Fluke I1000s Guide de configuration

Manual Supplement

Manual Title: i1000s Calibration Supplement Issue: 1

Part Number: 1574933 Issue Date: 7/01

Print Date: May 2001 Page Count: 2

Revision/Date:

This supplement contains information necessary to ensure the accuracy of

the above manual. Enter the corrections in the manual if either one of the

following conditions exist:

1. The revision letter stamped on the indicated PCA is equal to or higher

than that given with each change.

2. No revision letter is indicated at the beginning of the change.

i1000s Calibration Manual Supplement

7/01 1

Change #1

On page 8, Table 4, under Recommended Model,

Replace:

Digital Multimeter Hp 3458A or equivalent

With:

Digital Multimeter Agilant 3458A or equivalent

Delete the following from Table 4,

AC/DC Shunt IET Labs-DCCS-200 0.1e- 0.1% non-inductive

Replace the entire

Phase Shift

section, Table 5 and Figure 3 with the following:

Phase Shift Test

To check Phase Shift performance, set up the equipment as shown in Figure 3.

1. Center the Current Probe around the coil.

2. Set the calibrator output to 1V (phase meter reference input), 1A and 50 Hz, per step 1 of Table 5.

Performance Test Steps.

3. Verify that the phase meter reading is within the “Phase in Deg” limits of Table 5.

Table 5. Performance Test Steps

i1000s

mV Output Phase in Deg.

Step Coil Range 5520A

Output

5500A

Coil

I. Prim. Freq. Min. Max. Min. Max.

1 50 turn 1 mV/A 1 A 50.0 A 50 Hz 48.5 51.5 -3.0 3.0

2 50 turn 1 mV/A 2 A 100 A 400 Hz 98.0 102.0 N/A N/A

3 50 turn 1 mV/A 4 A 200 A 60 Hz 197.0 203.0 -2.0 2.0

4 50 turn* 1 mV/A 14 A 700 A 50 Hz 692.0 708.0 -2.0 2.0

5 1 turn 10 mV/A 5 A N/A 50 Hz 44.0 56.0 -15.0 15.0

6 50 turn 10 mV/A 0.4 A 20 A 50 Hz 191.0 209.0 -10.0 10.0

7 50 turn 10 mV/A 2 A 100 A 50 Hz 975.0 1025.0 -10.0 10.0

8 1 turn 100 mV/A 0.50 A N/A 50 Hz 38.5 61.5 N/A N/A

9 1 turn 100 mV/A 2.00 A N/A 50 Hz 184.0 216.0 -15.0 15.0

10 1 turn 100 mV/A 10 A N/A 50 Hz 960.0 1040.0 -15.0 15.0

* 700 A/ 50 Hz in 1 mV/A range has a TUR of 3.3

4. Continuing to use 1V as the phase meter reference input, set the calibrator output for the remaining

steps listed in Table 5. Steps 2 and 8 do not require phase tests.

5. Verify that the phase meter readings meet the "Phase in Deg" limits for each step.

Manual Supplement i1000s Calibration

27/01

0•

123

456

789

ENTER

mVHz

FIELD

EDIT

OPRSTBY EARTH SCOPE

EXGRD MENU

SHIFT

RESET

SETUP

REF

NEW

MEAS

¡F

dBm sec

¡C

POWER

MULT

DIV

MODES

5520A

CALIBRATOR

TRIG

GUARD

20A

NORMAL AUX SCOPE

OUT

V, , ,RTD A, -SENSE, AUX V

20V PK MAX

mV Output

Black

Red

5520A calibrator

Phase meter

1 turn coil

5500A/coil

Tie Aux Com and

Normal Com together

using heavy gauge

wire or bus bar.

akp03f.eps

Figure 3. Phase Check Setup

mV Output Test

1. Connect the equipment as shown in Figure 5.

2. Set the calibrator output and coil for each step of Table 5.

3. Verify that the voltmeter reading is within the “i1000S mV Output” limits of Table 5.

Autres manuels pour i1000s

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke 43 Manuel utilisateur

Fluke

Fluke 323 Manuel utilisateur

Fluke

Fluke RF303 Operators Manuel utilisateur

Fluke

Fluke 1630-2 Manuel utilisateur

Fluke

Fluke 789 Manuel utilisateur

Fluke

Fluke DTX-1800 Manuel d'utilisation et d'entretien

Fluke

Fluke i400s Manuel d'utilisation et d'entretien

Fluke

Fluke 1520 Manuel utilisateur

Fluke

Fluke NORMA 4000 Operators Manuel utilisateur

Fluke

Fluke VIBXPERT II Manuel utilisateur

Fluke

Fluke ProcessMeter 787B Manuel utilisateur

Fluke

Fluke 365 Manuel utilisateur

Fluke

Fluke RUSKA 2465A-754 Manuel utilisateur

Fluke

Fluke 481 Manuel utilisateur

Fluke

Fluke 972A Manuel utilisateur

Fluke

Fluke ScopeMeter 190 II 190-104 Manuel utilisateur

Fluke

Fluke FiberInspector FT500 Manuel utilisateur

Fluke

Fluke Biomedical IDA-4 Plus Operators Manuel utilisateur

Fluke

Fluke i430-Flexi-TF-II Manuel utilisateur

Fluke

Fluke 845AR Manuel utilisateur

Fluke

Fluke IntelliTone Pro 200 LAN Manuel utilisateur

Fluke

Fluke ScopeMeter 123 Manuel utilisateur

Fluke

Fluke 700G01 Manuel utilisateur

Fluke

Fluke 416D Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Fluke i1000s Guide de configuration

Manuels Instrument de mesure populaires d'autres marques