Gefen EXT-DVI-CAT5-4X Manuel utilisateur

DVI CAT5 4X

Extender

USER MANUAL

www.gefen.com

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday thru Friday.

Write To:

Gefen Inc.

c/o Customer Service

20600 Nordhoff St

Chatsworth, CA 91311

[email protected]

www.gefen.com

Notice

Gefen Inc. reserves the right to make changes in the hardware, packaging and

any accompanying documentation without prior written notice.

The EXT-DVI-CAT5-4X is a trademark of Gefen Inc.

ASKING FOR ASSISTANCE

TABLE OF CONTENTS

INTRODUCTION

FEATURES

EXT-DVI-CAT5-4X PANEL DESCRIPTIONS

EXT-DVI-CAT5MSR RECEIVER PANEL DESCRIPTIONS

HOW TO CONNECT AND USE THE EXT-DVI-CAT5-4X

DIP SWITCH USAGE GUIDE

DIP SWITCH DIAGRAM

CAT5 LINK CABLE - WIRING DIAGRAM

EXT-DVI-CAT5-4X RACK MOUNT INSTALLATION

EXT-DVI-CAT5MSR MOUNTING PLATE INSTALLATION

FREQUENTLY ASKED QUESTIONS

TERMINOLOGY

SPECIFICATIONS

WARRANTY

OPERATION NOTES

INTRODUCTION

Thank you for purchasing the DVI CAT5 4X Extender.

The DVI CAT5 4X Extender can extend 4 single link (1920 x 1200) DVI sources

to 4 displays up to 300ft away.

The 4x4 DVI CAT5 Distribution Amplier is the perfect solution for anyone who

needs to send multiple sources to multiple displays in remote locations at the

same time.

The DVI CAT5 4X Extender has 4 DVI single link inputs with 8 (2 per display)

RJ45 output ports. Each pair of CAT5e cables will extend out to a single receiver

with 2 RJ45 inputs and one DVI output port for your display. This will allow you

to extend 4 separate video signals to 4 remote locations.

READ THESE NOTES BEFORE INSTALLING

OR OPERATING THE DVI CAT5 4X Extender

• The DVI CAT5 4X Extender and DVI CAT5 MSR units are housed in a metal

box for better RF shielding.

• Your CAT5e cables should not exceed 300 feet.

• If you do not need DDC or HDCP data you can use a single CAT5e cable for

the video only. The DDC will not be connected. (For further information, see

our Terminology section on page 9.) If HDCP is required, both CAT5e cables

must be used between the sender and receiver units.

• If you are using a single CAT5e cable and the source requires EDID present,

you can use the Gefen DVI Detective to provide EDID information to your

source. The DVI Detective will not transmit HDCP.

• Shielded CAT5e or CAT6 with metal RJ-45 connectors is recommended to

protect from random video ashes caused by EMI.

• Power supply for the receiver should not be connected unless you are using

one CAT5e or going over a distance of 180ft.

• Extensions over 130ft. require you to manually EQ your signal (see page 5).

• Extensions under 130ft. use Auto EQ (which is on by default) (see page 5).

NOTE: The DVI CAT5 4X Extender is fully HDCP compliant

Features:

• Allows 4 DVI single link sources to be extended up to 300ft.

• Maintains resolutions up to 1080p, 2K, and 1920x1200

• Maintains highest DVI single link video resolution

• DVI or HDMI to DVI cables are used to connect the inputs and outputs of the

matrix

INCLUDES:

(1) EXT-DVI-CAT5-4X

(4) EXT-DVI-CAT5MSR

(4) 6 ft DVI to DVI Cable M-M

(1) 24V DC power supply

(4) 5V DC power supply

(1) Rack Ears

FEATURES

EXT-DVI-CAT5-4X SENDER PANEL DESCRIPTIONS

FRONT

BACK

Video 4

RJ45 Outputs

Video 4

DVI Input

Power LED

Video 3

DVI Input

Video 2

DVI Input

Video 1

DVI Input

24V DC Power Input

Video 3

RJ45 Outputs

Video 2

RJ45 Outputs

Video 1

RJ45 Outputs

EXT-DVI-CAT5MSR RECEIVER PANEL DESCRIPTIONS

Connects to DVI display

CAT-5 carries

TMDS signals

CAT-5 carries

DDC/HDCP signals

Connects to 5 volt

power supply

Power Indicator

EQ trim pod

Connect your source(s) to the EXT-DVI-CAT5-4X sender unit's DVI

input(s).

Connect your display(s) to the EXT-DVI-CAT5MSR receiver unit's DVI

output(s).

Connect both CAT5e cables (DDC and Video) between the sender and

the receiver

Plug the 24V power supply into the EXT-DVI-CAT5-4X sender.

If you are not receiving a video signal, follw the steps below to manually

equalize the signal.

HOW TO CONNECT THE EXT-DVI-CAT5-4X

HOW TO USE THE EQ TRIM POT

The EQ trim pot is used extensions over 130 ft. By default, the DVI CAT5

MSR receivers come set to "Auto EQ" (with dip switch 1 ON). Underneath

the receiver is a bank of dip switches hidden by a blank sticker. If you ip dip

switch 1 OFF you can turn off the "Auto EQ" so that you can manually EQ your

signal by using the EQ trim pot on the receiver. If you ip dip switch number

1 to the ON position you can set the DVI CAT5 MSR to "Auto EQ". Auto EQ

works only when the sender is set to "NO BOOST" (see page 6). Auto EQ

works reliably up to 130ft. If you are using the DVI CAT5 MSR beyond any

distance of 130 ft. you will have to manually EQ your signal.

USING THE TRIMPOT

Have both of your CAT5e or CAT6 cables connected.

Start by having the source connected and playing with your display on.

Start with the trimpot turned all the way counter clockwise and slowly turn

the trim pot clockwise until the image stablilizes and displays no noise.

If you still do not get a picture or have video noise, set the sender's to medium

boost and try to re-EQ your signal. If that still does not work try the high boost

setting.

DIP SWITCH GUIDE

The EXT-DVI-CAT5-4X and EXT-DVI-CAT5MSR products both contain a set

of service switches (also called dip switches) located underneath each unit.

The EXT-DVI-CAT5-4X has 4 sets of DIP switches, one for each input, while

the EXT-DVI-CAT5MSR has a single bank of DIP switches. Peeling back the

silver sticker on the bottom of either unit will reveal the DIP switch bank. These

service switches are used to boost and equalize the signal to best match the

conditions in your setup. (*Note: Adjustments should be done with sources

and display on. Switches 3 and 4 are not used.)

Sender Dip Switch Settings

Setting Switch 1 Switch 2

No Boost OFF ON

Normal Boost (Default) OFF OFF

Strong Boost ON OFF

Undened ON ON

Receiver Dip Switch Settings

Setting Switch 1 Switch 2

No EQ (Default) OFF OFF

EQ Setting 2 ON OFF

EQ Setting 3 OFF ON

Maximum EQ ON ON

Adjustment Guidelines:

1) Strong boost should not be used on stranded cables. Strong boosting

will cause pixels or no picture on these cables.

2) Using the wrong settings will not damage the units; it will either

produce no image or a noisy image.

3) To eliminate the possibility of cross talk and interference, cables must

be terminated with 568B scheduling. (See page 7 for details)

DIP SWITCH DIAGRAM

Remove Ta pe

Equalization

Trim Pot

Auto EQ Dip Switches

1432

Boost Dip Switches

Remove Tape

FRONT

EXT-DVI-CAT5MSR

EXT-DVI-CAT5-4X

Autres manuels pour EXT-DVI-CAT5-4X

Table des matières

Autres manuels Gefen Extenseur

Gefen

Gefen EXT-HDTV-CAT5 Manuel utilisateur

Gefen

Gefen EXT-WHD-1080P-SR Manuel utilisateur

Gefen

Gefen ex-tend-it DVI-CAT5 Manuel utilisateur

Gefen

Gefen EXT-DVI-1CAT6 Manuel utilisateur

Gefen

Gefen USB-200 Manuel utilisateur

Gefen

Gefen CAT5-7000 Manuel utilisateur

Gefen

Gefen RS-232 Manuel utilisateur

Gefen

Gefen CAT5-9000HD Manuel utilisateur

Gefen

Gefen EXT-DVIKVM-LAN-L Manuel utilisateur

Gefen

Gefen extendit series CAT5 1000S Manuel utilisateur

Gefen

Gefen EXT-DVI-1CAT6 Manuel utilisateur

Gefen

Gefen CAT5-4000 Manuel utilisateur

Gefen

Gefen EXT-DIGAUD-141 Manuel utilisateur

Gefen

Gefen VGARS232-141 Manuel utilisateur

Gefen

Gefen EXT-DVI-CAT5-ELR Manuel utilisateur

Gefen

Gefen USB 2.0 SR Manuel utilisateur

Gefen

Gefen EXT-VGA-AUDIO-141 Manuel utilisateur

Gefen

Gefen GTV-HDBT-CAT5 Manuel utilisateur

Gefen

Gefen DVI-2000HD Manuel utilisateur

Gefen

Gefen GTB-UHD2IRS-ELRPOL-BLK Manuel utilisateur

Gefen

Gefen EXT-DVIKVM-ELR Manuel utilisateur

Gefen

Gefen EXT-DVI-2CAT6DL Manuel utilisateur

Gefen

Gefen USB-100 Manuel utilisateur

Gefen

Gefen USB2.0-LR Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur