1600HD Extender
The Gefen DVI-1600HD is a perfect solution for extending and managing control
systems at great distances. The Gefen DVI-1600HD sends DVI or HDMI, Audio,
and RS232C signals up to 300m away when used with DVI at 1920x1200 and up
to 2km when used with DVI at lower resolutions. It maintains HD video signals
up to 1920x1200 with computers and 1080p with HD equipment. Additionally,
extension of RS232 signals helps create long-distance control systems for AV
integration or touch-panel systems.
How It Works
The Gefen DVI-1600HD system uses a send-and-receive methodology. The DVI/
HDMI/Audio/RS232C source devices are plugged into the Sender module. At
the Receiver, remote devices (including an HD display) plug into the Receiver
module. The proper length of f ber optic cable is connected at both ends. Power
supplies for the modules are plugged into wall sockets and a crisp vibrant HD
picture results.
Note: This device fully supports Display Data Channel (DDC) and High-
Bandwidth Digital Content Protection (HDCP) when the front panel switch on the
sender module is selected to HDMI.
The Gefen DVI-1600HD uses a DVI connector for video. HDMI can be sent by
using adapters or combo cables to provide DVI video with external digital audio
as combined input to the DVI-1600HD Sender unit. The result will be HDMI with
embedded audio at the Receiver end.
The digital input jacks can only support D-PCM or PCM stereo audio formats.
INTRODUCTION
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE DVI 1600HD EXTENDER
• DVI 1600HD Extender uses 4 strands of LC terminated f ber optic cable.
• Single-mode and multi-mode f ber optic cable types are both supported.
• DVI and HDMI modes (for HDCP) are available and are selectable via a
switch located on the front panel of the DVI 1600HD sender unit.
• Analog stereo RCA , digital S/PDIF, and digital TOSLINK inputs are all
available for input but only one is selectable for transmission to the receiver.
The selected audio input will be replicated out of all three audio outputs on
the receiver unit.
• HDMI mode supports HDCP with resolutions up to 1080p Full HD. Both
single and multi-mode cables are supported at distances up to 650 feet (200
meters).
• DVI mode does not support HDCP with resolutions up to 1920 x 1200.
Both single-mode and multi-mode cables are supported. Multi-mode f ber
can support distances of up to 1640 feet. Single-mode f ber can support
distances of up to 6560 feet (2 kilometers).
• HDMI 1.2 compliant.
2
OPERATION NOTES
3
Features
• Pure signal integrity and best image over long distances
• Fiber-optic transmission medium eliminates electromagnetic interference
(EMI) during send or receive operations
• Lightweight, rugged cabling and connectors
• Cost effective per foot/meter
• Low power consumption at 72W total
• Plug and play installation ease -- no software drivers
• Can use both Single and Multimode optical f ber cables
• Maximum range of 2km for DVI, 200m if sending DDC/HDMI with HDCP
• RS232 signal extension helps create long-distance control systems for A/V
integration
Package Includes
(1) Gefen DVI-1600HD Sender
(1) Gefen DVI-1600HD Receiver
(1) 6 Foot DVI Video Cable (M-M)
(1) 6 Foot DB9 RS-232 Cable (M-F)
(1) 12V DC Power Supply
(1) User’s Manual
FEATURES
4
Front Panel
Back Panel
1 2 3 4 5678 910
11 12 17 1813 14 15 16
SENDER UNIT PANEL LAYOUT
5
1 DVI/HDMI Mode Selector Switch
This switch will set the video mode. DVI mode is intended for use with
computers and will support resolutions of up to 1920 x 1200. HDMI mode is for
use with consumer HDMI devices and supports HDCP and resolutions of up to
1080p Full HD. There are also distance limitations associated with the different
modes. Please see page 10 for details.
2 Audio Input Selector Button
This button is used to select the audio input source. There are three input
options: Audio (analog stereo), Coax (digital S/PDIF), Optical (digital TOSLINK).
Each press will cycle through these selections.
3 Audio Selection LED Indicator
This LED will be active when the Audio (analog stereo) audio source has been
selected.
4 Coax Selection LED Indicator
This LED will be active when the Coax (digital S/PDIF) audio source has been
selected.
5 Optical Selection LED Indicator
This LED will be active when the Optical (digital TOSLINK) audio source has
been selected.
6 Reset Button
This button is used to cycle the power off and on. In most cases this will force
the source to re-establish a link with the endpoint device. This will also force the
source to re-read the EDID.
7 Optic B LED Indicator
This LED will indicate the status of the connection between the sender and
receiver’s 2 pair of LC f ber optic cables labeled Optic B. This LED will be active
when a valid link between the sender and receiver has been established.
8 Status LED Indicator
This LED will indicate the status of the unit and will be active when all devices
are properly connected and indicates that the unit is working within specif cation.
9 Optic A LED Indicator
This LED will indicate the status of the connection between the sender and
receiver’s 2 pair of LC f ber optic cables labeled Optic A. This LED will be active
when a valid link between the sender and receiver has been established.
10 Power LED Indicator
This LED will become active once the included 12V DC power supply has been
properly connected between this unit and an available wall power socket.
SENDER UNIT PANEL DESCRIPTIONS
6
SENDER UNIT PANEL DESCRIPTIONS
11 12V DC Power Input
Connect the included 12V DC power supply to this input. The Power LED will
become active when the 12V DC power supply has been properly connected to
the unit and an open wall power socket.
12 Analog Stereo Audio Input
This input will accept analog stereo audio from one pair or RCA audio cables.
This input corresponds to LED labeled Audio on the front panel.
13 S/PDIF Digital Audio Input
This input will accept digital audio from a S/PDIF (coaxial) audio cable. This
input corresponds to LED labeled Coax on the front panel.
14 Optic Digital Audio Input
This input will accept digital audio from a TOSLINK (optical) audio cable. This
input corresponds to LED labeled Optical on the front panel.
15 RS-232 Serial Communications Input
This port is capable of 2-way serial communication between RS-232 devices
connected to the sender and receiver. This port can be connected to a
computers serial communications port for interaction with a RS-232 serial
communications device connected to the receiver.
16 DVI Input
This input will accept a DVI or HDMI (with a HDMI to DVI adapter/cable) source
device.
17 Fiber Optic Input A
This connector accepts a pair of LC terminated f ber optic cable that will link the
sending and receiving unit together. When the cables between this port and the
corresponding ports on the receiver are properly connected, the LED indicator
labeled Optic A on the front panel of both units will become active.
18 Fiber Optic Input B
This connector accepts a pair of LC terminated f ber optic cable that will link the
sending and receiving unit together. When the cables between this port and the
corresponding ports on the receiver are properly connected, the LED indicator
labeled Optic B on the front panel of both units will become active.
7
Front Panel
Back Panel
123 45
6712138 9 10 11
RECEIVER UNIT PANEL LAYOUT
Table des matières
Autres manuels Gefen Extenseur
Gefen
Gefen Toolbox GTB-HDMI-3DTV Manuel utilisateur
Gefen
Gefen DVI RS232 Manuel utilisateur
Gefen
Gefen EXTENDIT CAT5 8000S Manuel utilisateur
Gefen
Gefen EXT-DV- 3600HD Manuel utilisateur
Gefen
Gefen EXT-DVI-CAT5-4X Manuel utilisateur
Gefen
Gefen USB-500 Manuel utilisateur
Gefen
Gefen CAT5-5000 Manuel utilisateur
Gefen
Gefen ex-tend-it DVI Detective Manuel utilisateur
Gefen
Gefen DVI-3000HD Manuel utilisateur
Gefen
Gefen COMPAUD-141 Manuel utilisateur
Gefen
Gefen ADB-100 Manuel utilisateur
Gefen
Gefen GTB-HD-DCS Manuel utilisateur
Gefen
Gefen EXT-COMPAUD-CAT5-142 Manuel utilisateur
Gefen
Gefen EXT-CAT5-1600A Manuel utilisateur
Gefen
Gefen ex-tend-it DVI-CAT5 Manuel utilisateur
Gefen
Gefen HDMIRS232-CAT5 Manuel utilisateur
Gefen
Gefen EXT-DVI-FM2500 Manuel utilisateur
Gefen
Gefen EXT-HDMI1.3-141SBP Manuel utilisateur
Gefen
Gefen EXT-DVI Audio-Cat5 Manuel utilisateur
Gefen
Gefen EXT-DVI-2500HD Manuel utilisateur
