Furuno MU-201CE Manuel utilisateur

MONITOR UNIT MU-201CE/MU-231CE

OPERATOR'S MANUAL

This manual describes only the key operations of the monitor unit MU-210CE/MU-231CE.

For other details, refer to the installation manual and operator’s manual of the ECDIS/radar.



1. Overview

When the monitor unit MU-201CE or MU-231CE is connected to a radar/ECDIS

with an RS-232C cable, the keys on the panel are locked, so independent

operation of the keys is not possible. Brilliance is controlled from ECDIS/radar.

Key function under lock condition

 Simultaneous pressing of Lock and Menu keys: Opens/closes the menu.

 Simultaneous pressing of Lock and Input keys: Choose an input signal.

 Simultaneous pressing of Lock and keys: Turns the power on or off. To

turn it off, press more than five seconds.

The keys are unlocked with menu operation. See “Keypad lock” on page 6. The

key functions under unlocked condition are as follows.

 key: Turns the power on or off. To turn the power off, press it more than

fiveseconds.

 + and -: Adjusts the screen brilliance when no menu displayed. With menu

displayed, these choose an item from the menu.

 Input: Chooses input signal to display (when no menu is displayed).

 Menu: Opens or closes menu.

 Enter: Confirms menu setting.

Lock Menu Enter Input - +

LED

Operation Panel

LED lamp: lights when the monitor unit is turned on.

2. Menu Operation

1. Press the Menu key to open the main menu.

The chosen menu item is circumscribed with a blue rectangle and its sub-menu is

displayed below the main menu.

2. Press the + or – key to choose a menu and press the Enter key.

3. Press the + or – key to choose a sub-menu item and press the Enter key.

There are four kinds of items available in each sub-menu.A brief explanation

of each follows.

Keys

They just need to be confirmed for

selection in order to activate the

corresponding function. The key in this

example will perform factory defaults

restore as soon as selected.

On/off settings

They just need to be confirmed for

selection in order to toggle between the on

and off state of the option. The setting in

this example will toggle between normal

mode and freeze frame mode as selected.

Item lists

Once activated, these items allow the user

to select a given mode of operation among

the ones available by pressing the + or –

key and then Enter key.

Gauges

Once activated, these items allow the user

to change the setting at will between zero

and one hundred percent by pressing the +

or - key and then Enter key.

4. To change other item in the sub-menu, return to step 3.

5. Press the Menu key to conclude sub-menu setting.

To change the setting of another menu, go to step 2.

6. Press the Menu key to close the main menu.

Scroll

3. Menu Functions

This section of the manual describes each function of each menu in detail. Each

paragraph represents a given menu. On the left, an image shows all items that

can appear in that menu, while on the right an item by item description is given,

in the same order as shown at the screen. Each paragraph is named after the

menu it represents, and the icon for that menu is shown near the menu name.

Please note that the numeric values shown in the boxes are meaningless and do

not represent values that are meant to be valid. When using the equipment, the

GUI will allow or disallow some values to be entered depending on the current

conditions.

Also note that no item is shown as selected.Although every possible item is

shown in the images, not all of them may be shown on the equipment's GUI

when using it, because each item is shown only if certain conditions are met.

Information menu

Input resolution

This box shows details of the signal that is currently

displayed. The values shown are: horizontal

resolution (pixels), vertical resolution (pixels) and

vertical refresh frequency (Hz). The content of this

box cannot be changed.

Detected mode

The value displayed in this box cannot be changed

and informs the user about the numeric identifier

associated with the signal displayed. This is useful

to establish if two given input signals have identical

parameters or not.

Firmware version

This box cannot be selected, and its value cannot

be changed. It informs the user about the version of

the firmware programmed into the monitor.

Main window image settings

Backlight

Adjust the intensity of the backlight of the display.

This is automatically adjusted by radar/ECDIS.

LED level

Adjust the intensity of the LED on the front panel.

Brightness

Make the picture brighter or darker.

Contrast

View dark details on dark backgrounds. This setting

should be adjusted after the brightness so as to

make the white color as bright as possible without

interfering with grays.

Sharpness

Make the picture more or less detailed. More

detailed pictures are clearer but introduce some

picture noise, while less detailed pictures are

slightly blurred but have reduced noise.

Gamma correction

Choose the chromatic response of the display. In

particular, "linear" should be used with flat panel

LCD displays.

Color temp

Make the picture warmer or colder by changing the

white temperature. The value is expressed in

Kelvin.

Red, green and blue temp

Change the quantity of red, green and blue that the

image contains.

Scaling mode

Choose how to view signals with an aspect ratio

different from that of the display. The "one to one"

mode displays the signal without scaling. The "fill

all" mode stretches the picture so the whole screen

gets filled; this may make the picture squashed or

stretched. The "fill to aspect ratio" mode makes the

input signal fill the screen but without squashing or

stretching, maintaining the aspect ratio of the input

signal. Use the default setting.

After installation or execution of Factory defaults (page 6), set the brightness,

contrast, and red/green/blue temperatures as follows.

MU-201CE

Brightness 43%

Contrast 60%

Redtemp 50%

Green temp 67%

Bluetemp 65%

MU-231CE

Brightness 43%

Contrast 55%

Redtemp 50%

Green temp 67%

Bluetemp 65%

General monitor settings

Freeze frame

This function, when activated, freezes the image

on the screen, disregarding the input signal until

deactivated.

Source information

This setting allows the user to disable the source

information that appears on the upper left hand

corner each time a source is detected or Input

key is pressed.Always use On state.

OSD timeout

Choose how much time the GUI will remain

displayed on the screen when no control is being

used. When the user is not touching the monitor

controls, this timer will, after the selected period of

time, remove the GUI from the screen.

Logo timeout

Choose how much time the logo will remain on

the screen when the display is powered. The

"Disabled" option will make the display skip the

logo display at start up.

Monitor timeout

Choose how much time the monitor will remain

powered when the user is not touching its

controls. The "Disabled" setting disables this

feature. After the selected time has passed and

the user has not touched the monitor controls, it

will automatically power off. Set to "Disabled" for

radar/ECDIS.

Monitor address

Choose to which address the monitor should

respond when ECDIS commands are detected

over the serial link.

Serial mode

Choose what kind of serial bus is connected to

the monitor. Use the default setting (RS 232).

Monitor to monitor

Choose whether the display initiates an ECDIS

transmission towards the other displays

connected to it when the user tries to adjust the

backlight level. In "Slave" mode, the monitor

never initiates ECDIS transmissions on its own. In

"Master" mode, the monitor issues an ECDIS

command over the serial link each time the

backlight is changed. This function is only

available if serial mode is set to 422 or 485.

Keypad lock

Set whether the keypad is locked or not. When

locked, the keypad does not answer to user

commands, unless the LOCK key is pressed

together with a desired key. If the monitor is

connected to radar/ECDIS with an RS-232C

cable, Off returns to On after turning the power off

and then on.

Serial protocol

Choose how the equipment will respond to

ECDIS commands. In Standard ECDIS mode, the

equipment will be compliant with the ECDIS

specification, while in ISIC ECDIS mode the

values are transmitted in decimal representation

and are scaled to a percentage range.

OSD Position

Choose if the On Screen Display is shown on the

right or left side of the monitor.

User preferences

Factory defaults

This function provides a reset of the monitor

to the factory defaults. By activating this

function, all settings made by the user will be

lost and the monitor will be brought back to

known operating conditions.

Setup selection

This setting allows the user to select which

user slot to handle with the Save monitor

setup and Recall monitor setup keys.

Save monitor setup

This function allows the user to save all

important current settings to a memory for

later recall. There are three slots available;

which one is used to store the settings

depends on the Setup selection menu item.

Saving settings in a slot that contains

previous settings will overwrite the old

settings to store the new ones.

Recall monitor setup

This function allows the user to recall the

settings stored with the Save monitor setup

push key. Which setting is recalled depends

on the Setup selection menu item.

Inputselection

Source

Choose the input source for the main

screen. As soon as a change is made

here, the corresponding input will be

selected and activated for display on the

main screen. To change the active source

for the PIP window, use the PIP menu.

Source enable items

These menu items allow the user to

disable some sources. When a source is

disabled (set to Off), it cannot be selected

by means of the Input key on the

monitor's keypad.

Main screen acquisition settings

This menu is available when PIP is set to ON.

(See next page.)

Mode selection

Choose a memory slot in which to store

display parameters for a given input signal.

Once stored in a memory slot, the settings for

the current input signal can be modified at will,

and they will be reapplied when the same

source is detected again.

Mode details

This box shows what's inside the memory slot

selected with the Mode selection setting.

Load current mode

This stores the settings detected by the image

processor for the current signal in the memory

slot selected with the Mode selection setting.

Once the detected parameters have been

stored in memory, they can be edited by the

user with the controls described below.

Clear

Press this key to delete the contents of the

selected memory slot. Once the content of a

given slot has been deleted, it is lost and

cannot be retrieved.

H. total

Adjust the frequency of the clock signal used

to drive the analog to digital converter that

samples the input signal.

Phase

Adjust the phase of the clock used to drive the

analog to digital converter that samples the

input signal.

H. res. and V. res.

By means of this setting, the user is able to

force the image processor into detecting the

current signal with a given horizontal or

vertical resolution.

H. pos. and V. pos

These two settings allow the user to move the

input signal around on the main screen, so it is

displayed correctly in its entirety.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Furuno Moniteur

Furuno

Furuno FEA-2107 Manuel utilisateur

Furuno

Furuno MU-170C Manuel utilisateur

Furuno

Furuno MU-155C Manuel

Furuno

Furuno FMD-3200 Manuel utilisateur

Furuno

Furuno NAVnet 1722 Manuel utilisateur

Furuno

Furuno MU-201C Manuel utilisateur

Furuno

Furuno Mu-190HD Manuel utilisateur

Furuno

Furuno RD-30 Manuel utilisateur

Furuno

Furuno MFD8 Manuel utilisateur

Furuno

Furuno SFD-1010 Manuel

Furuno

Furuno TZT12F Manuel utilisateur

Furuno

Furuno FMD3100 Manuel utilisateur

Furuno

Furuno NAVNET 3D MFDBB Manuel utilisateur

Furuno

Furuno SFD-1010 Manuel utilisateur

Furuno

Furuno NavNet TZtouch3 Series Manuel utilisateur

Furuno

Furuno MU-201C Manuel utilisateur

Furuno

Furuno MFD12 Manuel utilisateur

Furuno

Furuno TZTL12F Manuel

Furuno

Furuno MU-150C Manuel utilisateur

Furuno

Furuno MU-150HD Manuel utilisateur

Furuno

Furuno TZT9F Manuel utilisateur

Furuno

Furuno NAVNET TZ2 TZTL12F Manuel utilisateur

Furuno

Furuno NAVNET 3D MFDBB Manuel utilisateur

Furuno

Furuno FMD3100 Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation

LG M1950D-PZ Manuel utilisateur