Fujitsu MBA3300 NP SERIES Manuel utilisateur

C141-E270-01EN

MBA3300NC, MBA3300NP

MBA3147NC, MBA3147NP

MBA3073NC, MBA3073NP

HARD DISK DRIVES

PRODUCT MANUAL

FOR SAFE OPERATION

Handling of This manual

This manual contains important information for using this product. Read thoroughly before using the

product. Use this product only after thoroughly reading and understanding especially the section

“Important Alert Items” in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage

to their property. Use the product according to this manual.

IMPORTANT NOTE TO USERS

READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.

INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE

TO USERS, BYSTANDERS OR PROPERTY.

While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU assumes no

liability to any party for any damage caused by any error or omission contained in this manual, its updates

or supplements, whether such errors or omissions result from negligence, accident, or any other cause. In

addition, FUJITSU assumes no liability with respect to the application or use of any porduct or system in

accordance with the descriptions or instructions contained herein; including any liability for incidental or

consequential damages arising therefrom.

FUJTSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION CONTAINED

HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.

FUJITSU reserves the right to make changes to any products described herein without further notice and

without obligation.

This product is designed and manufactured for use in standard applications such as office work, personal

devices and household appliances. This product is not intended for special uses (atomic controls,

aeronautic or space systems, mass transport vehicle operating controls, medical devices for life support, or

weapons firing controls) where particularly high reliability requirements exist, where the pertinent levels of

safety are not guaranteed, or where a failure or operational error could threaten a life or cause a physical

injury (hereafter referred to as "mission-critical" use). Customers considering the use of these products for

mission-critical applications must have safety-assurance measures in place beforehand. Moreover, they are

requested to consult our sales representative before embarking on such specialized use.

The contents of this manual may be revised without prior notice.

The contents of this manual shall not be disclosed in any way or reproduced in any media without the

express written permission of Fujitsu Limited.

C141-E270

REVISION RECORD

Edition Date published Revised contents

01 October, 2007

Specification No.: C141-E270-**EN

C141-E270

Related Standards

Product specifications and functions described in this manual comply with the following ANSI

(*1) standards.

Document number Title

T10/1236D Rev.20 [NCITS.351:2001] SCSI Primary Commands-2 (SPC-2)

T10/996D Rev.8c [NCITS.306:1998] SCSI-3 Block Commands (SBC)

T10/1157D Rev.24 SCSI Architecture Model-2 (SAM-2)

T10/1365D Rev.10 SCSI Parallel Interface-4 (SPI-4)

*1 ANSI = American National Standard Institute

In case of conflict between this manual and any referenced document, this manual takes

precedence.

Compliance with Administration on the Control of Pollution Caused by Electronic

Information Products of the People's Republic of China

This product is shipped as a component to manufacture the final products. Therefore, the

packaging material code provided in GB18455-2001 is not marked on any packaging part of this

product.

C141-E270

PREFACE

This manual describes the MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP, MBA3073NC, and

MBA3073NP 3.5-inch SCSI hard disk drives.

This manual details the specifications and functions of the above disk drives, and gives the requirements

and procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of SCSI disk drives and their use in

computer systems. The MANUAL ORGANIZATION section describes organization and scope of this

manual. The need arises, use the other manuals.

OVERVIEW OF MANUAL

This manual consists of the following seven chapters and two appendixes:

CHAPTER 1 GENERAL DESCRIPTION

This chapter introduces the standard features, hardware, and system configuration of the HDD.

CHAPTER 2 SPECIFICATIONS

This chapter gives detailed specifications of the HDD and the installation environment.

CHAPTER 3 DATA FORMAT

This chapter describes the data structure, the addressing method, and the defect management.

CHAPTER 4 INSTALLATION REQUIREMENTS

This chapter describes the basic physical and electrical requirements for installing the disk drives.

CHAPTER 5 INSTALLATION

This chapter explains how to install the disk drives. It includes the notice and procedures for setting device

number and operation modes, mounting the disk drive, connecting the cables, and confirming drive

operation.

CHAPTER 6 DIAGNOSTICS AND MAINTENANCE

This chapter describes the automatic diagnosis and maintenance of the disk drive. This chapter also

describes diagnostic methods for operation check and the basics of troubleshooting the disk drives.

CHAPTER 7 ERROR ANALYSIS

This chapter describes in details how collect the information for error analysis and how analyze collected

error information.

APPENDIX A TO B

The appendixes give supplementary information, including a list of setting items and the signal

assignments of interface connector.

C141-E270 1

CONVENTIONS USED IN THIS MANUAL

The MBA3300NC, MBA3300NP, MBA3147NC, MBA3147NP, MBA3073NC, and MBA3073NP disk

drives are described as "the hard disk drive (HDD)," "the disk drive" or "the device" in this manual.

Decimal number is represented normally.

Hexadecimal number is represented as X'17B9', 17B9h or 17B9H.

Binary number is represented as "010".

CONVENTIONS FOR ALERT MESSAGES

This manual uses the following conventions to show the alert messages. An alert message consists of an

alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a

signal word.

The following are the alert signals and their meanings:

CAUTION

This indicates that either minor or moderate

personal injury may occur if the user does not

perform the procedure correctly.

IMPORTANT

This indicates information that the helps the user

use the product more effectively.

In the text, the alert signal is centered, followed below by the indented message. A wider line space

precedes and follows the alert message to show where the alert message begins and ends. The following is

an example:

(Example)

CAUTION

Damage

Never remove any labels from the HDD or deface them in any way.

The main alert messages in the text are also listed in the "Important Alert Items."

ATTENTION

Please forward any comments you may have regarding this manual.

To make this manual easier for users to understand, opinions from readers are needed. Please write your

opinions or requests on the Comment at the back of this manual and forward it to the address described in

the sheet.

2 C141-E270

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. This alert signal also indicates

that damages to the product or other property may occur if the user does not

perform the procedure correctly.

Task Alert message Page

Installation Damage

Never remove any labels from the HDD or deface them in any way.

High temperature

To prevent injury, never touch the HDD while it is hot. The DE and LSI

become hot during operation and remain hot immediately after turning off the

power.

Data loss

1. The user must not change the setting of terminals not described in this

section. Do not change setting status set at factory shipment.

2. Do not change the setting of terminals except following setting pins

during the power is turned on.

• Write protect: Pin pair 9/10 of the CN2 setting terminal

(NP model only)

3. To short the setting terminal, use the short plug attached when the device

is shipped from the factory.

Damage

1. Make sure that system power is off before connecting or disconnecting

cables.

2. Do not connect or disconnect cables when power is on.(except NC model)

Damage

1. Be careful of the insertion orientation of the SCSI connectors. With the

system in which terminating resistor power is supplied via the SCSI cable,

if the power is turned on, the overcurrent protection fuse of the

terminating resistor power supplier may be blown or the cable may be

burnt if overcurrent protection is not provided.

When the recommended parts listed in Table 4.2 are used, inserting the

cables in the wrong direction can be prevented.

2. To connect SCSI devices, be careful of the connection position of the

cable. Check that the SCSI device with the terminating resistor is the last

device connected to the cable.

C141-E270 3

Task Alert message Page

Installation High temperature

To prevent injury, never touch the HDD while it is hot. The DE and LSI

become hot during operation and remain hot immediately after turning off the

power.

Data loss

When the SEND DIAGNOSTIC command terminates with the CHECK

CONDITION status, the initiator must collect the error information using the

REQUEST SENSE command. The RECEIVE DIAGNOSTIC RESULTS

command cannot read out the error information detected in the self-

diagnostics.

Data loss

Save data stored on the HDD to other media before requesting repair. Fujitsu

does not assume responsibility if data is corrupted during servicing or repair.

High temperature

To prevent injury, never touch the HDD while it is hot. The DE and LSI

become hot during operation and remain hot immediately after turning off the

power.

Diagnostics and

Maintenance

Electrical shock

- To avoid shocks, turn off the power before connecting or disconnecting a

cable, connector, or plug.

- Never touch the HDDs while power-feeding.

100

Damage

- Always ground yourself with a wrist strap connected to ground before

handling. ESD (Electrostatics Discharge) may cause the damage to the

device.

- To prevent electrical damage to the HDD, turn the power off before

connecting or disconnecting a cable, connector, or plug.

- Never remove a PCBA.

- Never use a conductive cleaner to clean the HDDs.

- Ribbon cables are marked with a colored line. Connect the ribbon cable

to a cable connector with the colored wire connected to pin 1.

- Never open the HDD for any reason.

100

Damage

- Never remove any labels from the HDD or deface them in any way.

- Never open the DE for any reason. Doing so will void any warranties.

107

4 C141-E270

MANUAL ORGANIZATION

PRODUCT

MANUAL

(This manual)

1. General Description

2. Specifications

3. Data Format

4. Installation Requirements

5. Installation

6. Diagnostics and Maintenance

7. Error Analysis

SCSI PHYSICAL

INTERFACE

SPECIFICATIONS

1. SCSI Bus

2. SCSI Message

3. Error Recovery

SCSI LOGICAL

INTERFACE

SPECIFICATIONS

1. Command Processing

2. Data Buffer Management

3. Command Specifications

4. Parameter Data Formats

5. Sense Data and Error Recovery Method

6. Disk Media Management

C141-E270 5

This page is intentionally left blank.

Autres manuels pour MBA3300 NP SERIES

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Stockage

Fujitsu

Fujitsu ETERNUS CS800 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX Disk Manuel utilisateur

Fujitsu

Fujitsu MPE3XXXAE Manuel utilisateur

Fujitsu

Fujitsu RE25U Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX60 Manuel de référence

Fujitsu

Fujitsu ETERNUS DX60 S2 Manuel utilisateur

Fujitsu

Fujitsu MHV2100AH Manuel utilisateur

Fujitsu

Fujitsu MHZ2040BH - Mobile 40 GB Hard Drive Manuel utilisateur

Fujitsu

Fujitsu MAH3182MC SERIES Manuel utilisateur

Fujitsu

Fujitsu DynaMO 640FE Manuel utilisateur

Fujitsu

Fujitsu PG-HD9G1C Manuel utilisateur

Fujitsu

Fujitsu ETERNUS2000 100 Manuel utilisateur

Fujitsu

Fujitsu MHT2080BH Manuel utilisateur

Fujitsu

Fujitsu Streamer DAT 160 Manuel utilisateur

Fujitsu

Fujitsu GP5-HDH461 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS CS800 Manuel utilisateur

Fujitsu

Fujitsu GP5-HDH8B Manuel utilisateur

Fujitsu

Fujitsu MHW2040BS Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX S4 Series Manuel utilisateur

Fujitsu

Fujitsu GRANPOWER5000 Manuel utilisateur

Fujitsu

Fujitsu MAB3045 Manuel utilisateur

Fujitsu

Fujitsu MPD3XXXAT Manuel utilisateur

Fujitsu

Fujitsu MHE2043AT Manuel utilisateur

Fujitsu

Fujitsu MHV2040AH - Mobile - Hard Drive Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur