FSP Technology K948 Manuel utilisateur
Version 1.0 August 2013
Bedside Terminal
Hardware System
User Manual
i
Copyrig t 2013
All Rig ts Reserved
Manual Version 1.0
T e information contained in t is document is subject to c ange wit out notice.
We make no warranty of any kind wit regard to t is material, including, but not
limited to, t e implied warranties of merc antability and fitness for a particular
purpose. We s all not be liable for errors contained erein or for incidental or
consequential damages in connection wit t e furnis ing, performance, or use of
t is material.
T is document contains proprietary information t at is protected by copyrig t. All
rig ts are reserved. No part of t is document may be p otocopied, reproduced or
translated to anot er language wit out t e prior written consent of t e
manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Ot er trademarks mentioned erein are t e property of t eir respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect t e mac ine from t e electrical Power Supply, turn off t e power
switc and remove t e power cord plug from t e wall socket. T e wall socket
must be easily accessible and in close proximity to t e mac ine.
2. Read t ese instructions carefully. Save t ese instructions for future reference.
3. Follow all warnings and instructions marked on t e product.
4. Do not use t is product near water.
5. Do not place t is product on an unstable cart, stand, or table. T e product may
fall, causing serious damage to t e product.
6. Slots and openings in t e cabinet and t e back or bottom are provided for
ventilation; to ensure reliable operation of t e product and to protect it from
over eating. T ese openings must not be blocked or covered. T e openings
s ould never be blocked by placing t e product on a bed, sofa, rug, or ot er
similar surface. T is product s ould never be placed near or over a radiator or
eat register, or in a built-in installation unless proper ventilation is provided.
7. T is product s ould be operated from t e type of power indicated on t e
marking label. If you are not sure of t e type of power available, consult your
dealer or local power company.
8. Do not allow anyt ing to rest on t e power cord. Do not locate t is product
w ere persons will walk on t e cord.
9. Never pus objects of any kind into t is product t roug cabinet slots as t ey
may touc dangerous voltage points or s ort out parts t at could result in a fire
or electric s ock. Never spill liquid of any kind on t e product.
ii
CE MARK
T is device complies wit t e requirements of t e EEC directive 2004/108/EC
wit regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage
Directive”
FCC
T is device complies wit part 15 of t e FCC rules. Operation is subject to t e
following two conditions:
(1) T is device may not cause armful interference.
(2) T is device must accept any interference received, including interference
t at may cause undesired operation
"Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment."
T is equipment as been tested and found to comply wit t e limits for a Class
B digital device, pursuant to part 15 of t e FCC Rules. T ese limits are designed
to provide reasonable protection against armful interference in a residential
installation.
T is equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance wit t e instructions, may cause armful
interference to radio communications. However, t ere is no guarantee t at
interference will not occur in a particular installation. If t is equipment does
cause armful interference to radio or television reception, w ic can be
determined
by turning t e equipment off and on, t e user is encouraged to try to correct t e
interference by one or more of t e following measures:
—Reorient or relocate t e receiving antenna.
—Increase t e separation between t e equipment and receiver.
—Connect t e equipment into an outlet on a circuit different from t at to w ic t e
receiver
is connected.
—Consult t e dealer or an experienced radio/TV tec nician for elp
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type.
Dispose of used battery according to t e local disposal instructions.
Indicating t at replacement by inadequately trained personnel could result in a
azard (suc as excessive temperatures, fire, or explosion)
Lit ium battery: CR2032
iii
Safety Caution
Note: To comply wit IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
legislation, perip erals s all be 4.7.3.2 "Materials for fire enclosure" compliant.
4.7.3.2 Materials for fire enclosures
For MOVABLE EQUIPMENT aving a total mass not exceeding
18kg.t e material of a FIRE ENCLOSURE, in t e t innest significant
wall t ickness used, s all be of V-1 CLASS MATERIAL or s all pass
t e test of Clause A.2.
For MOVABLE EQUIPMENT aving a total mass exceeding 18kg
and for all STATIONARY EQUIPMENT, t e material of a FIRE
ENCLOSURE, in t e t innest significant wall t ickness used, s all
be of 5VB CLASS MATERIAL or s all pass t e test of Clause A.1
CAUTION SYMBOL IN CARTON
ATTENTION
WARNING:
To avoid risk of electric s ock, t is equipment must only be connected to a supply
mains wit protective eart .
WARNING:
Do not modify t is equipment wit out aut orization of t e manufacturer.
WARNING:
If an appliance coupler or separable plug is used as t e disconnecting device, it s all
iv
be readily identifiable and easily reac ed by t e operator. For single-p ase portable
equipment, a plug on a cord of lengt not greater t an 3m is considered to be easily
reac ed.
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on t e treatment,
collection, recycling and disposal of electric and electronic devices and t eir
components.
T e crossed dustbin symbol on t e device means t at it s ould not be disposed of
wit ot er ouse old wastes at t e end of its working life. Instead, t e device
s ould be taken to t e waste collection centers for activation of t e treatment,
collection, recycling and disposal procedure.
To prevent possible arm to t e environment or uman ealt from uncontrolled
waste disposal, please separate t is from ot er types of wastes and recycle it
responsibly to promote t e sustainable reuse of material resources.
House old users s ould contact eit er t e retailer w ere t ey purc ased t is
product, or t eir local government office, for details of w ere and ow t ey can
take t is item for environmentally safe recycling.
Business users s ould contact t eir supplier and c eck t e terms and conditions
of t e purc ase contract.
T is product s ould not be mixed wit ot er commercial wastes for disposal.
Power supply is specified as a part of ME EQUIPMENT
Please read t e user manual
v
Revision History
Revision Date Description
V1.0 August, 2013 Release
vi
Table of Contents
1 Intended Use ...................................................... 1
2 Package C ecklist ............................................ 2
2-1 Standard Items ................................................................................. 2
3 System View ....................................................... 3
3-1 Front View .......................................................................................... 3
3-2 Side View............................................................................................ 4
3-3 Rear View ........................................................................................... 4
3-4 Bottom View ...................................................................................... 5
3-5 Dimension .......................................................................................... 5
4 System Assembly .............................................. 6
4-1 SSD/HDD Replacement .................................................................. 6
5 Perip erals Installation .................................... 7
5-1 P one module Installation .............................................................. 7
5-2 Stand Installation ………………………………………………………………….8
6 Specification ...................................................... 9
7 Jumper Setting ................................................ 12
7-1 C73 Mot erboard ........................................................................... 12
7-2 Connectors & Functions ................................................................ 13
7-3 Jumper Setting ................................................................................ 14
1
1 Intended Use
According to t e Instructions for Use (IFU) of t e manufacturer, t e Bedside Terminal
as t e following intended use:
T e Bedside Terminal Hardware System is a computing device capable of storing,
retrieving and sending data electronically. T is Bedside Terminal Hardware System,
including its user interface, battery, PCB and power supply, is intended to be fixed to a
stand in medical care environment.
2
2 Package C ecklist
2-1 Standard Items
a. System
b.
P one module
c. Power adapter d. Power Cable
e. Manual f. Stand
3
3 System View
3-1 Front View
Number
Description
1Build-in camera
2Camera LED
3Touc screen
4
Touc keys (from left to rig t: reading lig t, volume down,
volume up, c annel down, c annel up , power button)
5Smart IC card reader
6VOIP p one (optional)
Table des matières
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
