GE "ExecutiveSeries"USB2.0 HO97863 Manuel utilisateur
HO97863
“Executive Series” USB 2.0
7-Port Hub
INSTRUCTION MANUAL
www.jascoproducts.com
2
I. INTRODUCTION...................................3
II. OVERVIEW...........................................4
III. SAFETY INSTRUCTIONS ....................5
IV. POWER MODE SETTING ....................6
V. MOUNTING YOUR HUB.......................7
VI. HARDWARE INSTALLATION ........... 8-9
VII. SOFTWARE INSTALLATION..............10
VIII. TROUBLESHOOTING ........................11
IX. TECHNICAL SPECIFICATIONS .........12
X. FCC COMPLIANCE STATEMENT......13
XI. LIMITED LIFETIME WARRANTY .......14
Table of Contents
3
Congratulations on the purchase of your GE
‘Executive Series’ USB 2.0 7-port Hub! This
GE “Executive Series” Hub will allow you to
receive the maximum possible bandwidth for
all of your USB 2.0 and 1.1 devices!
Please read this entire manual carefully before
using your “Executive Series” Hub. Follow
the instructions to prevent damage to the
“Executive Series” Hub and/or the connecting
devices.
THIS PACKAGE INCLUDES:
• USB 2.0 7-Port Hub
• AC Power Adapter
• USB 2.0 Extension Cable (6 feet)
• Aluminum mounting bracket/stand and
spacer card
• User’s Manual
• Mounting screws
I. Introduction
4
II. Overview
GE Hub technology gives you the best of USB
1.1 and 2.0 in one Hi-Speed USB 2.0 Hub.
Connect USB 2.0 devices for data transfer
rates of up to 480 Mbps. At the same time
connect USB 1.1 devices for a guaranteed
12 Mbps of bandwidth per device. Use any
combination of USB 1.1 and 2.0 devices
– this GE USB Hub will adapt to give you the
greatest bandwidth possible for each device!
FEATURES
• USB 1.1 and 2.0 compatible
• Full speed guaranteed for each USB 1.1 device
• AC adapter supports all high power USB de-
vices
• LED to indicate power
• Mountable with the included bracket/base
• Plug and Play
• Bus fault detection and recovery
• Per port over-current detection and protection
• All downstream ports support high-speed (480
Mbps), full-speed (12 Mbps) and low-speed (1.5
Mbps) operations.
5
III. Safety Instructions
Always read the Safety Instructions carefully.
➢Keep this user’s manual for future
reference.
➢Keep this equipment away from humidity.
➢Do not expose to moisture.
➢Replace if dropped and damaged.
➢Replace if you see obvious signs of
breakage.
➢If you cannot get it to work according
to this User’s Manual refer to the
Troubleshooting section of this manual
(VIII) or contact technical support at
www.jascoproducts.com.
6
IV. Power Mode Setting
There are two power mode options for the GE
“Executive Series” USB 2.0 7-Port Hub.
The rst is self-power mode (recommended),
which requires the use of the AC power
adapter. In this mode, each port is provided
with 500 milliamps, allowing for additional
hubs, cameras and other high-powered
devices.
The second is bus-power mode, which does
NOT require the use of the AC power adapter.
In this mode, the hub is provided with 500
milliamps for all 7 ports. This should be
adequate for mice, keyboards, and other low
power devices. If you are not sure or if device
performance is poor, use the AC adapter.
When using the AC power adapter, make
sure the plug is properly connected to the hub
and to a standard electrical outlet. GE Surge
protection is recommended.
7
An aluminum mounting bracket/base is
provided for mounting your hub. To begin,
choose where you would like the hub located.
V. Mounting Your Hub
Mount the bracket/base using the supplied
screws, slide the spacer insert into the
bracket/base and then slide on the hub for a
snug t.
8
Make sure your computer has all the neces-
sary updates required to support USB. These
can be found on Microsoft’s website.
1. (Optional) Position the Hub as desired
using the directions in Section V.
2. (Optional) Plug the included AC power
adapter into the Power Jack on the side
of the USB 2.0 7-Port Hub. Note: Refer to
Section IV for more details on AC power
adapter use.
VI. Hardware Installation
9
3. (Optional) Plug the AC power adapter
into a standard electrical outlet or GE
Surge Protector (recommended). The
power LED should illuminate. Note: Refer
to Section IV for more details.
4. Plug the A-type connector of the USB 2.0
device cable into the USB port of your
computer. Plug the mini (B) type connec-
tor of the USB cable into the hub.
5. Connect your USB devices to any of the
7 available downstream Ports.
Note: If you connect the hub to a USB 1.1
Port, your computer may warn you that a
high-speed device has been connected
to a non-high speed port. Your hub will
function properly, however it will function
at the USB 1.1 speed of your USB port.
10
Software installation is only required for
Windows®98 and 98 SE users. Users of all
other Operating Systems, including Windows®
NT, ME, 2000, VISTA, XP and any Mac®OS,
may skip this section.
1) Connect the hub to your computer.
2) Windows®98 and 98 SE will detect the
hub and automatically run the “Add New
Hardware Wizard”.
3) When the initial screen appears introducing
the “Add New Hardware Wizard”, click
Next.
4) Select “Search for the best driver for your
device (Recommended): and click Next.
5) When asked to select a location to search
for the drivers, use the default selection. Do
not change the location. Click Next.
6) Click Next to accept the location the driver
will be installed in.
7) On the nal screen notifying you that the
driver has been installed, click Finish.
VII. Software Installation
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels GE Changer
GE
GE T1000 Manuel utilisateur
GE
GE GE-DSG-244 Instructions de montage
GE
GE GBX24 Guide rapide de l'utilisateur
GE
GE Quirky+ Manuel utilisateur
GE
GE 28169 Manuel utilisateur
GE
GE QS24 UR Manuel utilisateur
GE
GE ABB ReliaGear LV SG Manuel utilisateur
GE
GE Digital Energy STS-400-25-3 Manuel utilisateur
GE
GE 15132 Manuel utilisateur
GE
GE Reason H49 Manuel utilisateur
GE
GE Multinet 4 Manuel utilisateur
GE
GE ZTS Series Guide d'installation
GE
GE 40792 Manuel utilisateur
GE
GE 15087 Manuel utilisateur
GE
GE GEH-4763 Manuel utilisateur
GE
GE CWLSWDMBWF1 Manuel utilisateur
GE
GE 15350 Manuel utilisateur
GE
GE Power Break Manuel utilisateur
GE
GE POWER/VAC 4.16 Manuel utilisateur
GE
GE CWLSWDMBWF1 Manuel utilisateur
