Frico SIReAC Manuel utilisateur

.... 19

.... 2

For more languages, please see www.frico.se

For wiring diagram, please see p.71-73

SIRe Competent Air Curtains

Water

With quick guide

SIReAC

Original instructions

.... 54

.... 36

SIRe Competent Air Curtains Water

Enter ID

The control system can control one or more

units in parallel (max 9). Each unit must have

a unique ID number (1-9) which is set in the

ID selector of the PC board.

E.g.) Unit 1: ID=1, unit 2: ID=3

If the external control for some reason has

not been installed the unit can still be run

temporarily. The ID selector is then set to

mode 0 in the image below. The function is

half speed and heating on.

When the ID number must be changed the

unit must be disconnected from power.

Quick guide / Start up

Check that all constituent parts are present

(see section Constituent parts).

Advice about location

PC board HUB SIReC1X is installed close

to the unit. Control unit SIReUA1 has an

integrated room temperature sensor and

is installed so that it is easily accessible

to the user. RJ12 modular cables, which

are available in different lengths, are used

to connect the PC board and the control

unit. Longer cables are available as options.

Maximum cable lengths see section Options.

To prevent unauthorised people from

accessing the Control unit it can instead

be placed in another area and an external

room sensor, SIReRTX (option), can be

installed in the entrance to sense the correct

temperature. Maximum cable lengths see

section Options.

Connect the system

Control board Base SIReB1(X) in/at the unit

and control unit SIReUA1 are connected

by PC board HUB SIReC1X with RJ12

modular cables. In SIReB1(X) the unit is also

connected further with RJ12 modular cable if

several units are to be connected in parallel.

If external room temperature sensor

SIReRTX (option) is used it is connected

using modular cable RJ11 on the PC Board

HUB SIReC1X.

The actuator for water control and door

switch SIReDC is connected to the terminal

block on PC board HUB SIReC1X.

When required for ﬁxed installation

the supplied cable and plug are removed.

Installation is carried out according to the

applicable regulations.

Wiring diagram

The wiring diagram is in a separate section at

the end of this manual.

When external PC board Base SIReB1X is

used, wiring between the PC board base and

the air curtain unit must be done. Please see

separate manual for SIReB1X

Set language

English

Start-up guide

Set temp. unit

°C

°F

Start-up guide

Set date

2011-05-28

YYYY-MM-DD

Start-up guide

Set time

14:07

24h format

Start-up guide

Function test

Start test

Skip test

Start-up guide

Screen function test

Fan step 1-5

Heating step off-1

Start-up guide

Function test

Test completed

Restart test

Start-up guide

Start-up finished

Proceed

Restart wizard

Start-up guide

Checking system

Startguide

Start up

System supplied with power. At the ﬁrst start

up, the start-up wizard is run and the basic

settings are made. Fan and heating steps

are tested through the test program. Then a

status window is displayed.

Each unit should have

a unique ID on its

SIReB1(X) card.

To run the unit

temporarily without

external control select

mode 0.

SIRe Competent Air Curtains Water

Contents

Quick guide / Start up

Advice about location 19

Connect the system 19

Wiring diagram 19

Enter ID 19

Start up 19

Constituent parts

SIReAC 21

Option 22

Water control - valve package 23

Operating modes

Door that is opened and closed 24

Doors that are always or often left open for longer periods 24-25

Function description of current stage 25-26

Control unit SIReUA1

Overview 27

Main menu

Current settings 28

Temp. settings 28

Fan control 28

Summer / Winter 28

System on/off 28

Installer menu 28

Installer menu

Installer status screen 29

Week program 29

Settings fan 30

Settings heating 30-31

Filter guard settings 31

External control (BMS) 31-32

General settings 32

Support menu 32

Alarm and error codes 33-34

Connecting external control - including BMS functions 35

Wiring diagram 36-38

SIRe Competent Air Curtains Water

ROOM

PE N L

SUPPLY 230V

ACTUATOR

230V

SIReUA1,

control unit

Competent and

Advanced

SIReCC,

modular cables

SIReB1,

integrated

PC board Base

SIReC1X,

PC Board HUB

Competent

Constituent parts

SIReAC

Integrated in the air curtain

Wall unit

cover

SIReIT,

internal

temperature

sensors

SIReDC, magnetic

door contact

Type Description HxWxD

[mm]

[m]

SIReUA1 Control unit Competent and Advanced 120x70x35

SIReC1X PC Board HUB Competent 202x139x50

SIReDC Magnetic door contact

SIReB1 Integrated PC board Base

SIReIT Internal temperature sensor 1

SIReCC603 Modular cable RJ12 3

SIReCC605 Modular cable RJ12 5

Dimensions constituent parts

SIRe Competent Air Curtains Water

Option

SIReUR, kit

for recessed

installation

SIReCJ4,

joint piece

SIReCC,

modular cables

SIReCJ6,

joint piece

SIReRTX, external

room temperature

sensor

*) See separate manual.

Max. cable lengths

•Modular cable RJ12 between SIReUA1 and SIReC1X: max 50 m

•Modular cable RJ12 between SIReC1X and SIReB1(X): max 10 m

•Modular cable RJ12 between two SIReB1(X): max 50 m

•Modular cable RJ11 to room sensor SIReRTX: max 20 m

Total RJ12 cable length permitted in the system is a maximum of 300 m.

Type RSK-no. E-no. Description HxWxD

[mm]

[m]

SIReRTX 673 09 22 87 510 12 External room temperature sensor 70x33x23

SIReUR* 673 09 21 87 510 11 Kit for recessed installation 114x70x50

SIReCJ4 Joint piece for two pcs. RJ11 (4/4)

SIReCJ6 Joint piece for two pcs. RJ12 (6/6)

SIReCC603 673 09 23 87 510 13 Modular cable RJ12 3

SIReCC605 673 09 24 87 510 14 Modular cable RJ12 5

SIReCC610 673 09 25 87 510 15 Modular cable RJ12 10

SIReCC615 673 09 26 87 510 16 Modular cable RJ12 15

SIReCC403 673 09 27 87 510 17 Modular cable RJ11 3

SIReCC405 673 09 28 87 510 18 Modular cable RJ11 5

SIReCC410 673 09 29 87 510 19 Modular cable RJ11 10

SIReCC415 673 09 30 87 510 20 Modular cable RJ11 15

SIRe Competent Air Curtains Water

VOS

SD230

TBVC

BPV10

SD230

TBVCMP

BPV10

Water control - option

VAT, adjustment tool for

valve package

Water control - valve package

Type RSK-no. Description Flow Connection

VOS15LF 673 09 35 On/off Low DN15

VOS15NF 673 09 36 On/off Normal DN15

VOS20 673 09 37 On/off Normal DN20

VOS25 673 09 38 On/off Normal DN25

VOSP15LF 673 09 43 Pressure independent Low DN15

VOSP15NF 673 09 44 Pressure independent Normal DN15

VOSP20 673 09 45 Pressure independent Normal DN20

VOSP25 673 09 46 Pressure independent Normal DN25

VAT 482 98 30 Adjustment tool for valve package

SIRe Competent Air Curtains Water

Operating modes

Door that is opened and closed

The control function notes whether the door

is open or closed as standard, this mode is

default set and is called Fixed ﬂexible (the

setting is under Installer menu > Settings fan

> Door mode).

Open door

Indicates ÖP on the installer status screen.

The fan speed runs at high speed which is set

under Main menu > Fan speed > Max fan

speed.

Normally it is requested that heat is engaged

when the door is opened. The setpoint value

(Room temp. day) is then increased with

the ﬁxed setpoint value difference that can

be changed under Installer menu> Settings

heating > Open door setp. diff., factory

setting 3.0 K. The set point is set under Main

Menu > Temperature settings > Room temp.

day. If week program is used the night time

set point value is set under Main menu >

Temp. settings > Room temperature night.

The room temperature is measured using the

integrated room temperature sensor or the

external room temperature sensor, SIReRTX

(option).

Closed door

Indicated ST on the installer status screen.

The fan speed runs at low speed which is

set under Main menu > Fan speed > Speed

closed door.

Heating is regulated to Room temp. Day

which is set under Main Menu > Temperature

settings > Room temp. day. If week program

is used the night time set point value is

regulated against the Room temperature is set

under Main menu > Temp. settings > Room

temperature night. The room temperature

is regulated using the integrated room

temperature sensor or the external room

temperature sensor, SIReRTX (option).

When the door is closed - over run

When heat has been connected and the door

has been closed, high speed mode remains to

cool the unit from any excess heat during the

ﬁxed time that is set under Installer menu >

Settings fan > Door over run > High speed

over run and at low speed during a ﬁxed

time under Installer menu > Settings fan>

Door over run > Low speed over run , on

the condition that it is sufﬁciently warm in

the premises, otherwise the fans run until the

desired temperature has been reached.

When the door is closed, the set point value

shifts from room temperature + ﬁxed set point

value difference for open door to Room temp.

day/night.

Over run is factory set so that the over

run times are controlled according to how

often the door is opened (Auto mode under

Installer menu > Settings fan > Over run

door > Over run mode).

Doors that are always or often left open for

longer periods

If a door is always, or often, left open it is

possible to use a function called CURRENT

STAGE instead. The fan and heating steps

increase/decrease 6 or 9 steps (depending on

the type of unit) and are only controlled by

the room temperature.

Current stage is activated in two ways:

Doors that are always open

For a door that is always open, door mode

Locked open can be selected under Settings

fan> Door mode.

Doors that are often open for longer

periods

For a door that is often open Auto can be

selected under Installer menu > Settings

fan > Door mode. In Auto mode, the control

automatically switches between Flexible and

open modes depending on how often the door

has been open (when the door has been open

for longer than 300 seconds the function

changes from Flexible to Open).

SIRe Competent Air Curtains Water

Function description of current stage

The task of the Current stage function is to

balance the room climate when a door is

always open by using the right combination of

fan and heating step.

In open mode, the room temperature is read

every 60 seconds (the ﬁrst 6 cycles, and then

every 5 minutes and at each reading any

Current stage adjustments are made, i.e. fan

control and supplied out adjusted.

Winter

If winter mode is selected under Main Menu >

Summer / Winter.

• If the room temperature is more than 3

degrees below the current settings, the

current stage increases by 2 steps.

• If the room temperature is between 1 and

3 degrees below the current settings, the

current stage increases by 1 step.

• If the room temperature is more than 2

degrees above the current setting, the

current stage decreases by 1 step.

Summer

If summer mode is selected under Main Menu

> Summer / Winter, heating is blocked.

• If the room temperature is more than 2

degrees below the current settings, the

current stage increases by 1 step.

• If the room temperature is between 1 and

2 degrees below the current settings, the

current stage decreases by 1 step.

• If the room temperature is more than 2

degrees greater than the Current settings,

current stage increases by 1 step.

• If the room temperature is between 1

and 2 degrees above current settings, the

current stage decreases by 1 step.

If fan control has been max. limited under

Main Menu > Fan control> High speed limit,

all current stages will be used but the fan will

be limited to the current setting.

SIRe Competent Air Curtains Water

Table - Current stage for units with 5 fan controls

Current

stage

Fan Heating

00 OFF

11 OFF

22 OFF

32 ON

43 ON

53 ON

Current

stage

Fan Heating

00 OFF

11 OFF

22 OFF

32 ON

43 ON

53 ON

64 ON

75 ON

85 ON

Table - Current stage for units with 3 fan controls

SIRe Competent Air Curtains Water

°C

Status window

DOOR

Status window

Forward arrow

Rotary dial

Back arrow

Mode

Green LED

Alarm

Red LED

Explanations

Status window

The display shows the prevailing room

temperature, fan and heating step, door status

and day/night mode or Off when the week

program is used.

Forward arrow

Conﬁrm selection and proceed.

Rotary dial

Scroll between alternatives.

Back arrow

Go back.

After three minutes the control unit goes back

to displaying the status window.

Status window

Press forward arrow to enter the main

menu.

Control unit SIReUA1

Overview

Fan step

Heating step

Week program:

Day

Week program:

Night

Week program:

Out of operation

OFF

Table des matières

Autres manuels Frico Chauffage

Frico

Frico Tiger P203 Manuel utilisateur

Frico

Frico SWX C Series Manuel utilisateur

Frico

Frico Infraduo IHD17 Manuel utilisateur

Frico

Frico Comfortline AZR Series Manuel utilisateur

Frico

Frico Thermoplus Manuel utilisateur

Frico

Frico AC Corinte ACCS10 Manuel utilisateur

Frico

Frico Tiger 2 9 kW Manuel utilisateur

Frico

Frico Elztrip EZ200 Manuel de service

Frico

Frico Thermozone AD Corinte W Manuel de service

Frico

Frico Infrasmart IHS15W67 Manuel utilisateur

Frico

Frico IRC13 Manuel utilisateur

Frico

Frico PL1006 Manuel utilisateur

Frico

Frico PFW Manuel utilisateur

Frico

Frico Thermozone AGV 4000 A Series Manuel utilisateur

Frico

Frico Thermoplus EC Series Manuel utilisateur

Frico

Frico CIR105 Manuel utilisateur

Frico

Frico Elztrip EZ100 Manuel utilisateur

Frico

Frico PA3500 Series Manuel utilisateur

Frico

Frico PF Series Manuel utilisateur

Frico

Frico PAEC3200C Series Manuel utilisateur

Frico

Frico Thermozone AGI Manuel utilisateur

Frico

Frico Thermozone AC 300 Manuel utilisateur

Frico

Frico Thermozone PA3500 Manuel utilisateur

Frico

Frico ICW Series Manuel de la liste des pièces

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur