Garmin AMPS Rugged Mount Manuel utilisateur

Instructions

AMPSRuggedMount

MONTANA™600Series

AMPSRuggedMountInstructions





See the Important Safety and Product Information in the Montana product box

before installing the rugged mount.

notice

Incorrectly wiring the power/audio cable with bare wire leads can result in damage

to the vehicle or the battery. Garmin strongly recommends having an experienced

installer with the proper knowledge of electrical systems install the mount.



• AMPS Rugged Mount

• Anti-glare screen protector with applicator card and instructions

• 4 nuts and 4 washers (for AMPS mount)

• 4 screws (for AMPS mount)

• Security screw tool

NOTE: Installation of the rugged mount to all vehicles requires an AMPS mount

(not included).



Garmin’s standard limited warranty applies to this accessory. For more

information, see the Important Safety and Product Information in the Montana

product box.

AMPSRuggedMountInstructions



notice

If any wire is left unconnected, insulate the wire and safely secure it on your

vehicle.

1. Select a location to mount the Montana on your vehicle, based on available

power sources, safe cable routing, and that the driver view is not obstructed.

2. Connect the red

➊

and black

➋

wires to your vehicle’s main power (10 to 50

Volts).

➏

➋

➊

➌

➍

➎

3. If necessary, connect the serial data wires to your vehicle.

• Yellow

➌

is the serial data input wire.

• Blue

➍

is the serial data output wire.

• Green

➎

is the serial ground wire.

4. If necessary, connect the audio jack

➏

AMPSRuggedMountInstructions



The AMPS mount is not included with the rugged mount.

1. Thread the screws

➊

through the washers

➋

, mount

➌

, and AMPS mount base

plate

➍

(not included).

➊

➋➌

➍

➎

2. Tighten the nuts

➎

to secure the base plate.

The recommended torque is 15–20 lbf-in (1.7 to 2.25 Nm).



notice

Before placing the device in the mount, ensure that the metal contacts on the

device and the mount are dry to avoid equipment damage. Use the weather cap to

keep the mount cradle dry.

1. Place the weather cap

➊

in the storage area on the mount.

➋

➊

➌

2. Fit the bottom of your device into the cradle

➋

3. Tilt the device back until it snaps into place.

4. Using the security screw tool, tighten the security screw

➌

on the top of the

mount.

NOTE: If reected light or glare makes the device display difcult to see, apply

an anti-glare screen protector to the screen.



1. Loosen the security screw.

2. Press the button on the side of the mount to release

the device.

3. Lift out the device.

4. Place the weather cap

➊

on the cradle.

➊

Shop for other gadgets & electronics on our website.

Table des matières

Autres manuels Garmin Accessoires

Garmin

Garmin GRF 10 Manuel utilisateur

Garmin

Garmin IMPACT Manuel utilisateur

Garmin

Garmin GSC 10 Manuel utilisateur

Garmin

Garmin GSC 10 Manuel utilisateur

Garmin

Garmin GFS 10 - Fuel Sensor Guide de référence

Garmin

Garmin GWS 10 Marine Wind Sensor Manuel utilisateur

Garmin

Garmin LIDAR-LITE V4 LED Manuel d'instructions

Garmin

Garmin GMA 240 Manuel utilisateur

Garmin

Garmin GPSMAP 5012 - Marine GPS Receiver Guide de configuration

Garmin

Garmin STEADYCAST HEADING SENSOR Manuel utilisateur

Garmin

Garmin Intelliducer Transom Mount Sensor with Depth & Temperature (NMEA... Manuel utilisateur

Garmin

Garmin GTM 20 - TMC Module Guide de référence

Garmin

Garmin GPSMAP 4208 - Marine GPS Receiver Manuel d'utilisation

Garmin

Garmin GDL 90 UAT Guide de démarrage rapide

Garmin

Garmin GWS 10 Marine Wind Sensor Manuel utilisateur

Garmin

Garmin GPS 17x Manuel utilisateur

Garmin

Garmin GTM 10 - TMC Module Guide de référence

Garmin

Garmin GHC 10 Manuel utilisateur

Garmin

Garmin nuvi 350 Manuel utilisateur

Garmin

Garmin SPEED SENSOR 2 Manuel d'instructions

Garmin

Garmin GRF 10 Manuel utilisateur

Garmin

Garmin A03451 Manuel d'instructions

Garmin

Garmin Speed Sensor Manuel utilisateur

Garmin

Garmin GLO Glonass Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur