GE AL-1291 Point ID Manuel utilisateur

imagination at work

Security

AL-1291 Point ID DGP

Installation Manual

This document may not be copied in whole or in part, or otherwise reproduced except as

specifically permitted under US copyright law, without the prior written consent from GE.

Document number/revision: 1051832A.

Disclaimer The information in this document is subject to change without notice. GE, in keeping pace

with technological advances, is a company of product innovation. Therefore, it is difficult to

ensure that all information provided is entirely accurate and up-to-date. GE accepts no

responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses,

or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or

application of any of the contents of this document.

This publication may contain examples of screen captures and reports used in daily

operations. Examples may include fictitious names of individuals and companies. Any

similarity to names and addresses of actual businesses or persons is entirely coincidental.

Trademarks and patents GE and the GE monogram are registered trademarks of General Electric.

Other trade names used in this document may be trademarks or registered trademarks of

the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose for which it was designed; refer to the data sheet and

user documentation. For the latest product information, contact your GE sales

representative or visit us online at www.gesecurity.com.

FCC compliance This device complies with Part 15 of the DFCC rules. Operation is subject to the following

three conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may

cause undesired operation.

3. Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Contact Direct all inquiries about GE’s legal policies with regard to this product to:

Director of Legal Services

GE SecurityDirector of Legal Services

12345 SW Leveton Drive

Tualatin, OR 97062 USA

Introduction

This is the GE AL-1291 Point ID DGP Installation Manual. This document includes an overview of the

product and detailed instructions explaining:

• how to install the hardware; and

• how to do basic programming.

There is also information describing how to contact technical support if you have questions or concerns.

To use this document effectively, you should have the following minimum qualifications:

• a basic knowledge of the Alliance system; and

• a basic knowledge of electrical wiring and low-voltage electrical connections.

Read these instructions and all ancillary documentation entirely before installing or operating this product.

The most current versions of this and related documentation may be found on our website. Refer to Online

publication library on page 20 for instructions on accessing our online publication library.

Note: A qualified service person, complying with all applicable codes, should perform whatever hardware installation is

required.

Conventions used in this document

The following conventions are used in this document:

Safety terms and symbols

These terms may appear in this manual:

Cautions identify conditions or practices that may result in damage to the equipment or other property.

Warnings identify conditions or practices that could result in equipment damage or serious personal injury.

Bold Menu items, buttons, and keys.

Italic Titles of books and various documents.

Emphasis of an instruction or point; special terms

Windows, panes, tabs, fields, variables, and other GUI elements.

Monospace Text that displays on the keypad screen.

File names, path names, or coding sequences.

Blue italic Hyperlinks to cross-references, related topics, and URL addresses.

CAUTION

Improper use may cause equipment damage.

WARNING

Improper use could cause equipment damage or serious personal injury.

AL-1291 Point ID DGP

Installation Manual

Overview

The AL-1291 Point ID DGP (data gathering panel) is an interface between the Alliance system data bus and a

point ID data bus. The DGP provides two-wire bidirectional communication with up to 32 individually

addressed point ID devices. The system bus supports up to 15 DGPs at a distance of up to 5,000 feet (1.5 km)

from the control panel.

Product contents

Each AL-1291 Point ID DGP ships with the following:

• 2 three-position terminal blocks

• 1 four-position terminal block

• 4 clip-in standoffs

• 4 mounting screws

Inspect the package and contents for visible damage. If any components are damaged or missing, do not use

the unit; contact the supplier immediately. If the unit needs to be returned, it must be shipped in the original

box.

Other required equipment

You will also need a DVM (digital volt meter).

Installation

Mount the DGP in any existing Alliance enclosure.

To install the unit, do the following:

1. Slide the terminal blocks together (Figure 1).

Figure 1. Slide terminal blocks together

2. Slide the terminal blocks over the pins on the board (Figure 2).

Figure 2. Exploded view

CAUTION

You must be free of static electricity before handling circuit boards. Wear a grounding strap or touch a

bare metal surface to discharge static electricity.

DIP switches

CON 1,

COMMS/TAMP

terminal block

CON 2,

point ID

terminal block

CON 10, EARTH

LEDs

AL-1291 Point ID DGP

Installation Manual

3. The DIP switches on the DGP (Figure 2) are used to identify the DGP address (from 1 to 15) to the

Alliance control panel. Set the DIP switches for the appropriate address, as shown in Figure 3.

Figure 3. DGP address DIP switch settings

4. Mount the DGP in the enclosure using four clip-in standoffs and mounting screws.

5. Wire the unit to the system data bus and to point ID devices (see Wiring on page 7).

1 2 3 4

DGP 1

1 2 3 4

DGP 2

1 2 3 4

DGP 3

1 2 3 4

DGP 4

1 2 3 4

DGP 5

1 2 3 4

DGP 6

1 2 3 4

DGP 7

1 2 3 4

DGP 8

1 2 3 4

DGP 9

1 2 3 4

DGP 10

1 2 3 4

DGP 11

1 2 3 4

DGP 12

1 2 3 4

DGP 13

1 2 3 4

DGP 14

1 2 3 4

DGP 15

1 2 3 4

ON Sample

DIP switch 1 is set to on,

DIP switches 2, 3, and 4 are set to off

Wiring

Wire the DGP terminals as shown in Figure 4. Earth wires from all pieces of equipment must be grounded at

one system earth. For more information on grounding details, refer to the Alliance control panel’s installation

instructions.

Figure 4. Wiring diagram

Table 1 shows the DGP wiring terminal details.

DGP to Alliance control panel wiring restrictions

You can locate the DGP up to 5,000 feet (1.5 km) from the Alliance control panel. The DGP must be connected

via a 2-pair twisted, shielded data cable from the system bus connection. We recommend you use Belden

8723.

Where the DGP power supply source is at a distance greater than 328 feet (100 m), you must use an external

supply. We recommend a supply output of 13.8 VDC 1 A fused.

Table 1. Wiring terminals

Connector Category Terminals Description

CON 1 COMMS +, - 12 VDC power supply.

D+, D- Positive and negative connection of the system bus.

TAMP Ti, Tc Connect the enclosure tamper switch across these terminals. Requires closed loop

tamper switch.

CON 2 PID +, - 9.9 to 13.2 VDC power supply.

1234

D+

D-

CON 2

CON 1

JP1 TERM

JP2 LRN

AL-1291 Point ID DGP

Installation Manual

DGP to point ID devices wiring restrictions

Connection to all point ID devices requires one + and one - terminal to provide power and data transmission.

Point ID devices provide for one or two bus terminals and can be connected in a single loop or in a multidrop

configuration (Figure 5). The bus loop does not need special termination.

Figure 5. Multidrop configuration

Table 2 shows the point ID bus load limits.

LEDs

The two LEDs (Figure 2 on page 5) on the DGP indicate polling status as follows:

RX. The RX LED flashes to indicate polling data is being received by the point ID DGP from the

Alliance control panel. If the RX LED does not flash, the DGP is not operational or the system bus

is faulty. Check the cabling.

TX. The TX LED flashes to indicate the point ID DGP is replying to polling from the Alliance control

panel. If the RX LED flashes, but the TX LED does not flash, the DGP is not programmed to be

polled in the control panel or the DGP is not addressed correctly.

Table 2. Load limits

Maximum number of point ID devices per point ID bus length

Wire gauge (AWG) 1000 feet (305 m) 2500 feet (762 m) 5000 feet (1524 m)

22 32 20 16

20 32 32 20

18 or less 32 32 32

- + - + - - + +

AL-1291 Point ID DGPPoint ID devicePoint ID devicePoint ID device

Jumpers

Use the two jumpers (Figure 4 on page 7) on the DGP as follows:

TERM (JP1). Fit the JP1 jumper on the DGP if the DGP is the last device on the control panel system

bus.

LRN (JP2). Short the JP2 jumper for two seconds to start learn mode and enable the DGP to

recognize (learn) point ID devices.

Point ID device address settings

The point ID device address settings are directly linked to the zone number the device will have on the DGP

(Table 3). The address numbering starts at 0.

The 4I4O point ID devices require eight zone numbers per device. Be sure to take the 8-zone

requirement into account when addressing the 4I4O devices. For example, if a 4I4O device is the first

device you add to point ID DGP 1, it will be address 0 and the next device you add will be address 8.

Table 3. Device addresses and related zone numbers

DGP Zones Point ID address DGP Zones Point ID address

Control panel 1 to 16 None DGP 8 129 to 144 0 to 15

DGP 1 17 to 32 0 to 15 DGP 9 145 to 160 0 to 15

DGP 2 33 to 48 0 to 15 DGP 10 161 to 176 0 to 15

DGP 3 49 to 64 0 to 15 DGP 11 177 to 192 0 to 15

DGP 4 65 to 80 0 to 15 DGP 12 193 to 208 0 to 15

DGP 5 81 to 96 0 to 15 DGP 13 209 to 223 0 to 15

DGP 6 97 to 112 0 to 15 DGP 14 225 to 240 0 to 15

DGP 7 113 to 128 0 to 15 DGP 15 241 to 256 0 to 15

AL-1291 Point ID DGP

Installation Manual

Use the DIP switches (Figure 6) located on each point ID device to set the device addresses.

Figure 6. DIP switch settings for point ID device addresses

1 2 3 4 5 6 7 8

Point ID device 0

1 2 3 4 5 6 7 8

Point ID device 1

1 2 3 4 5 6 7 8

Point ID device 2

1 2 3 4 5 6 7 8

Point ID device 3

1 2 3 4 5 6 7 8

Point ID device 4

1 2 3 4 5 6 7 8

Point ID device 5

1 2 3 4 5 6 7 8

Point ID device 6

1 2 3 4 5 6 7 8

Point ID device 7

1 2 3 4 5 6 7 8

Point ID device 8

1 2 3 4 5 6 7 8

Point ID device 9

1 2 3 4 5 6 7 8

Point ID device 10

1 2 3 4 5 6 7 8

Point ID device 11

1 2 3 4 5 6 7 8

Point ID device 12

1 2 3 4 5 6 7 8

Point ID device 13

1 2 3 4 5 6 7 8

Point ID device 14

1 2 3 4 5 6 7 8

Point ID device 15

1 2 3 4 5 6 7 8

Point ID device 16

1 2 3 4 5 6 7 8

Point ID device 17

1 2 3 4 5 6 7 8

Point ID device 18

1 2 3 4 5 6 7 8

Point ID device 19

1 2 3 4 5 6 7 8

Point ID device 20

1 2 3 4 5 6 7 8

Point ID device 21

1 2 3 4 5 6 7 8

Point ID device 22

1 2 3 4 5 6 7 8

Point ID device 23

1 2 3 4 5 6 7 8

Point ID device 24

1 2 3 4 5 6 7 8

Point ID device 25

1 2 3 4 5 6 7 8

Point ID device 26

1 2 3 4 5 6 7 8

Point ID device 27

1 2 3 4 5 6 7 8

Point ID device 28

1 2 3 4 5 6 7 8

Point ID device 29

1 2 3 4 5 6 7 8

Point ID device 30

1 2 3 4 5 6 7 8

Point ID device 31

1 2 3 4 5 6 7 8

ON Sample

DIP switch 1 is set to on,

2 - 8 are set to off

Table des matières

Autres manuels GE Système de sécurité

GE 610 Manuel utilisateur

GE ActiveKEY Manuel utilisateur

GE NetworX V3 Manuel utilisateur

GE 1200 Series Manuel utilisateur

GE DeluxeDoorAlarm Manuel utilisateur

GE 45236 Manuel utilisateur

GE 45235 Manuel utilisateur

GE 600-1021-95R Manuel utilisateur

GE Simon XTi Manuel utilisateur

GE 60-362 Manuel utilisateur

GE GEC-4VDPC Instructions de montage

GE SmartCom CC-SCRS01 Manuel utilisateur

GE 13-949 Manuel utilisateur

GE TX-6310-01-1 b Manuel utilisateur

GE VT71230-R3 Guide d'installation

GE Euro Simon Manuel utilisateur

GE Concord 4 Manuel utilisateur

GE 45411 Manuel utilisateur

GE Concord express Manuel utilisateur

GE Security Pro 500 Manuel utilisateur

GE Security Pro 7000 Manuel utilisateur

GE 45131 Manuel utilisateur

GE Silent Alert 45137 Manuel utilisateur

GE NX-108E - Security NetworX NX-4 System Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur