Fujitsu l ETERNUS AF Manuel utilisateur
FUJITSU Storage
ETERNUS DX, ETERNUS AF
Configuration Guide -Server Connection-
(Fibre Channel) for Oracle Solaris
Driver Settings for Fujitsu Fibre Channel Cards
P3AM-3712-15ENZ0
This page is intentionally left blank.
Preface
This manual briefly explains the operations that need to be performed by the user in order to connect an
ETERNUS DX/AF to a server running Solaris OS and using Fujitsu Fibre Channel cards via a Fibre Channel inter-
face.
This manual is used when performing the setup procedure described in "Installing Drivers and Setting Up the
Server" and "Recognizing the Logical Units" of the "Configuration Guide -Server Connection- (Fibre Channel)
for Oracle Solaris".
This manual should be used in conjunction with any other applicable user manuals, such as those for the
ETERNUS DX/AF, server, OS, Fibre Channel cards, and drivers.
Refer to "Configuration Guide -Server Connection- Notations" for the notations used in this manual such as
product trademarks and product names. For storage systems that are supported by the OS, refer to the Server
Support Matrix of the ETERNUS DX/AF.
15th Edition
April 2017
The Contents and Structure of this Manual
This manual is composed of the following six chapters and an appendix.
•"Chapter 1 Workflow" (page 5)
This chapter describes the workflow required to establish a connection between a server with Fujitsu Fibre
Channel cards and an ETERNUS DX/AF.
•"Chapter 2 Installing the Fibre Channel Card Driver" (page 7)
This chapter describes how to install the Fibre Channel card driver.
•"Chapter 3 Installing the hddv Driver" (page 8)
This chapter describes how to install the hddv driver that is required when connecting the ETERNUS DX/AF
storage systems and a Fujitsu driver equipped server in a single-path configuration.
•"Chapter 4 Setting Up the Server" (page 9)
This chapter describes how to set up the server for different connection topologies.
•"Chapter 5 Setting Up the Server to Recognize the Logical Units" (page 18)
This chapter describes how to make the server recognize the LUNs of the ETERNUS DX/AF.
•"Chapter 6 Required Driver Parameters" (page 22)
This chapter describes how to set up the Fujitsu Fibre Channel card driver.
An appendix contains the various management tables that are used in "Chapter 4 Setting Up the Server".
3
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Table of Contents
Chapter 1 Workflow 5
Chapter 2 Installing the Fibre Channel Card Driver 7
Chapter 3 Installing the hddv Driver 8
Chapter 4 Setting Up the Server 9
4.1 Creating a WWN Instance Management Table for the Server.......................................................... 9
4.2 Creating a WWN Instance Management Table for Storage System ............................................... 12
4.3 Creating a Target Binding Table ................................................................................................... 13
4.4 Setting the Configuration File (fjpfca.conf) .................................................................................. 14
4.5 Re-checking the Settings.............................................................................................................. 14
Chapter 5 Setting Up the Server to Recognize the Logical Units 18
5.1 Recognizing Logical Units with the sd Driver................................................................................ 18
5.1.1 Logical Unit Recognition.....................................................................................................................................18
5.1.2 Getting the Server to Recognize the Logical Units...............................................................................................19
5.2 Recognizing Logical Units with the hddv Driver............................................................................ 21
Chapter 6 Required Driver Parameters 22
6.1 Setting Up the Parameters ........................................................................................................... 22
6.1.1 "fjpfca.conf" Parameter Values............................................................................................................................22
6.1.2 "/kernel/drv/fjpfca.conf" Example........................................................................................................................24
Appendix A Various Management Table Templates 25
A.1 WWN Instance Management Table for the Server ........................................................................ 25
A.2 WWN Instance Management Table for Storage System ................................................................ 25
A.3 Target Binding Table.................................................................................................................... 26
4
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Chapter 1
Workflow
This chapter describes the driver settings required to establish a connection between a server with Fujitsu
Fibre Channel cards and an ETERNUS DX/AF.
Workflow
Installing the Fibre Channel Card Driver
Install the driver. Download the proper driver from the Fujitsu web-site as required.
•"Chapter 2 Installing the Fibre Channel Card Driver" (page 7)
•Used for driver installation
-Documentation provided with the product
Creating Various Management Tables
Enter the necessary information in the "WWN Instance Management Table for the Server", "WWN In-
stance Management Table for Storage System", and "Target Binding Table".
•"Chapter 4 Setting Up the Server" (page 9)
•"Appendix A Various Management Table Templates" (page 25)
Editing the Configuration File
Set the driver parameters by editing the configuration file.
•"Chapter 4 Setting Up the Server" (page 9)
•"Chapter 6 Required Driver Parameters" (page 22)
•Check the settings using the "grmpdautoconf" command
-ETERNUS Multipath Driver product manual
5
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Setting Up the Server to Recognize the Logical Units (LUNs)
Make the server recognize the ETERNUS DX/AF logical units using the sd driver.
•"Chapter 5 Setting Up the Server to Recognize the Logical Units" (page 18)
After completing all the required procedures in this manual, proceed to "Setting the Multipaths" in
"Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris".
Chapter 1 Workflow
6
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Chapter 2
Installing the Fibre Channel Card Driver
Install the Fibre Channel card driver according to the installation guide provided with the Fibre Channel card.
7
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Chapter 3
Installing the hddv Driver
Use the hddv driver if it is already installed and used. Do not use the hddv driver for new connections.
8
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Chapter 4
Setting Up the Server
The server setup will vary according to how the ETERNUS DX/AF storage systems and server are to be connec-
ted. Edit the server's configuration file to match the chosen topology. Configuration files may also differ de-
pending on which Fibre Channel cards are to be used.
There are two possible connection topologies: direct connection and switch connection. Procedures are de-
scribed below. Also refer to the FUJITSU PCI Fibre Channel manuals as necessary.
●For direct connection
Instance name data of the Fibre Channel card is necessary. Refer to the following sections to set.
•"4.1 Creating a WWN Instance Management Table for the Server" (page 9)
•"4.2 Creating a WWN Instance Management Table for Storage System" (page 12)
•"4.4 Setting the Configuration File (fjpfca.conf)" (page 14)
•"4.5 Re-checking the Settings" (page 14)
●For switch connection
The Fibre Channel card Instance name, target WWN, and target ID information are necessary. Check each
item and enter them in the table. Edit the configuration file according to those information and make set-
tings.
Refer to the following sections to set.
•"4.1 Creating a WWN Instance Management Table for the Server" (page 9)
•"4.2 Creating a WWN Instance Management Table for Storage System" (page 12)
•"4.3 Creating a Target Binding Table" (page 13)
•"4.4 Setting the Configuration File (fjpfca.conf)" (page 14)
•"4.5 Re-checking the Settings" (page 14)
4.1 Creating a WWN Instance Management Table for the Server
Create a "WWN instance management table for the server" with information regarding the Fibre Channel
card.
Determine the following information for each Fibre Channel card installed in the server and enter it into a
copy of the "WWN instance management table for the server" (provided in "Appendix A Various Management
Table Templates" (page 25)).
•Physical slot name
•WWN
•Instance name
•Physical path name
9
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Table 4.1 WWN Instance Management Table for the Server
Physical slot name WWN Instance name Physical path name
1Check the instance names.
"fjpfca + instance number" is the format used to represent Fibre Channel card instance names.
The instance number that corresponds to the physical path in which the Fibre Channel card is installed
is stored in the "/etc/path_to_inst" file at the Fibre Channel card driver installation. Extract the necessary
lines using the "grep" command.
# grep "fjpfca" /etc/path_to_inst
Example:
"/pci@6,4000/fibre-channel@2" 1 "fjpfca"
"/pci@4,2000/fibre-channel@1" 0 "fjpfca"
(1) (2)
(1) indicates the physical path name and (2) indicates the instance number.
"fjpfca1" is the instance name of the "/pci@6,4000/fibre-channel@2" path Fibre Channel card.
"fjpfca0" is the instance name of the "/pci@4,2000/fibre-channel@1" path Fibre Channel card.
2Enter the results in "Instance name" and "Physical path name" columns of the "WWN instance manage-
ment table for the server".
Physical slot name WWN Instance name Physical path name
/pci@4,2000/fibre-channel@1
/pci@6,4000/fibre-channel@2
fjpfca0
fjpfca1
3Check the WWN of each Fibre Channel card.
Execute the following command to check the WWN that corresponds to the Fibre Channel card instance
name.
# /usr/sbin/FJSVpfca/fc_info -a
"adapter=fjpfca#x" ("x" is instance number) is the format used to represent Fibre Channel card instant
names. The WWN corresponding to the instance name is displayed after "wwn=".
Chapter 4 Setting Up the Server
4.1 Creating a WWN Instance Management Table for the Server
10
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-3712-15ENZ0
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Fujitsu Serveur
Fujitsu
Fujitsu PRIMERGY RX600 S3 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY BX620 S6 Manuel du propriétaire
Fujitsu
Fujitsu PRIMERGY RX600 S6 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY TX600 S2 Manuel utilisateur
Fujitsu
Fujitsu PRIMEQUEST 2000 Series Manuel de service
Fujitsu
Fujitsu PRIMERGY MX130 S1 Manuel utilisateur
Fujitsu
Fujitsu SPARC ENTERPRISE T5220 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY TX1330 M4 Manuel utilisateur
Fujitsu
Fujitsu BX630 - PRIMERGY - S2 Dual Manuel du propriétaire
Fujitsu
Fujitsu Primergy TX300 S4 Mode d’emploi
Fujitsu
Fujitsu PRIMERGY BX900 Manuel utilisateur
Fujitsu
Fujitsu 1FINITY L100 Manuel utilisateur
Fujitsu
Fujitsu BS2000 SE Series Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY Econel 50 Manuel du propriétaire
Fujitsu
Fujitsu PRIMEQUEST 480 Mode d’emploi
Fujitsu
Fujitsu PRIMEQUEST 2000 Series Manuel utilisateur
Fujitsu
Fujitsu PRIMEQUEST 2000 Series Manuel de service
Fujitsu
Fujitsu primergy h250 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY TX120 S2 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY RX4770 M4 Manuel utilisateur
