GE Concord Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels GE Système de sécurité

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur

Concord/Express

quick reference guide

1. Set your alarm when leaving home (motion detectors ON):

a. Close doors and windows until no zones show open.

b. Press AWAY (3) + User Code.

c. Red “ARMED” light will turn on. Exit the premises within 60 seconds.

2. Disarm the system (or cancel an accidental alarm):

a. Keypad will beep. You have 30 seconds to disarm.

b. Press OFF (1) + User Code.

3. Set the alarm when at home with a delay (motion detectors OFF):

a. Close doors and windows until no zones show open.

b. Press STAY (2) + User Code.

c. Red “ARMED” light will turn on.

4. Disarm before opening doors:

a. Press OFF (1) + User Code.

5. Set the alarm when at home with no delay (motion detectors OFF):

a. Close doors and windows until no zones show open.

b. Press STAY (2) + User Code + Press NO DELAY (4) button.

c. Red “ARMED” light will turn on.

6. If an alarm has been triggered:

a. Before proceeding, verify that the alarm was triggered accidentally. If you

aren’t sure, wait for the phone call from central station.

b. If accidental, press OFF (1) + User Code. This will silence the alarm and cancel

dispatch.

Continued on Back

7. Turn the door chime on or off:

a. Press CHIME (7) + 1.

b. You will hear three beeps if enabled, one beep if disabled.

c. 8. Check system status:

d. Press * for short status

e. Press * * for long status

f. To change your four-digit Master Code:

g. Press 9 then the four digit master code

h. It will say TIME and DATE

i. Press the down arrow or 8 button until it says USER CODES

j. Press#

k. Press the down arrow or 8 button until it says SYSTEM MASTER CODE

l. Press#

m. Enter the new four digit MASTER CODE

n. Press#

o. Press * until it says USER CODES again

p. Press the up arrow or A button until it says EXIT PROGRAMMING READY

q. Press#

The manufacturer of your security system recommends that you test it weekly to

ensure that the system is communicating fully with the Monitoring Station in the event

that an alarm is triggered. If for any reason you feel your security system is not

functioning properly, do not hesitate to call our office at 770-963-0305. We have

technicians available to assist you twenty-four hours per day.