GE JGGR27 Manuel utilisateur

Questions? Call 866.GE.GRILL (866.434.7455)

or Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Assembly Outdoor Cooking

Instructions Center

Read these instructions completely and carefully.

•IMPORTANT –Observe all

governing codes and ordinances.

•Note to Assembler –Be sure to leave these

instructions with the Consumer.

•Note to Consumer –Keep these

instructions for future reference.

•Skill level – Assembly of this grill requires basic

mechanical skills.

BEFORE YOU BEGIN

•Proper assembly is the responsibility of the assembler.

•Product failure due to improper assembly is not

covered under the Warranty.

•If you received a damaged grill, you should contact

your dealer.

•Note –Grill must be completely assembled before

any gas connections are made.

TOOLS YOU WILL NEED

Phillips screwdriver

7/16″open end wrench or deep socket with extension

Hammer

JGGB27, JGGN27, JGGR27

Pliers

Block of wood

Assembly Instructions

PARTS INCLUDED (Not all models have all parts)

Handle and Spacer (2)

Lid Hinge Bolt (2)

Side Grid (1)

Handle Bolt (2) Nut (14)

Wheel (2)

Clip (2)

Shelf Handle (1) Screw (2)

Wing Nut (2)

Left Side Burner/Shelf (1) or

Left Side Shelf (1)

(Depending on model)

Lid (1)

Swing Basket (1)

(on some models)

Warming

Rack (1)

Side-by-side

Grid (3)

Flav-R-Wave®* (1)

LP Tank

Retainer (2)

Base Cart (1)

Grill Bottom (1)

Right Shelf (1)

Disposable Aluminum

Drip Pan (1)

Push Nut (2)

Grid Lifter (1)

Large Bolt (2)

Side Panel (2) Front Panel (1) Bolt (6)

Axle Rod (1)

Rotisserie

Burner (1)

(on some models)

*Flav-R-Wave®is a registered trademark of Onward Multi-Corp, Inc.

•Carefully cut open the box, remove

the contents and group like parts together.

UNPACK THE GRILL

Assembly Instructions

1. Hammer a push nut onto the

end of the axle rod.

2. Slide a wheel onto the axle rod.

3. Slide the base

cart onto the

axle rod.

Hammer a

push nut onto

the end of the

axle rod.

ASSEMBLE THE BASE CART

1. Peel off the protective shipping film from the front

panel, if present.

2. Stand the side panels on end with the bolts at the

top. Stand the front panel on end with the cutouts

at the top.

3. Hook the front panel screw heads (4) into the

keyhole slots on the side panels.

4. Push the front panel down so that the screw heads

slide into the lower neck of the keyhole slots.

Tighten the screws to lock the panels in place.

ASSEMBLE THE LOWER BASE

Push nut

Wheel

(outside

of wheel

against

push nut)

Side

panels

Front

panel

To aid assembly, all parts in bold type in the following

assembly steps match the illustrations shown in the

PARTS INCLUDED section.

NOTE TO ASSEMBLER

Push nut

Axle rod

Push Nut (2)

Cutouts

at top

Bolts

at top

Wheel (outside

of wheel against

push nut)

Block of

wood as

protective

base

Block of

wood as

protective

base

Base cart

Axle rod

Side

panels Front

panel

Cutouts

at top

Bolts

at top

Tighten screws

Side

panel

Front

panel

Assembly Instructions

1. Place the grill bottom upside down on the floor

and position the hoses as shown.

2. Turn the assembled lower base over and slide it

over the six bolts in the grill bottom. Secure in

place with six nuts.

3. Insert a Phillips screwdriver through each angled

hole and make sure the bolts are tight.

MOUNT THE BASE TO THE

GRILL BOTTOM

1. Place the base cart over the lower base.

2. Insert six bolts from inside the lower base and

secure in place with six nuts.

MOUNT THE BASE CART

Side burner hose

LP tank hose

Nut (6)

Nut (6) Bolt (6)

Front

Back

Front

Back

Nuts

Bolts

Nuts

Bolts

Back

Side-burner

hose

Align side-burner

hose with U-shaped

cut-out on base

Assembly Instructions

NOTE: If your model has a burner/shelf, it must be

installed on the left side.

1. Peel off the protective shipping film from the side

shelves, if present.

2. Hook the bottom slotted holes of the shelf onto the

bottom bolt heads. Repeat for other shelf on the

other side.

3. If desired, raise the shelf and hook it in the up

position. It may also be locked in the up position

by inserting a large bolt in the center back hole

and securing it with a wing nut.

INSTALL THE SIDE SHELVES

1. From the back side, lower the base to the floor.

2. From the back top side of the grill, lift the grill

onto its wheels.

SET THE GRILL ON ITS WHEELS

Large bolt

Wing nut

Back

Front

Wing Nut (1 or 2)

Large Bolt (1 or 2)

Front

Hook on

bottom bolt

Back

Front

Hook on

bottom bolt

in slot

1. Hook the bottom slotted holes of the burner/shelf

onto the bottom bolt heads. Raise the shelf and

hook it in the up position.

2. Peel off the protective shipping film from the

burner shelf door and burner area, if present.

Attach the shelf handle with two screws.

INSTALL THE LEFT SIDE

BURNER/SHELF (on some models)

Assembly Instructions

3. Remove the side grid and peel off the protective

shipping film, if present. Guide the two pins on the

side grid into the two holes in the side

burner/shelf and lower it into position.

4. The shelf should be locked in the up position by

inserting a large bolt in the center back hole and

securing it with a wing nut.

Shelf

handle

Screws

Side burner grid

Large

bolt

Wing nut

Screw (2)

Wing Nut (1)

Large Bolt (1)

Back

Front

Back

Hook on

bottom bolt

Hook on

bottom bolt

in slot

1. Connect the side burner hose by pressing the

fitting into the side burner gas tube.

2. Pull the side burner hose fitting into the neck of

the keyhole bracket and hand-tighten the nut to

lock in place.

Assembly Instructions

CONNECT THE LEFT SIDE

BURNER/SHELF (on some models)

93. Connect the side burner electrode wire to

the connector under the control panel. (The

connector is under the control panel, on the

stem of the red igniter button).

Side burner

gas tube

Side burner

hose fitting

Make side burner

gas connection

Pull side

burner hose

fitting into

neck

Make a firm

connection

Assembly Instructions

1. Place and align the lid over the grill bottom in the

closed position.

2. Insert a lid hinge bolt into each hinge.

3. Open the lid and insert a clip through the hole in

each lid bolt.

INSTALL THE LID

•Slide a handle bolt through a handle and spacer

and into the hole in the grill lid. Align and secure

in place with a nut using a 7/16″open-end wrench

or a deep socket. Repeat on the other side.

INSTALL THE HANDLES

Lid hinge

bolt

Clip

Lid Hinge Bolt (2) Clip (2) Handle Bolt (2) Nut (2)

Front

Nut

Handle

spacer

Handle

bolt

1. Place the Flav-R-Wave® on the supports in the

bottom of the grill. The Flav-R-Wave® should

lie flat.

2. Place the side-by-side grids on the front and

back supports*.

ASSEMBLE THE GRILL

COMPARTMENT

Flav-R-Wave®

Grids

Assembly Instructions

3. Place the ends of the warming rack into the back

slots on the upper grill sides.

4. Hang the swing basket (on some models) on the

two hooks in the lid.

Warming

rack

Swing

basket

* See the Owner’s Manual for available grid positions

for your model.

•Place the end of the LP tank retainer in the hole

in the base. Flex the retainer and place the other

end in the other hole in the base. Repeat for the

other side.

ATTACH THE LP TANK RETAINERS

•Your grill is designed

to be used with an LP

gas tank equipped

with the new QCC-1

Quick Closing

Coupling system

and the new

OPD handwheel.

•The QCC-1 system

is recognizable by

the external threads

on the inlet port of

the valve.

•The OPD handwheel

is recognizable by its

shape as shown.

•The LP gas tank used with this grill must NOT have

a capacity larger than 20 lbs. (9kg).

•Approximately: 18″(46 cm) high

12″(31 cm) diameter

•These tanks are available from your local gas

grill dealer.

WARNING: Make sure that the cylinder

valve on the LP tank is closed.

Close by turning clockwise.

1. Place the LP tank on the grill base with the LP tank

connector facing to the right of the grill.

2. Center the LP tank and lower the retainers into

place around it.

MOUNT THE LP TANK

(not included—obtain locally)

Assembly Instructions

LP tank

retainer

Right side

Back of grill

QCC1¤

NEW OPD

HANDWHEEL

LP tank

valve

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GE Gril

GE Monogram ZGG24L Manuel utilisateur

GE Monogram ZGG48N42 Manuel utilisateur

GE Monogram ZGG24L20 Manuel utilisateur

GE Monogram ZGG420LBPSS Manuel utilisateur

GE JGHC60GEN Manuel utilisateur

GE ZGG420LCPSS Manuel utilisateur

GE 169110 Manuel utilisateur

GE JTP85 Manuel utilisateur

GE 169232 Manuel utilisateur

GE ZGG27N21CSS Manuel utilisateur

GE ZX48CTACSS Manuel utilisateur

GE Profile PT970 Manuel utilisateur

GE Professional Outdoor Grills and Cooktop Manuel utilisateur

GE ZGG300LCPSS Manuel utilisateur

GE 169044 Manuel utilisateur

GE 106621 Manuel utilisateur

GE Monogram ZX36CTYSS Manuel utilisateur

GE Monogram ZGG540NBPSS Manuel

GE Monogram ZX27CTYSS Manuel utilisateur

GE Monogram ZGG300LB Manuel utilisateur

GE 106642 Manuel utilisateur

GE Monogram ZGG48L31CSS Manuel utilisateur

GE 106668 Manuel utilisateur

GE JGGN24 Manuel utilisateur

Manuels Gril populaires d'autres marques

Orbegozo

Orbegozo GR 2300 Manuel utilisateur

bora

bora PT11 Manuel utilisateur

Klarstein

Klarstein 10031664 Manuel utilisateur

Garland

Garland MWE3W Manuel utilisateur

Char-Broil

Char-Broil 463722714 Manuel utilisateur

Nexgrill

Nexgrill 720-0830HK Manuel utilisateur

Kenmore

Kenmore 415.16123800 Manuel utilisateur

Camp Chef

Camp Chef PG24CLAU Manuel utilisateur

Tucker Barbecues

Tucker Barbecues GTR Series Instructions de montage

Monogram

Monogram ZGG540NCP1SS Manuel utilisateur

Equipex

Equipex Sodir Savoy Manuel utilisateur

Gaggenau

Gaggenau VR 414 610 Manuel utilisateur

Miele

Miele KM 408-1 Manuel utilisateur

George Foreman

George Foreman GGR50B Manuel utilisateur

AOG

AOG T series Manuel utilisateur

Gorenje

Gorenje TG2000CB Mode d’emploi

Weber

Weber Genesis Silver-B Permamount NG 051701 Manuel utilisateur

Glen

Glen SA 3037 Manuel utilisateur