Fluke DTX-CLT CertiFiber Manuel utilisateur

PN 3565770 January 2010, Rev. 1 5/10

All product names are trademarks of their respective companies.

DTX-CLT CertiFiber®

Optical Loss Test Set

Getting Started Guide

The DTX-CLT CertiFiber Optical Loss Test Set is a rugged, hand-held

instrument used to certify, troubleshoot, and document fiber

cabling installations.

Accessing the Product Manuals

This guide provides basic information to help you get started using

the tester. For more detailed information, see the latest versions of

the DTX-CLT CertiFiber Users Manual and the DTX Series Technical

Reference Handbook provided on the DTX-CLT CertiFiber Product

Manuals CD and on the Fluke Networks website.

WWarningX

To avoid possible fire, electric shock, personal injury,

damage to equipment, or inaccurate test results, read the

safety information in the DTX-CLT CertiFiber Users

Manual before using the tester.

Power the Tester

•

You may power the tester with the ac adapter included or with

the removable lithium ion battery pack.

•

You may charge the battery when it is attached or detached

from the tester (Figure 1).

•

The battery charges fully in about 4 hours with the tester off. A

fully-charged battery lasts for at least 12 hours of typical use.

gfa01.eps

Figure 1. Charging the Battery (left) and

Removing the Battery (right)

Prepare to Save Tests

•

Check the memory space available:

Turn the rotary switch to SPECIAL FUNCTIONS; then select

Memory Status.

•

Select a cable ID source:

You can select IDs from a pre-generated list or create an ID after

each test. Turn the rotary switch to SETUP, select Instrument

Settings, select Cable ID Source; then select a source.

•

Set up a job folder:

On the Instrument Settings menu select Current Folder. Select

an existing folder or press JCreate Folder to create a new

folder.

•

Enter job information:

On the Instrument Settings menu press Cto show the tab with

the Operator, Site, and Company names. To enter a new name,

select a setting, press JCreate; then use the softkeys, BC

AD, and Hfor editing. Press Nwhen you are

finished.

Clean and Inspect All Connectors

WCaution

When using the fiber modules, use proper procedures to

clean and inspect all fiber connectors before every use.

Neglecting this step or using improper procedures can cause

unreliable test results and may permanently damage the

connectors. See the Users Manual for instructions.

Set the Reference

The reference serves as the baseline power level for loss

measurements.

Set the reference at these times:

•

At the beginning of each day using the remote end setup you

will use that day.

•

Anytime you reconnect a test reference cord to the module’s

output or other source.

•

Anytime the tester warns you that the reference is out of date.

•

Anytime you see a negative loss measurement. (See the

Technical Reference Handbook for more information.)

•

Anytime the tester tells you to set the reference.

To set the reference

Turn on the tester and smart remote and let them sit for 5

minutes. Allow additional time if the modules have been

stored above or below ambient temperature.

Turn the rotary switch to SETUP, then select Fiber Loss. Set the

following on the Fiber Loss tabs (press Cto see other tabs):

•

Test Limit: Select the test limit required for the job. Press

JMore to see other lists of limits.

•

Fiber Type: Select the fiber type to be tested.

•

Remote End Setup: Set to Smart Remote.

•

Bi-directional: Enable this if you are required to test the

fiber in both directions.

•

Number of Adapters and Number of Splices: Enter the

number of adapters and splices that will be added to each

direction of the fiber path after the reference is set.

•

Connector Type: Select the connector type used in the

cabling to be tested. Select General if the exact type is not

listed.

•

Test Method: Select 1 Jumper if you use the reference and

test connection shown in this manual.

Turn the rotary switch to SPECIAL FUNCTIONS, then select Set

Reference.

The Set Reference screen shows reference connections for the

test method you selected. Figure 2 shows Smart Remote mode.

Clean and inspect the connectors on the testers and test

reference cords, connect the tester and smart remote; then

press P.

gfa02.eps

Figure 2. Setting the Reference in Smart Remote Mode

(1 Jumper Method)

Make Sure Your Test Reference Cords are

Good

Disconnect the test reference cords from the INPUT ports on the

tester and smart remote.

Make the connections shown in Figure 3.

Turn the rotary switch to AUTOTEST, then press P.

Press Hto see the test results. The results for each fiber

(Input Fiber and Output Fiber) must be no more than these

limits:

WCaution

An overall result of PASS does not show that the test

reference cords are good. You must compare the loss to

the limits given here to make sure the cords are good.

Multimode test reference cord:

850 nm: 0.11 dB or less

1300 nm: 0.10 dB or less

(The limits are different because fiber has more loss at 850 nm

than at 1300 nm.)

Singlemode test reference cord:

0.20 dB or less for 1310 nm and 1550 nm

If a result is more than the limit shown above, use the procedure

given in the Users Manual to test the cords in the path that

failed (Input Fiber or Output Fiber). When you have good test

reference cords, set the reference and do these steps again

before you test a fiber link.

Save the test results to show that you used good test reference

cords to test the link.

Note

Fluke Networks recommends that you use this procedure

to make sure your test reference cords are good before

you test each fiber link.

gfa03.eps

Figure 3. Testing the Test Reference Cords in

Smart Remote Mode

Do a Test

Connect to the fiber you will test. Figure 4 shows Smart Remote

mode.

Turn the rotary switch to AUTOTEST, then press P.

gda04.eps

Figure 4. Testing a Fiber Link in Smart Remote Mode

(1 Jumper Method)

Registration

Registering your product with Fluke Networks gives you access to

valuable information on product updates, troubleshooting tips, and

other support services.

To register, fill out the online registration form on the Fluke

Networks website at www.flukenetworks.com/registration.

Contacting Fluke Networks

www.flukenetworks.com

support@flukenetworks.com

+1-425-446-4519

•

Australia: 61 (2) 8850-3333 or 61 (3) 9329-0244

•

Beijing: 86 (10) 6512-3435

•

Brazil: 11 3759 7600

•

Canada: 1-800-363-5853

•

Europe: +31-(0) 40 2675 600

•

Hong Kong: 852 2721-3228

•

Japan: 03-6714-3117

•

Korea: 82 2 539-6311

•

Singapore: 65 6799-5566

•

Taiwan: (886) 2-227-83199

•

USA: 1-800-283-5853

Visit our website for a complete list of phone numbers.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Fluke Networks mainframe products will be free from defects in

material and workmanship for one year from the date of purchase.

Parts, accessories, product repairs and services are warranted for 90

days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries,

cables or other peripherals are all considered parts or accessories.

This warranty does not cover damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other warranty

on Fluke Networks’ behalf. To obtain service during the warranty

period, contact your nearest Fluke Networks authorized service

center to obtain return authorization information, then send your

defective product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,

SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR

IMPLIED. FLUKE NETWORKS IS NOT LIABLE FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY.

Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

Fluke Networks

PO Box 777

Everett, WA 98206-0777

USA

4/04

Autres manuels pour DTX-CLT CertiFiber

Table des matières

Autres manuels Fluke Équipement de test

Fluke

Fluke 2AC VoltAlert Manuel d'instructions

Fluke

Fluke NX2 Manuel utilisateur

Fluke

Fluke MS2-100-IE Manuel utilisateur

Fluke

Fluke NetTool II Series Manuel utilisateur

Fluke

Fluke 753 Manuel utilisateur

Fluke

Fluke 810 Manuel utilisateur

Fluke

Fluke CopperPro 990 Manuel utilisateur

Fluke

Fluke CertiFiber Pro CFP2-100-QI Manuel utilisateur

Fluke

Fluke FEV300 Instructions originales

Fluke

Fluke Versiv Series Manuel d'utilisation et d'entretien

Fluke

Fluke 9102S Manuel utilisateur

Fluke

Fluke TS22 Manuel utilisateur

Fluke

Fluke 754 Manuel utilisateur

Fluke

Fluke 5520A Service Manuel

Fluke

Fluke 5500A Manuel utilisateur

Fluke

Fluke 9103 Manuel utilisateur

Fluke

Fluke HART 744 Manuel utilisateur

Fluke

Fluke 5502A Manuel utilisateur

Fluke

Fluke ScopeMeter 190B Series Manuel utilisateur

Fluke

Fluke 9640A Series Manuel utilisateur

Fluke

Fluke AIRCHECK Manuel utilisateur

Fluke

Fluke 715 Manuel utilisateur

Fluke

Fluke OMNIScanner 2 Manuel utilisateur

Fluke

Fluke 5080A Manuel de la liste des pièces

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur