Garmin GPSMAP 2006 Manuel utilisateur

7.5" (190 mm)

5.91"

(150 mm)

GPSMAP 2006/2006C/2106/2206/3006C/3206

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE.

UNIT OUTLINE

GPSMAP 2x06/2x10/3x06/3x10

FLUSH MOUNT TEMPLATES

Drill a 3/8" (6 mm) hole.

Begin cutting here.

Be very careful when cutting this hole,

because there is only a small amount

of clearance between the unit and the

mounting hole.

To flush mount the GPSMAP 2006/2006C/2106/2206/3006C/3206:

1. Trim the flush mount template and tape it in the preferred location.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting

holes before cutting the hole for the unit allows for an easier installation.)

4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.

5. Using the jig saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, because there is only a

small amount of clearance between the case molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a .05" Allen wrench to tighten the mounting studs

until the stop contacts the case. Be careful not to overtighten, because this may damage the

mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit into the cut out of the mounting surface.

8. Place washers over the mounting studs, then thread on one hex nut per mounting stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second hex nut on all four mounting studs to lock the first one

in place.

Garmin International 1200 E. 151st Street, Olathe, KS 66062 190-00243-00 Rev. F April 2006 Printed in Taiwan

9.05" (230 mm)

8.19"

(208 mm)

GPSMAP 2010/2010C/2110/2210/3010C/3210

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE.

UNIT OUTLINE

Drill a 3/8" (6 mm) hole.

Begin cutting here.

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

Be very careful when cutting this hole,

because there is only a small amount of

clearance between the unit and the

mounting hole. To flush mount the GPSMAP 2010/2010C/2110/2210/3010C/3210:

1. Trim the flush mount template and tape in the preferred location.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting

holes before cutting the hole for the unit allows for an easier installation.)

4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.

5. Using the jig saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, because there is only a

small amount of clearance between the case molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a .05" Allen wrench to tighten the mounting studs

until the stop contacts the case. Be careful not to overtighten, because this may damage the

mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit into the cut out of the mounting surface.

8. Place washers over the mounting studs, and then thread on one hex nut per mounting stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second hex nut on all four mounting studs to lock the first one

in place.

Autres manuels pour GPSMAP 2006

4

Ce manuel convient aux modèles suivants

6

Autres manuels Garmin GPS

Garmin

Garmin GTN 6 series Manuel utilisateur

Garmin

Garmin GPSMAP 400 series Manuel utilisateur

Garmin

Garmin StreetPilot I2 - Automotive GPS Receiver Guide de configuration

Garmin

Garmin ZUMO 346 LMT-S Western Europe Manuel utilisateur

Garmin

Garmin Approach S3 Manuel utilisateur

Garmin

Garmin nuvi 2405 series Manuel d'instructions

Garmin

Garmin GPSMAP 420 Manuel utilisateur

Garmin

Garmin eTrex Vista HCx Guide de référence

Garmin

Garmin GNC 420W Manuel utilisateur

Garmin

Garmin iQUE 3600 Manuel utilisateur

Garmin

Garmin DRIVE 52 Manuel utilisateur

Garmin

Garmin GTN 725 Manuel

Garmin

Garmin iQUE 3600 Manuel utilisateur

Garmin

Garmin nuvi 57 Manuel utilisateur

Garmin

Garmin Mobile 10 Guide de configuration

Garmin

Garmin Approach G5 - GPS-Enabled Golf Handheld Manuel utilisateur

Garmin

Garmin GPSMAP 60Cx Manuel utilisateur

Garmin

Garmin Forerunner 201 - Running GPS Receiver Manuel utilisateur

Garmin

Garmin Diamond DA40 Manuel

Garmin

Garmin Colorado 300 - Hiking GPS Receiver Guide de référence

Garmin

Garmin GPSMAP 76 series Manuel utilisateur

Garmin

Garmin Zumo 200 Series Manuel utilisateur

Garmin

Garmin Fishfinder 80 Manuel utilisateur

Garmin

Garmin GNC 420 Manuel utilisateur

Manuels GPS populaires d'autres marques

Raven

Raven Cruizer II Manuel

Hama

Hama 53118 Manuel utilisateur

Jigabot

Jigabot EX Manuel utilisateur

Pointer

Pointer Cellocator CelloTrack XT LTE Guide d'installation

Queclink

Queclink GV55LITE Manuel utilisateur

Voxson

Voxson Voxtrack GPS500 Manuel d'instructions

Starcom Systems

Starcom Systems Kylos Compact Manuel utilisateur

Cobra

Cobra Marine MC 600Ci Manuel utilisateur

Cellocator

Cellocator CelloTrack T Manuel utilisateur

Enfora

Enfora Mini-MT GSM2228UG001 Manuel utilisateur

Magellan

Magellan eXplorist 100 Manuel utilisateur

LTE

LTE G50B Manuel utilisateur

SkyGolf

SkyGolf SkyCaddie SG1 Manuel utilisateur

Kenwood

Kenwood DNN9330BT Manuel utilisateur

Safelet

Safelet Indra Manuel utilisateur

Bushnell

Bushnell 360100 Manuel utilisateur

Geneq

Geneq SXBlue Manuel utilisateur

ORIGO

ORIGO ED308 Manuel utilisateur