Fluke CertiFiber Pro Manuel utilisateur

PN 4343722 (English) May 2013, Rev. 1 12/2013

2013 Fluke Corporation

All product names are trademarks of their respective companies.

*4343722*

CertiFiber®Pro

Optical Loss Test Set

Getting Started Guide

The CertiFiber Pro Optical Loss Test Set (OLTS) modules attach to

Versiv™main and remote units to make rugged, hand-held

testers that let you certify, troubleshoot, and document fiber

optic network cabling.

Accessing the Product Manuals

This guide provides basic information to help you get started

using the tester. For more detailed information, see the latest

versions of the CertiFiber Pro Users Manual and the Versiv

Technical Reference Handbook provided on the Product

Manuals DVD and on the Fluke Networks website.

Safety Information

Warning

To prevent possible fire, electric shock, or personal injury:

•

Read all safety information before you use the

Product.

•

Carefully read all instructions.

•

Do not open the case. You cannot repair or replace

parts in the case.

•

Do not modify the Product.

Warning or Caution: Risk of damage or destruction to

equipment or software. See explanations in the manuals.

Warning: Risk of fire, electric shock, or personal injury.

Warning: Class 1 or Class 2 lasers. Risk of eye damage

from hazardous radiation.

This key turns the Product on and off.

•

Use only replacement parts that are approved by

Fluke Networks.

•

Do not touch voltages > 30 V AC rms, 42 V AC peak,

or 60 V AC.

•

Do not use the Product around explosive gas, vapor,

or in damp or wet environments.

•

Use this Product indoors only.

•

Use the Product only as specified, or the protection

supplied by the Product can be compromised.

•

Do not use and disable the Product if it is damaged.

•

Do not use the Product if it operates incorrectly.

•

Batteries contain hazardous chemicals that can

cause burns or explode. If exposure to chemicals

occurs, clean with water and get medical aid.

•

Remove the batteries if the Product is not used for

an extended period of time, or if stored in

temperatures above 50 °C. If the batteries are not

removed, battery leakage can damage the Product.

•

The battery door must be closed and locked before

you operate the Product.

•

Repair the Product before use if the battery leaks.

•

Recharge the batteries when the low battery

indicator shows to prevent incorrect measurements.

•

Do not disassemble or crush battery cells and

battery packs.

•

Do not put battery cells and battery packs near heat

or fire. Do not put in sunlight.

•

Have an approved technician repair the Product.

•

For Products with rechargeable batteries, use only

AC adapters approved by Fluke Networks for use

with the Product to supply power to the Product

and charge the battery.

Warning: Class 1 and Class 2

Laser Products

To prevent eye damage and personal injury:

•

Do not look directly into optical connectors. Some

optical equipment emits invisible radiation that can

cause permanent damage to your eyes.

•

Keep the module’s OUTPUT ports covered with a

dust cap or keep a test reference cord attached. The

OUTPUT ports can emit radiation even when you do

not do a test.

•

Do not look into the laser. Do not point laser

directly at persons or animals or indirectly off

reflective surfaces.

•

When you inspect fiber endfaces, use only

magnification devices that have the correct filters.

•

Use the Product only as specified or hazardous laser

radiation exposure can occur.

Caution

To prevent damage to the Product or cables under test and to

prevent data loss, read all safety information given in all

documentation supplied with the Product.

Connectors, Keys, and LEDs

HGP00.EPS

Figure 1. Connectors, Keys, and LEDs



LCD display with touchscreen.



Singlemode output port with removable connector adapter

and dust cap. This port transmits optical signals for loss and

length measurements.

The LED below the output port is red when the port transmits

1310 nm and green for 1550 nm.



Input port with removable connector adapter and dust cap.

This port receives optical signals for loss, length, and power

measurements.



Multimode output port with removable connector adapter and

dust cap. This port transmits optical signals for loss and length

measurements.

The LED below the output port is red when the port transmits

850 nm and green for 1300 nm.



Universal fiber connector (with dust cap) for the visual fault

locator. The connector accepts 2.5 mm ferrules. The LED below

the connector shows the locator’s mode.



Button to manually control the output ports (



and



) and

the visual fault locator (





Micro-AB USB port: This USB port lets you connect the tester to

a PC so you can upload test results to the PC (main tester only)

and install software updates in the tester.



Type A USB port: This USB host port lets you save test results on

a USB flash drive or connect a video probe to the tester.



Headset jack.



: Starts a test. To start a test, you can also tap TEST on the

display.



Power key.



: Press to go to the home screen.



Connector for the AC adapter.



RJ45 connector: For functions available in future software

releases.



PASS LED comes on when a test passes.

TEST LED comes on during a test and when you manually turn

on one of the output ports.

FAIL LED comes on when a test fails.

TALK LED comes on when the talk function is on (see



TONE LED flashes if you press and the main tester is not

connected to the remote or is in Far End Source mode.

LOW BATTERY LED comes on when the battery is low.



: Press to use the headset to speak to the person

at the other end of the link. Press again to adjust the volume.

To turn off the talk function, hold down .

How to Certify Fiber Optic Cabling

Power the Tester

Charge the battery if necessary. Connect the AC adapter to

AC power and to the adapter connector () shown in

Figure 1. You can use the tester while the battery charges.

Select Settings

2-1 On the home screen, tap the test setup panel (Figure 2).

2-2 On the CHANGE TEST screen, tap a fiber test, then tap

EDIT.

2-3 On the TEST SETUP screen, tap the panels to change

settings:

•

Test Type: Select Smart Remote.

•

Bi-Directional: Select On. The tester will do fiber tests in

both directions.

•

Fiber Type: Select a fiber type that is correct for the type

you will test.

•

Test Limit: Select General Fiber Optic.

•

Reference Method: Select 1 Jumper Reference.

•

No. of Connectors/Splices: These settings are only for test

limits that use a calculated limit for loss. They are not

applicable to the General Fiber Optic limit.

2-4 To save the settings, tap SAVE on the TEST SETUP screen.

Figure 2. Panels on the Home Screen

HGP01.EPS



To set up a project, tap the PROJECT panel.



To change settings for the test or select a different test, tap

the test setup panel.



To set up cable IDs and turn on Auto Save, tap the Next ID

panel.



To enter the operator name, tap the Operator panel.



To set the reference and verify your test reference cords for

loss/length tests, tap SET REF.

Clean and Inspect All Connectors

Caution

Use proper cleaning procedures to clean all fiber

connectors before every use. Neglecting this step or using

improper procedures can cause unreliable test results and

may permanently damage the connectors. See the Users

Manual for instructions.

Set the Reference and Verify Your Test Reference

Cords

The reference procedure for fiber cable sets a baseline power

level for loss measurements. It is important to set the reference

frequently. You must also make sure your test reference cords

are in good condition. See the Users Manual.

4-1 Turn on the tester and remote and let them sit for a

minimum of 5 minutes. Let them sit longer if they are

above or below ambient temperature.

4-2 Make sure that the home screen shows the correct settings

4-3 Clean and inspect the connectors on the tester, remote,

and test reference cords.

4-4 On the home screen tap SET REF.

4-5 On the SET REFERENCE screen, tap RUN WIZARD.

4-6 Make the connections shown on the screen, then tap

NEXT to see the completed connections (Reference in

Figure 3).

Note

When you set the reference, align the testers as

shown in Figure 3 to keep the fibers as straight

as possible.

4-7 To enter the length of the test reference cords you will

add to connect to the link, tap TRC LENGTH on the SET

REFERENCE screen. The length you enter does not change

the test results. The tester saves the length with the results

to meet TIA reporting requirements.

4-8 Tap SET REFERENCE, tap NEXT, then make the

connections shown on the screen (TRC Verification in

Figure 3)

4-9 Tap TRC VERIFICATION. The tester measures and saves the

loss of the test reference cords you added.

Make Connections and Do a Test

5-1 Tap NEXT. Connect the testers to the link as shown on

the screen (Fiber Link Test in Figure 3).

5-2 Press on the main or remote tester.

GPU122.EPS

Figure 3. Connections for Smart Remote Mode

(1 Jumper Reference, Multimode Fiber)

Examine the Results

The tester shows a summary of the test results for the fibers

(Figure 4, left). To see more information (Figure 4, right), tap

the window for a fiber.

Caution

Do not disconnect the

outputs ( and ) after

you set the reference.

When you use the EF-TRCs,

DO NOT use other mandrels.

Test

reference

cord

Fiber

link

Test

reference

cord

Reference

TRC Verification Fiber Link Test

* Use the EF-TRCs only with multimode modules.

HGP02.EPS

Figure 4. Examples of Fiber Test Results Screens

Save the Results

•

If Auto Save is on, the tester uses the next two IDs to save

the results for the two fibers.

•

If Auto Save is off, tap SAVE if the test passed or FIX LATER

if the test failed. The SAVE RESULT screen shows the next

two IDs available. You can change the IDs if necessary.

The tester saves the results in the DEFAULT project, unless you

selected a different project.

About Projects

You can set up a project to specify the settings and tests

necessary for a job, monitor the status of a job, and organize the

test results.

To start a new project, tap PROJECT on the home screen, tap

CHANGE PROJECT, then tap NEW PROJECT. See the Users Manual

or Technical Reference Handbook on the DVD for more

information.

Registration

Registering your product with Fluke Networks gives you access

to valuable information on product updates, troubleshooting

tips, and other support services. To register, use LinkWare

software.

Contact Fluke Networks

www.flukenetworks.com

support@flukenetworks.com

1-800-283-5853, +1-425-446-5500

Fluke Networks operates in more than 50 countries worldwide.

For more contact information, go to our website.

General Specifications

Certifications and Compliance

Battery Type Lithium-ion

Temperature Operating: -18 °C to +45 °C

Storage: -30 °C to +60 °C

Altitude Operating: 4,000 m (3,200 m with AC adapter)

Storage: 12,000 m

Conformite Europeene. Conforms to the

requirements of the European Union and the

European Free Trade Association (EFTA).

Listed by the Canadian Standards Association.

Conforms to relevant Australian standards.

Conforms to relevant Russian standards.

KCC-REM-FKN-012001001: EMC approval for Korea

Class A Equipment (Industrial Broadcasting &

Communication Equipment)

This product meets requirements for industrial (Class

A) electromagnetic wave equipment and the seller or

user should take notice of it. This equipment is

intended for use in business environments and is not

to be used in homes.

A급기기 ( 업무용 방송통신기자재 )

이기기는 업무용 (A 급) 전자파적합기기로서 판매자 또

는사용자는 이점을 주의하시기 바라며 , 가정외의 지역

에서 사용하는 것을 목적으로합니다 .

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Fluke Networks mainframe products will be free from defects in

material and workmanship for one year from the date of purchase.

Parts, accessories, product repairs and services are warranted for 90

days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries,

cables or other peripherals are all considered parts or accessories.

This warranty does not cover damage from accident, neglect, misuse,

alteration, contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other warranty

on Fluke Networks’ behalf. To obtain service during the warranty

period, contact your nearest Fluke Networks authorized service

center to obtain return authorization information, then send your

defective product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,

SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR

IMPLIED. FLUKE NETWORKS IS NOT LIABLE FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,

ARISING FROM ANY CAUSE OR THEORY.

Since some states or countries do not allow the exclusion or

limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

Fluke Networks

PO Box 777

Everett, WA 98206-0777

USA

4/04

Autres manuels pour CertiFiber Pro

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke 279 FC Manuel utilisateur

Fluke

Fluke 3310-PR-TF-II Manuel utilisateur

Fluke

Fluke FiberInspector FT500 Manuel utilisateur

Fluke

Fluke endurance series Manuel utilisateur

Fluke

Fluke 43B Guide de l'utilisateur

Fluke

Fluke MDA-550 Manuel utilisateur

Fluke

Fluke 360 Manuel d'instructions

Fluke

Fluke OptiView Manuel utilisateur

Fluke

Fluke 1750/ET Manuel utilisateur

Fluke

Fluke NORMA 6003 Manuel de la liste des pièces

Fluke

Fluke 3000 FC Manuel utilisateur

Fluke

Fluke 323 Manuel utilisateur

Fluke

Fluke 9100A Series Manuel utilisateur

Fluke

Fluke ScopeMeter 123 Manuel utilisateur

Fluke

Fluke 317 Manuel utilisateur

Fluke

Fluke 377 Manuel d'utilisation et d'entretien

Fluke

Fluke OptiView FiberInspector OPV-FT600 Manuel utilisateur

Fluke

Fluke i400s Manuel d'utilisation et d'entretien

Fluke

Fluke 381 Manuel utilisateur

Fluke

Fluke C9970 Manuel utilisateur

Fluke

Fluke i3000s Flex Series Manuel utilisateur

Fluke

Fluke 80K-4 Manuel utilisateur

Fluke

Fluke 421D Manuel utilisateur

Fluke

Fluke NORMA 6003 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur