Freecom CABLE II PCMCIA Manuel utilisateur

CABLE II

PCMCIA / CardBus

Rev. 112

www.freecom.com

FREECOM CABLE II PCMCIA / CABLE II CardBus

Cable II PCMCIA

Cable II CardBus

TABLE OF CONTENTS

GENERAL INFORMATION:

Hardware requirements ..................................................................... Page 5

Software requirements ...................................................................... Page 5

Precautionary measures and operating instructions ........................ Page 5

CHAPTER 1:

Startup operation - Hardware installation ....................................... Page 6

CHAPTER 2:

Software installation under Windows 95 ......................................... Page 7

Software installation under Windows 98/ME ................................... Page 9

Software installation under Windows 2000 ..................................... Page 12

Software installation under Windows NT 4.0 ................................... Page 16

Software installation under DOS, Windows 3.x ............................... Page 17

CHAPTER 3:

Troubleshooting - General problems .............................................. Page 19

Table of Contents

FREECOM CABLE II PCMCIA / CABLE II CardBus

GB GB

Dear User,

welcome to the installation of your FREECOM Cable II PCMCIA, FREECOM

Cable II CardBus. Before installing the drive, please read through the following

points regarding its compatibility with your system.

If not noted otherwise, the Cable II CardBus and Cable II PCMCIA are installed in

the same way.

FREECOM Technologies GmbH Berlin, Germany

www.freecom.com

Warning !

purposes and may be trademarks or registered trademarks of the respective companies.

This device was designed for home or office use.

Warning! This device is equipment complying with EN55022 class A. This equipment

can cause radio disturbances in a residential area. If this is the case, the user has to take

appropriate measures and assume all responsibility and costs for. It may not be used

near or with any life-sustaing systems.

FREECOM Technologies is not liable for any damages that may occur from the use of

in keeping with technological advances.

General Information

Reliable performance of the FREECOM Cable II cannot be guaranteed for

configurations that do not meet the following requirements:

Hardware requirements

 min. PC 486DX

 min. 16 MB RAM

 a PCMCIA Interface (type II)

 a CardBus Interface (type II)

Software requirements

DOS/Win 3.x Win 95 Win 98 Win 2000 Win ME Win NT 4.0

Cable II PCMCIA x* x x x x x

Cable II CardBus - - x x x -

* only read mode

General Information

Precautionary measures and operating instructions

 Operate the FREECOM Cable II only in the temperature range from 10 - 45°C.

 If the FREECOM Cable II is moved from a cool location to a warmer one, wait

until the Cable II and your system warms to the ambient temperature before

using it, otherwise moisture from condensation could lead to errors.

 Do not use the FREECOM Cable II in a dusty environment.

 Do not drop the FREECOM Cable II or expose it to other types of shocks.

 The FREECOM Cable II should not be used near strong electromagnetic

radiation sources (speakers, mobile phones, etc.).

FREECOM CABLE II PCMCIA / CABLE II CardBus

CHAPTER 1: Startup operation - Hardware installation

1. Turn off your computer and all the equipment connected to it.

2. Connect the included power supply cable to the rear panel of the FREECOM

device.

Do not yet plug the power supply into the power outlet.

3. Connect the drive plug of the Cable II to the FREECOM device.

4. Attach the other connection on the Cable II to your PC. Following this, plug the

power supply of the FREECOM device into a power outlet.

5. Turn on your computer again.

6. You can now begin installing the software (Chap. 2).

"Plug&Play" with the Cable II PCMCIA for Windows 95 / 98, ME and

Windows 2000

To use the FREECOM drive for Windows, primary installation must be carried out

only once, according to the following software installation.

The FREECOM Cable II PCMCIA is Plug&Play compatible. If you work with Windows,

you can attach the PCMCIA while the drive is in use. Your FREECOM drive then

appears under "My Computer". Likewise, you can remove the Cable II PCMCIA

while the drive is in use, by first cancelling it. The FREECOM drive then disappears

from "My Computer". To cancel the PCMCIA, click on "Start", "Settings", "Control

Panel", "PC Card (PCMCIA)". Highlight the FREECOM Cable II PCMCIA and click on

"Stop". The Cable II PCMCIA can be removed when the command "You may now

safely remove the card" appears.

Computer

connection

FREECOM Cable II

connection to drive

Software installation

CHAPTER 2:Software installation

2.1 Software installation under Windows 95

No special software is required to install your FREECOM Cable II PCMCIA. We

however recommend using the driver on diskette/CD that we have enclosed. This

has been specially developed by FREECOM and is faster than the Windows driver.

FREECOM HighSpeed Driver (recommended)

Note: If you are not prompted to install the driver, Windows will install

the default driver automatically. Proceed then as described in the section

on later installation of the FREECOM HighSpeed driver.

To install the FREECOM driver, insert the FREECOM installation diskette/CD in your

PC drive.

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. The window "Hardware Installation Wizard" opens. The FREECOM Cable II

PCMCIA is recognized as "Standard IDE/ESDI Hard Disk Controller". Confirm

with "Next" to continue the installation.

3. The Freecom driver is found in the next the window. Confirm by clicking

Finish.

4. The driver is installed from the disk/CD.

5. To finish installing the driver, Windows asks you to restart your computer. After

restart your FREECOM drive appears under My Computer with new a new

drive letter

Uninstalling the FREECOM HighSpeed Driver

To uninstall the FREECOM HighSpeed driver, select the file "DriverRemove.exe" on

the installation diskette/CD and follow the on-screen instructions.

Windows Default Driver

No special software is required to install your FREECOM Cable II PCMCIA.

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. The window "Hardware Installation Wizard" opens. The FREECOM Cable II

PCMCIA is recognized as "Standard IDE/ESDI Hard Disk Controller". Confirm

with "Next" to continue the installation.

3. The driver is found in the next window. To install the Windows default driver,

click "Finish".

4. To finish installing the driver, Windows asks you to restart your computer. After

restart your FREECOM drive appears under My Computer with new a new

drive letter.

FREECOM CABLE II PCMCIA / CABLE II CardBus

Later Installation of the FREECOM HighSpeed Driver

Note: If you are not prompted to install the driver, your system has

automatically installed the Windows default driver for your FREECOM

Cable II PCMCIA.

To install the FREECOM HighSpeed driver, proceed as follows:

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. Open the "Device Manager" by right-clicking on the "My Computer" icon. A

menu opens. Select "Properties" and click on the "Device Manager" tab.

3. Click on the "+" next to the entry "Hard disk controllers".

4. Double-click on "Standard IDE/ESDI Hard Disk Controller".

5. Open the "Driver" tab. Then click on "Update Driver".

6. The "Update Device Driver Wizard" opens. Click on "Next".

7. The Freecom driver is automatically found in the next window.

8. To start the driver update, click Finish. To finish installation, Windows asks

you to restart your computer. Confirm by clicking Yes

9. After restart your FREECOM drive appears under My Computer with new a

new drive letter. Installation is now complete

2.2 Software installation under Windows 98/ME

No special software is required to install your FREECOM Cable II PCMCIA. We

however recommend using the driver on diskette/CD that we have enclosed. This

has been specially developed by FREECOM and is faster than the Windows driver.

FREECOM HighSpeed Driver (recommended)

Note: If you are not prompted to install the driver, Windows will install

the default driver automatically. Proceed then as described in the section

on later installation of the FREECOM HighSpeed driver.

To install the FREECOM driver, insert the FREECOM installation diskette/CD in your

PC drive.

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. The window "Hardware Installation Wizard" opens. The FREECOM Cable II

PCMCIA is recognized as "Standard IDE/ESDI Hard Disk Controller". Confirm

with "Next" to continue the installation.

3. In the next window the option for finding the best driver for the device has

been selected. Confirm with "Next".

4. In the next window a search is performed for the new driver. Select the floppy

drive or the CD-ROM drive to install the FREECOM driver. Click on "Next".

5. The driver is loaded from the diskette/CD. Click on "Next" to continue the

installation.

6. After completion of the installation, click on "Finish". Your FREECOM drive

appears with a new drive letter under "My Computer". The installation is then

complete.

Uninstalling the FREECOM HighSpeed Driver

To uninstall the FREECOM HighSpeed driver, select the file "DriverRemove.exe" on

the installation diskette/CD and follow the on-screen instructions.

Software installation

FREECOM CABLE II PCMCIA / CABLE II CardBus

Windows 98 Default Driver

No driver software is required to install the Windows default driver.

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. The window "Hardware Installation Wizard" opens. Your FREECOM Cable II

PCMCIA is recognized as "Standard IDE/ESDI Hard Disk Controller". Confirm

with "Next" to continue the installation.

3. In the next window the option for finding the best driver for the device has

been selected. Confirm with "Next".

4. In the next window a search is performed for the new driver. Click on "Next"

to install the Windows default driver.

5. In the next window, click on "Finish" to conclude the driver installation. Your

FREECOM drive now appears with a new drive letter under "My Computer".

Later Installation of the FREECOM HighSpeed Driver Windows 98/ME

Note: If you are not prompted to install the driver, your system has

automatically installed the Windows default driver for your FREECOM

Cable II PCMCIA.

To install the FREECOM HighSpeed driver, proceed as follows:

1. Plug the FREECOM Cable II PCMCIA into the PCMCIA slot of your PC.

2. Open the "Device Manager" by right-clicking on the "My Computer" icon. A

menu opens. Select "Properties" and click on the "Device Manager" tab.

3. Click on the "+" next to the entry "Hard disk controllers".

4. Double-click on "Standard IDE/ESDI Hard Disk Controller".

5. Open the "Driver" tab. Then click on "Update Driver".

6. The "Update Device Driver Wizard" opens. Click on "Next".

7. In the next window the default is selected for finding a better driver than that

currently being used. (Recommended.) Confirm with "Next".

8. Now you can select where the FREECOM HighSpeed driver is to be installed.

Insert the FREECOM driver diskette/CD and select the floppy drive or the CD-

ROM drive. Confirm with "Next".

9. The FREECOM HighSpeed driver is then searched. Confirm the selection

afterwards with "Next". The FREECOM HighSpeed driver is now installed.

10. After completion of the installation, click on "Finish". Your FREECOM drive

appears with a new drive letter under "My Computer". The installation is then

complete.

Ce manuel convient aux modèles suivants

Autres manuels Freecom Matériel informatique

Freecom

Freecom DLT-VS-160 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur