Frico SL-DC1 Manuel utilisateur

Installations and user manual

SL/SLS-DC1

SL/SLS-R1

Original instructions

.... 2

GB .... 52

NO .... 83

.... 27

Conformity

This unit complies with European directives:

• Low tension directive 2006/95/CE

• Electro-magnetic compatibility 2004/108/CE.

The pictograms in the next chapter provide the necessary

information for correct, safe use of the machine in a rapid,

unmistakable way

Symbols

Safety pictograms

Generic danger

- Signals to the personnel that the operation described could

cause physical injury if not performed according to the safety

rules.

Danger of high voltage

- Signals to the personnel that the operation described could

cause electrocution if not performed according to the safety

rules.

Danger due to heat

- Signals to the personnel that the operation described could

cause burns if not performed according to the safety rules.

Do Not

- Refers to actions that absolutely must not be performed.

A quick guide is found at the end of the manual.

General

General warnings 4

Fundamental safety rules 4

Product range 5

Nominal technical features 5

Overall dimensions 6

Installation of SL/SLS - DC1/R1

Positioning the unit 7

Installation modes 7

Minimum installation distances 7

Side opening 8

Vertical oor or wall installation 8

Horizontal or ceiling installation (SL) 9

Mounting front grill safety support (SL) 9

Dimensions 10

Condensation discharge 10

Filling the system 11

Evacuating air while lling the system 11

Electrical connections 12

Mounting the valve kits 12

Installation of internal control (ECA644) model DC1

Mounting, setting and connection of on-board machine control panels ECA644 13

Mounting 13

Setting auxiliary functions dip-switches B and C 14

CP presence contact input connection 14

Mounting air temperature probe 15

Wiring diagram 16

Installation of control for remote operation (B10642) model R1

Mounting and connecting the fan control for remote adjustment B10642 17

Mounting 17

LED signals 17

Diagram for B10642 connections with 0-10 V DC thermostats/signals 18

B10642 connection with 0-10 V thermostats 18

Troubleshooting

Troubleshooting 19

Table of anomalies and remedies 19

User instructions

SMART TOUCH electronic panel with continuous on- board modulation 20

Display 20

Key function 20

General start-up 21

Activation 21

Heating / cooling operating mode set-up 21

Stand By 21

Temperature selection 21

Automatic operation 22

Silent operation 22

Night function 22

Operation at maximum ventilation speed 22

Key locking 22

Minimum brightness reduction 22

Deactivation 23

Room temperature probe offset adjustment 23

Long term shut-down 23

Error signals 23

Maintenance 24

Cleaning the outside 24

Cleaning air suction lter 24

Energy saving tips 26

After unpacking, make sure that all the components are present.

If not, contact the Frico agent who sold the appliance to you.

Frico appliances must be installed by an authorised installer

who, on completion of the work, will release a declaration of

conformity to the client in respect of the laws in force and the

indications given by Frico in the instructions leaflet supplied

together with the appliance.

These appliances have been designed both for conditioning

and/or heating environments and must be destined for this use

only and compatibly with their performance characteristics.

Frico accepts no responsibility, either contractual or extra-

contractual, for any damage caused to persons, animals of

property as a result of incorrect installation, adjustment or

maintenance or improper use.

In case of water leaks, turn the master switch of the system to

"OFF" and close the water taps.

As soon as possible, call professionally qualified personnel and

do not intervene personally on the appliance.

If the appliance is not used for a log period of time, the following

operations should be performed:

- Turn the master switch of the system to "OFF"

- Close the water taps

- If there is the risk of freezing, make sure that anti-freeze has

been added to the system otherwise empty the system.

If the room temperature is too low ot too high it is damaging for

the health and is also a useless waste of energy.

Do not leave the room closed for long periods. Periodically

open the windows to ensure a correct change of air.

This instruction leaflet is an integral part of the appliance

and consequently must be kept carefully and must ALWAYS

accompany the appliance, even when it is passed to a new

owner or user or transferred onto another system.

All repair or maintenance interventions must be performed

by the technical service department or by professionally

qualified personnel as foreseen in this booklet. Do not modify

or intervene on the appliance as this could create dangerous

situations and the manufacturer will not be responsible for any

damage caused.

Danger from burns - take care when touching

Remember that some fundamental safety rules should be

followed when using a product that uses electricity and water,

such as:

It is forbidden to carry out any cleaning before having

disconnected the appliance from the electricity mains supply

by turning the system master switch to "OFF".

It is forbidden to modify the safety or adjustment devices

or adjust without authorisation and indications of the

manufacturer.

It is forbidden to pull, cut or knot the electrical cables coming

out of the appliance, even if it is disconnected from the mains

supply.

It is forbidden to poke objects or anything else through the

inlet or outlet grills.

It is forbidden to open the doors which access the internal

parts of the appliance without first turning the system master

switch to "OFF".

It is forbidden to dispose of or leave in the reach of children

the packaging materials which could become a source of

danger.

It is forbidden to climb onto the appliance or rest any object on

it.

The external parts of the appliance can reach temperatures of

more than 70°C.

General

General warnings

Fundamental safety rules

The water batteries is offered in 2 sizes with different performances

and dimensions.

1. SL

Fan convector SL-DC is suitable for wall mounting.

Fan convector SL-R1 is suitable for wall and ceiling mounting.

2. SLS

Fan convector SLS-DC is suitable for wall mounting.

Fan convector SLS-R1 is suitable for wall and ceiling mounting for

heating operation. Only wall mounting for cooling operation.

2 pipes

TECHNICAL DATA

SL/SLS 200 400 600 800 1000

Battery water contents SLS l 0,24 0,4 0,57 0,73 0,9

Battery water contents SL l 0,47 0,8 1,13 1,46 1,8

Maximum working pressure bar 10 10 10 10 10

Maximum water inlet temperature °C 80 80 80 80 80

Minimum inlet water temperature °C 4 4 4 4 4

Hydraulic fixtures "

Eurokonus 3/4 Eurokonus 3/4 Eurokonus 3/4 Eurokonus 3/4 Eurokonus 3/4

Power supply V/ph/Hz 230/1/50 230/1/50 230/1/50 230/1/50 230/1/50

Maximum current absorbed A 0,11 0,16 0,18 0,26 0,28

Maximum power absorbed W 11,9 17.6 19,8 26,5 29,7

Weight SL kg 17 20 23 26 29

Weight SLS kg 12 14 16 19 23

Product range

Nominal technical features

Art.

Type

76628 SL200DC1

76629 SL400DC1

76630 SL600DC1

76631 SL800DC1

76632 SL1000DC1

Art.

Type

76633 SLS200DC1

76634 SLS400DC1

76635 SLS600DC1

76636 SLS800DC1

76639 SLS1000DC1

Art.

Type

76614 SL200R1

76616 SL400R1

76617 SL600R1

76618 SL800R1

76619 SL1000R1

Art.

Type

76623 SLS200R1

76624 SLS400R1

76625 SLS600R1

76626 SLS800R1

76627 SLS1000R1

U.M.

SL/SLS 200 SL/SLS 400 SL/SLS 600 SL/SLS 800 SL/SLS 1000

A mm 735 935 1135 1335 1535

659

579

A129

129

459

379

SLS

2 pipes

Dimensions

Overall dimensions

max 2500 mm

80 mm

140 mm

80 mm

400 mm

20 mm20 mm

Wall mounting Ceiling mounting

All models SLS-R1: Heating

SL-R1: Heating/cooling

Flammable material

Installation of SL/SLS - DC

Avoid installing the unit in proximity to:

- positions subject to exposure to direct sunlight;

- in proximity to sources of heat;

- in damp areas or places with probable contact with water;

- in places with oil fumes

- places subject to high frequencies.

Make sure that:

- the wall on which the unit is to be installed is strong enough to

support the weight;

- the part of the wall interested does not have pipes or electric

wires passing through;

- the interested wall is perfectly flat;

- there is an area free of obstacles which could interfere with the

inlet and outlet air flow

- in case of ceiling installation (SL) the airflow is not directed

towards persons.

The following descriptions of the various mounting phase and the

relative designs refer to a version of the machine with fixtures on

the left.

The operations for the mounting of machines with fixtures on the

right are exactly the same.

Only the images are to be considered as a mirror image.

To ensure that the installation is performed correctly and that the

appliance will perform perfectly carefully follow the instructions

indicated in this manual. Failure to respect the rules indicated

not only can cause malfunctions of the appliance but will also

invalidate the warranty and hence Frico shall not respond for any

damage to persons, animals or property.

Figure indicates the minimum mounting distances between the

wall-mounted cooler-convector and furniture present in the room.

Positioning the unit

Installation modes

Minimum installation distances

A AB

- On the left-hand side lift the cover that protects the screw,

loosen the screw that fixes the left panel, then move it slightly

to the left and lift it up.

- On the opposite side, lift the cover that protects the screw and

unscrew it.

- Move the side panel slightly to the right and lift it out.

When mounting on the floor with support feet, refer to the

individual instructions leaflets supplied and the relative manual for

the mounting of the feet.

Using the paper template, trace the position of the two fixing

brackets on the wall. Use a suitable drill to make the holes with and

insert the toggle bolts (2 for each bracket); fix the two brackets. Do

not over-tighten the screws so that the brackets can be adjusted

with a spirit level.

Fully tighten the four screws to block the two brackets.

Check the stability by manually moving the brackets to the right

and to the left, up and down.

Mount the unit, checking that it fits correctly onto the brackets and

checking that it is stable.

cover

fixing screws

left panel

right panel

Side opening

Vertical oor or wall installation

Atoggle bolts Bbrackets



A A B

Using the paper template, trace on the ceiling the position of the

two fixing brackets and the two rear screws. Using a suitable drill,

make the holes and insert the toggle bolts (2 for each bracket);

fix the two brackets. Do not over-tighten the screws. Position the

machine on the two brackets, keeping it in position and then fix the

two screws into the rear toggle bolts, one on each side.

Make sure that there is sufficient inclination of the unit towards the

drainage pipe to facilitate the water drainage.

Fully tighten all 6 fixing screws.

The installation of SLS units (with cooling effect) in horizontal

position is prohibited. .

Carefully check the inclination of the exhaust pipe. Any

counterslope of the discharge line can cause water leakage

In the case in which the cooler-convector is installed in a horizontal

position, to guarantee the safety of the cleaning/filter replacement

operations it is obligatory that the two clamps, in the supplied bag

together with the instruction manual and the accessories, are

mounted by the installer.

Install braces to prevent the fall of the grid.

- Separate the two clamps;

- open the front grill and completely unscrew the fixing screws

on the springs;

- fix the two clamps, blocking them by retightening the screws;

- fix the other part of the clamp to the grill using the supplied

screw;

- close the grill.

Horizontal or ceiling installation (SL)

Mounting front grill safety support (SL)

Atoggle bolts

Bbrackets

Cscrews

Ddrainage pipe

ATies

BScrews fixing springs

Cgrid

U.M. 200 400 600 800 1000

mm 12 14 16 18 20

ø14mm

The choice and sizing of the hydraulic lines must be made by an

expert who must operate according to the rules of good technique

and the laws in force, taking into account that undersized pipes

cause a malfunction.

To make the connections:

- position the hydraulic lines

- tighten the connections using the “spanner and counter

spanner” method

- check for any leaks of liquid

- coat the connections with insulating material.

The hydraulic lines and joints must be thermally insulated.

Avoid partially insulating the pipes.

Do not over-tighten to avoid damaging the insulation.

Use hemp and green paste to seal the threaded connections; the

use of Teflon is advised when there is anti-freeze in the hydraulic

circuit.

Minium inner pipeline diameter

The condensation discharge network must be suitably sized

(minimum inside pipe diameter 16 mm) and the pipeline positioned

so that it keeps a constant inclination, never less than 1%. In the

vertical installation, the discharge pipe is connected directly to

the discharge tray, positioned at the bottom of the side shoulder

underneath the hydraulic fixtures. In a horizontal installation the

discharge tube is connected to the one already present on the

machine.

- If possible, make the condensation liquid flow directly in a

gutter or a “rainwater” discharge.

- When discharging directly into the main drains, it is advisable

to make a siphon to prevent bad smells returning up the pipe

towards the room. The curve of the siphon must be lower than

the condensation collection bowl.

- If the condensation needs to be discharged into a container,

it must be open to the atmosphere and the tube must not be

immerged in water to avoid problems of adhesiveness and

counter-pressure that would interfere with the normal outflow.

- If there is a height difference that could interfere with the

outflow of the condensation, a pump must be mounted:

- in a vertical installation mount the pump under the lateral

drainage tray;

- in a horizontal installation the pump position must be decided

according to the specific requirements.

Such pumps are commonly found in commerce.

However, on completion of the installation it is advisable to check

the correct outflow of the condensation liquid by slowly pouring

about ½ l of water into the collection tray in about 5-10 minutes.

Connect to the condensation collection tray discharge union a pipe

for the outflow of the liquid blocking it adequately. Check that the

drip-collector extension is present and correctly installed.

Mounting the condensation discharge pipe in the vertical version

Dimensions

Condensation discharge

Adischarge fitting

Btube for the outflow of the liquid

Cextension drip

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Frico Chauffage

Frico

Frico PFW Series Manuel utilisateur

Frico

Frico Pamir 2500 Manuel utilisateur

Frico

Frico Tiger P51 Manuel utilisateur

Frico

Frico Elztrip EZ106N Manuel utilisateur

Frico

Frico SWL Series Manuel utilisateur

Frico

Frico PF Smart Manuel utilisateur

Frico

Frico Thermozone AC 400 Manuel utilisateur

Frico

Frico Thermocassette CTS Manuel utilisateur

Frico

Frico PA3500 Series Manuel utilisateur

Frico

Frico SWT02 Manuel utilisateur

Frico

Frico SWS02 Manuel utilisateur

Frico

Frico Tiger Manuel utilisateur

Frico

Frico PA4200 Series Manuel utilisateur

Frico

Frico Thermozone ADA Series Manuel utilisateur

Frico

Frico IH Series Manuel utilisateur

Frico

Frico Elektra H Series Manuel utilisateur

Frico

Frico SIReFAEMX Manuel utilisateur

Frico

Frico Thermozone AGI Manuel utilisateur

Frico

Frico AREC4000 Series Manuel utilisateur

Frico

Frico Aquaztrip H Manuel utilisateur

Frico

Frico Infratower IHA30BP Manuel utilisateur

Frico

Frico PFSE4 Manuel utilisateur

Frico

Frico Tiger P21 Manuel utilisateur

Frico

Frico Infrasmart IHS20W/B/S24 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur