Garett Smile Manuel utilisateur
User manual
MULTILANGUAGE
www.garett.eu
SmartWatch
Locator GPS
Garett Smile
MULTILANGUAGE
English 3
Polski 20
Română 107
Magyar 72
Nederlands 90
Slovenčina 124
Lietuvos 55
Українська 141
INFO (EN/PL) 158
Český 38
English
lClean the device only with a soft, slightly damp cloth. Do not use chemicals
or detergents to clean this device.
lIt is forbidden to throw equipment into the fire. There is a risk of battery
explosion and, as a consequence, life and health hazards.
lDo not dive in the device.
lThe device should be protected against heat sources and direct sunlight.
lUsing this device near medical devices may interfere with their operation.
Pay special attention when using the smartwatch near medical devices,
such as pacemakers, hearing aids and other electronic medical devices.
lDo not immerse the device in water.
Before use, carefully read the user's manual and save it for later use. The
manufacturer is not responsible for any damage / injury caused by
improper use. Depending on the particular SmartWatch, some functions
may differ with the functions described in the user manual..
lIt is forbidden to use the device if it is damaged.
lIn the event of damage, have the device serviced by an authorized service
center for inspection / repair. Attempting to repair it yourself may lead to
damage to the device and will void the warranty.
SECURITY ISSUES
3. Camera
5. Nano SIM card slot
4. Charging Port
6. Microphone
7. Speaker
1. Display
2. Turn on / o ff/ wake up /
screen / return / reject
connection
PRODUCT
DESCRIPTION
REQUIREMENTS FOR NANO SIM CARD
1. Install the card in the Nano SIM standard.
2. The SIM card must meet the following conditions:
lThe card must be active (if the new card, should be activated in a mobile
phone by making an outgoing call)
lThe card must be top up on the account (for pre pay cards)
lThe card must support work mode 2G, it must have a service, internet
and number identification functions.
lThe card can not have an active PIN (to check the card has an active
PIN lock installed on the mobile phone and check if it will be asked for
the PIN code during the launch. If yes, the lock is active and you will
need to put it in the phone settings or by contacting operator)
Due to the fact that the device uses the Internet connection, in order
not to generate additional costs, we recommend to buy an internet
package from the operator. Package 1GB per month is enough. The
cost of internet connection, and the amount of voice and SMS
messages are regulated by the pricing of the mobile network operator.
ATTENTION: SIM cards offered by the operator as online, dedicated to
e.g. tablets, may not work in the device.
INSTALLATION OF NANO SIM CARD
STANDARD
SIM MICRO
SIM NANO
SIM
V
1. Firstly, using the included
Screwdriver, unscrew the screws
that secures the plug, the SIM card
port (5) located on the back of the
watch.
2. After unscrewing the screw and
removing the plug, install the Nano
SIM card so that its chip contacts in
the slot of the device and cut corner
matches the cut corner in the slot.
It is recommended to install the
SIM card when the device is
turned off.
CHARGING
2. Mount the watch in the holder so that the two contact pins (4) join the
contact of the handle. Then set up the other end of the cable with a USB
port of the computer or a USB adapter, e.g. from a mobile telephone. When
we properly connect the cable, the screen will appear the loading
animation. When the battery is completely discharged, the animation
may appear only after several minutes.
1. SmartWatch charge using a dedicated magnetic holder attached to the
device.
Before the first switch on the watch, it is recommended to charge it
for 2 hours.
SMARTWATCH ON HAND
Be sure to put the watch on cild wrist and adjust the strap so that it will be
not too loose.
FIRST USE
1. When the SIM card is correctly installed in the watch and meets all the
above conditions, we can start the device by pressing and holding the
button for + 3 seconds (2).
4. When Internet connection is active, we can go to the next stage which is
the installation of the Global Tracker application on our smartphone. The
main menu of the watch will be described in the following part of the
manual, because the full functionality of the smartwatch is obtained after
registering and configuration through Global Tracker applications.
2. After starting the watch you will see a main screen displaying the most
important information, such as hour, date, GSM coverage and battery level.
Inactive icons will be in grey color.
3. After starting the watch, we wait a few seconds and the icon of the range
and the connection to the Internet will become active (white) as in the
picture above. Connecting to the Internet is necessary for further
configuration of the device. If after a minute the range and Internet
connection will not be active (grey color), make sure that the SIM card
meets all previously described requirements and the watch is in a place
with a strong range. You might also turn o ffand restart the watch.
APPLICATION INSTALLATION
GLOBAL TRACKER
Full functionality of the localizer and configuration is obtained after installing
the Global Tracker application on our smartphone with Android or iOS.
The application is compatible with Android 4.4, iOS 7 (and higher). Find
applications by typing in the search engine the name " Global Tracker "or by
scanning the corresponding QR code shown below.
Android iOS
REGISTRATION IN THE APPLICATION
1. Launch Global Tracker application.
3. To register a new account, click on the "Register" option.
2. After starting the application, you will see a login screen where you can log
in to your account if you have already created it or register it: a new account or
change the application's language.
7. Next, click "Register". After the
correct registration, the following
message will be displayed:
"Successful Registration "and return
to the login screen.
4. In the first field, enter any active
email address, which will be the login
to the application.
5. In the next field Enter the code:
123456
6. In the next field, we provide a
password, which together with the
email address will be as the login data
in the application. Password can
have from 6 to 16 characters. We can
use numbers and letters.
8. Next, click "LOGIN" to log in to the
newly created account. In the next
step, we will be asked for a phone
number. Enter the number of the
person who installs the applications
and will manage the settings of the
watch. After entering the number,
click "Confirm".
9. In the next window we will pair the
watch with the created account. To do
this, click "Bind Watch". It will display
a screen that will allow you to scan
the individual QR code of the watch.
The code can be entered manually.
10. After the scan or enter the QR
code we can go to the next stage.
In this step, we choose the
relationship between the
administrator and the user of the
watch: e.g. Dad - the
administrator is the user's daddy,
Mom - the administrator is the
mum for the user, etc. Under
such a name the administrator
will be in the phone book of the
watch. We do not need to use the
default relationship names. By
entering the name in the field
"Device name" we can give: any
name for the administrator. After
code we can go to the next stage.
11. It will display some information
about the user of the watch:
selecting the name for the
administrator, click "Next Step.
lMobile phone: phone number the
card on the watch.
lName: name the user of the watch.
lBirthday
lHeight
lWeight
After adding the data, click ,, confirm
". When the assignment of the watch
succeeds, the following message will
appear: "Binding success" and on the
screen will appear: ,, Registration
Succes ".
ATTENTION: When using any
application function, or if you want
to configure the settings, the
following message will be
displayed: "Device is not on the
network" means that the smart
watch has no active internet
connection. Check whether the
SIM card meets all the
requirements described earlier in
the manual. If the card meets the
requirements, the most common
reason for this message is not the
lGender
proper APN configuration. The
APN configuration is
described in the following
section of the manual in the
PROBLEM SOLVING section.
Table des matières
Langues :
Autres manuels Garett Montre
Garett
Garett SARA Manuel utilisateur
Garett
Garett GT20S Manuel utilisateur
Garett
Garett FIT 14 Manuel utilisateur
Garett
Garett Kids Cloud 4G Manuel utilisateur
Garett
Garett Kids 5 Manuel utilisateur
Garett
Garett G11 Manuel utilisateur
Garett
Garett Action Manuel utilisateur
Garett
Garett Women LISA Manuel utilisateur
Garett
Garett Garett Women DIANA Manuel utilisateur
Garett
Garett Lady Elegance RT Manuel utilisateur
