GE JGGN24 Manuel utilisateur

Questions? Call 866.GE.GRILL (866.434.7455)

or Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Assembly Outdoor Cooking

Instructions Center

Read these instructions completely and carefully.

•IMPORTANT –Observe all

governing codes and ordinances.

•Note to Assembler –Be sure to leave these

instructions with the Consumer.

•Note to Consumer –Keep these

instructions for future reference.

•Skill level – Assembly of this grill requires basic

mechanical skills.

BEFORE YOU BEGIN

•Proper assembly is the responsibility of the assembler.

•Product failure due to improper assembly is not

covered under the Warranty.

•If you received a damaged grill, you should contact

your dealer.

•Note –Grill must be completely assembled before

any gas connections are made.

TOOLS YOU WILL NEED

Phillips screwdriver

7/16″open end wrench or deep socket with extension

Rubber mallet (optional)

JGGN24, JGGR24

Block of wood or cardboard

(optional)

Assembly Instructions

PARTS INCLUDED (Not all models have all parts)

Wheel Axle Bolt (2)

Thumb Screw (2)

Large Bolt (8)

Large Wheel Washer (2)

Wheel Clip (2)

Wheel (2)

Wing Nut (19)

Handle Bolt (2)

Handle Nut (2)Base Assembly (1)

Rotisserie Burner (1)

(On some models)

Retractable Shelf (1)

Side-by-side Grids (2)

LP Tank Bracket (1)

Small Bolt (1)

(For LP Tank Bracket)

Small Washer (1)

(For LP Tank Bracket)

Upper Rear Brace (1)

Front Banner (1)

Side Grid (1)

Left Side Burner/Shelf (1) Side Shelf (1 or 2)

Bin (1)

Grease Cup

Holder (1)

Flav-R-Wave®* (1)

Grill Body (1)

Handle with

Spacer (2)

Shelf Handle (1)

Screw (2)

(Depending on model)

Carriage Bolt (2)

*Flav-R-Wave®is a registered trademark of Onward Multi-Corp, Inc.

•Carefully cut open the box, remove the contents

and group like parts together.

UNPACK THE GRILL

Assembly Instructions

4. Grasp the pan on both sides and raise it up until

the legs are standing squarely on the floor.

To aid assembly, all parts in bold type in the following

assembly steps match the illustrations shown in the

PARTS INCLUDED section.

NOTE TO ASSEMBLER

1. Make sure the open side of the pan in the base

assembly is facing up.

2. Lift up on the right side of the pan.

3. Lift the left ends of the legs and swing them over

the wheels to lay flat on the floor.

UNFOLD THE BASE ASSEMBLY

RIGHT

SIDE

LEFT

SIDE

Casters should

be on the

right top side

Pan

3. Slide a wheel axle bolt through a wheel, large wheel

washer, and through the top hole on the left leg.

Secure the wheel in place by sliding a wheel clip

through the hole in the wheel axle bolt. Repeat for

the other leg.

1. Thread a thumb screw into each of the lower holes

on the right side and through the pan. Secure them

in place with wing nuts.

2. Insert a carriage bolt into each of the center holes

on the left side and through the pan. Secure them

in place with wing nuts.

ASSEMBLE THE LOWER BASE

Carriage

Bolt

RIGHT

SIDE

LEFT

SIDE

Assembly Instructions

Wheel Axle Bolt (2)

Thumb Screw (2)

Wing Nut (4)

Large Wheel Washer (2)

Wheel Clip (2)

Wheel

Axle Bolt

Wheel

Large

Wheel

Washer

Wheel Clip

Wing

Nut

RIGHT

SIDE

LEFT

SIDE Thumb

Screw

Wing

Nut

Carriage Bolt (2)

Pan

1. Turn the grill body upside-down and wedge

cardboard or a block of wood under the front side

to prevent tipping during assembly.

2. Slide the bolt on each of the back legs into the

slots on the back ends of the grill. Secure in place

with wing nuts.

3. Hook the two bolts in the front legs into the holes

on the front ends of the grill. Secure in place with

wing nuts.

ASSEMBLE BASE TO GRILL BODY

Wing

Nuts

Wing

Nuts

Assembly Instructions

4. Thread a large bolt into the front bottom hole on

each side. Secure in place with wing nuts.

5. Position the upper rear brace between the upper

back legs and secure it to the legs at each end with

two large bolts and wing nuts.

Wing

Nuts

Upper

Rear

Brace Large

Bolts

Large Bolt (6)

Wing Nut (10)

1. Lower the wheels toward you and rest the back legs

on the floor.

2. From the back top side of the grill, lift the grill

onto its wheels.

SET THE GRILL ON ITS WHEELS

BACK OF

GRILL

Block of

wood or

cardboard

BACK OF

GRILL

Block of

wood or

cardboard

BACK OF GRILL

FRONT OF

GRILL

BACK OF GRILL

Large Bolts

NOTE: If your model has a burner/shelf, it must be

installed on the left side.

1. Peel off the protective shipping film from the side

shelves, if present.

2. Hook the bottom slotted holes of the shelf onto

the lower bolt heads. Repeat for the other shelf

on the other side.

3. If desired, raise the shelf and hook it in the up

position. It may also be locked in the up position

by inserting a large bolt in the center back hole

and securing it with a wing nut.

INSTALL THE SIDE SHELVES

Assembly Instructions

•Slide a handle bolt through a handle and spacer

and into the hole in the grill top. Align and tighten

in place with a handle nut using a 7/16″open end

wrench or deep socket. Repeat for the other side.

INSTALL THE HANDLES

•Hook the bottom holes of the front bin onto the

bottom bolt heads on both sides and lock it down

into the neck of the keyhole slot.

INSTALL THE FRONT BIN

Keyhole

Slot

Handle

Nut

Spacer

Handle

Bolt

Handle Bolt (2) Handle Nut (2)

Large Bolt (1 or 2) Wing Nut (1 or 2)

Wing Nut

Back

Hook on

bottom bolt

Back

Hook on bottom

bolt in slot

Large Bolt

4. Remove the side grid and peel off the protective

shipping film, if present. Guide the two pins on the

grid into the two holes in the side burner/shelf and

lower it into position.

5. The shelf should be locked in the up position by

inserting a large bolt in the center back hole and

securing it with a wing nut.

Assembly Instructions

1. Peel off the protective shipping film from the side

shelves, if present.

2. Hook the bottom slotted holes of the burner/shelf

onto the lower bolt heads. Raise the shelf and hook

it in the up position.

3. Peel off the protective shipping film from the

burner shelf door and burner area, if present.

Attach the shelf handle with two screws.

INSTALL THE LEFT SIDE

BURNER/SHELF (on some models)

Screw (2)

Large Bolt (1) Wing Nut (1)

Shelf

Handle

Screws

Side

Grid

Wing

Nut

Large

Bolt

Hook on

bottom bolt

Back

Hook on bottom

bolt in slot

Back

1. Connect the side burner hose by pressing the

fitting onto the side burner gas tube.

2. Pull the side burner hose into the neck of the

keyhole bracket and hand-tighten the nut to

lock in place.

Assembly Instructions

CONNECT THE LEFT SIDE

BURNER/SHELF (on some models)

Side Burner

Gas Tube

Side Burner

Hose Fitting

Make side burner

gas connection

Pull side

burner hose

fitting into

neck

3. Hand connect the side burner electrode wire to

the connector under the control panel.

(The connector is under the control panel,

on the stem of the red igniter button).

Make a firm

connection

1. Place the Flav-R-Wave® on the supports in the

bottom of the grill. The Flav-R-Wave® should lie flat.

2. Place the side-by-side grids on the front and back

supports*.

ASSEMBLE THE GRILL

COMPARTMENT

Assembly Instructions

3. With the deflector on top (holes facing front),

press the round end of the rotisserie burner (on

some models) into the hole on the right. Press

down and snap the left side into the two holes in

the left side of the grill.

4. Hook the back feet of the retractable shelf into the

holes in the lid. Place the swivel feet in the small

back notches in the grill sides.

Side-by Side

grids

Retractable

Shelf

Flav-R-Wave®

Rotissere

burner

* See the Owner’s Manual for available grid

positions for your model.

1. Insert the pointed support of the front banner into

the slot behind the front leg at the base.

2. Snap the upper support button into the hole in the

back of the leg. Use a rubber mallet, if needed.

Repeat on the opposite side.

INSTALL THE FRONT BANNER

Assembly Instructions

1. Under the left shelf, insert the small bolt from the

inside through the square hole in the side support.

2. Attach the LP tank bracket to the side support with

the small washer and a wing nut.

ATTACH THE LP TANK BRACKET

•Your grill is designed

to be used with an LP

gas tank equipped

with the new QCC-1

Quick Closing

Coupling system

and the new

OPD handwheel.

•The QCC-1 system

is recognizable by

the external threads

on the inlet port of

the valve.

•The OPD handwheel

is recognizable by its

shape as shown.

•The LP gas tank used with this grill must NOT have

a capacity larger than 20 lbs. (9kg).

•Approximately:18″(46 cm) high

12″(31 cm) diameter

•These tanks are available from your local gas

grill dealer.

•WARNING:Make sure that the

cylinder valve on the LP tank is closed. Close

by turning clockwise.

1. Place the LP tank on the grill base with the LP tank

connector facing to the front of the grill. Slide the

LP tank bracket over the inner rim of the LP tank.

2. Tighten the wing nut on the LP tank bracket to

lock the LP tank in position.

MOUNT THE LP TANK

(not included—obtain locally)

LP Tank

Bracket

Wing Nut

and Small

Washer

Small Bolt

Wing Nut (1)

Small Bolt (1) Small Washer (1)

QCC1¤

NEW OPD

HANDWHEEL

LP tank

valve

Autres manuels pour JGGN24

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GE Gril

GE Monogram ZGG36N31YSS Instructions d'utilisation

GE Monogram ZGG48N42CSS Guide de l'utilisateur

GE ZX48CTACSS Manuel utilisateur

GE 106811 Manuel utilisateur

GE OCFLA-2150 Manuel utilisateur

GE ZGG27N21CSS Manuel utilisateur

GE Monogram ZGG420LBPSS Manuel utilisateur

GE Monogram ZGG48N31CSS Guide de l'utilisateur

GE 106796 Manuel utilisateur

GE ZGG542LCPSS Manuel utilisateur

GE Monogram ZGG420LBPSS Manuel utilisateur

GE jp380bvbb Manuel utilisateur

GE Monogram ZX36CTYSS Manuel utilisateur

GE 169015 Manuel utilisateur

GE 169039 Manuel utilisateur

GE Monogram ZX27CTYSS Manuel utilisateur

GE Monogram ZGG36L21CSS Guide de l'utilisateur

GE JP380 Manuel de formation

GE Monogram ZGG24L Manuel utilisateur

GE 106642 Manuel utilisateur

GE 169148 Manuel utilisateur

GE ZGG300LCPSS Manuel utilisateur

GE JGGN24 Manuel utilisateur

GE Profile 24 CustomStyle Manuel utilisateur

Manuels Gril populaires d'autres marques

Orbegozo

Orbegozo GR 2300 Manuel utilisateur

bora

bora PT11 Manuel utilisateur

Klarstein

Klarstein 10031664 Manuel utilisateur

Garland

Garland MWE3W Manuel utilisateur

Char-Broil

Char-Broil 463722714 Manuel utilisateur

Nexgrill

Nexgrill 720-0830HK Manuel utilisateur

Kenmore

Kenmore 415.16123800 Manuel utilisateur

Camp Chef

Camp Chef PG24CLAU Manuel utilisateur

Tucker Barbecues

Tucker Barbecues GTR Series Instructions de montage

Monogram

Monogram ZGG540NCP1SS Manuel utilisateur

Equipex

Equipex Sodir Savoy Manuel utilisateur

Gaggenau

Gaggenau VR 414 610 Manuel utilisateur

Miele

Miele KM 408-1 Manuel utilisateur

George Foreman

George Foreman GGR50B Manuel utilisateur

AOG

AOG T series Manuel utilisateur

Gorenje

Gorenje TG2000CB Mode d’emploi

Weber

Weber Genesis Silver-B Permamount NG 051701 Manuel utilisateur

Glen

Glen SA 3037 Manuel utilisateur