Fluke 726 Guide de configuration

Manual Supplement

Manual Title: 726 Users Supplement Issue: 2

Print Date: September 2005 Issue Date: 3/08

Revision/Date: Page Count: 6

This supplement contains information necessary to ensure the accuracy of the

above manual. This manual is distributed as an electronic manual on the

following CD-ROM:

CD Title: 725/726

CD Rev. & Date: 4, 9/2005

CD PN: 1549615

726 Users Manual Supplement

3/07 1

Change #1

On page 2, replace the Pulse row with the following:

Pulse 1-100,000

Frequency Max 15 kHz

1-10,000

Frequency Range 2 CPM to 15 kHz

On page 12, Table 4, replace the Description for Number Lwith the following:

Cycles through:

ESlow repeating 0 % - 100 % - 0 % ramp

PConfigurable repeating 0 % - 100 % - 0% ramp

NConfigurable repeating 0 % - 100 % - 0 % ramp in 25 % steps

LUsed for the pulse train and totalizer functions.

On page 13, replace Figure 4 with the following:

Manual Supplement 726 Users

2 3/07

Low Battery

Symbol

Loop

Indicator

Memory Locations

for Calibrator Setups

Units

Display

Auto

Ramp

Mode

Indicator

HART Mode

Indicator

% Error

Indicators

Figure 4. Elements of a Typical Display

726 Users Manual Supplement

3/07 3

On page 14, under Configuration Menus, add the following under the last bullet:

•Step time

•Ramp time

On page 15, under Shut Down Mode, replace numbered steps with the following:

1. Press Cuntil SHUT DOWN appears on the display.

2. Use Xand Wto increase or decrease the time.

3. Use Yand Zto turn on and off.

4. Press Sto save the setting.

On page 16, under Hart®Resistor ON/OFF, replace step 2 with the following:

2. Use Vor Yand Zto toggle ON and OFF.

Add the following below the Note:

Step Time

Step Time sets the ramp step Ntime from 1 sec to 99 sec.

1. Press Cuntil STEP TIME appears on the display.

2. Use Xand Wto set the step time.

3. Press Sto save the setting.

Manual Supplement 726 Users

4 3/07

Ramp Time

Ramp Time sets the ramp Ptime from 5 sec to 99 sec.

1. Press Cuntil RAMP TIME appears on the display.

2. Use Xand Wto set the ramp time.

3. Press Sto save the setting.

On page 25, Table 6, add the following:

Cu10 10 ΩCopper 0.0042 Ω/°C -100 to 250

On page 42, under Auto Ramping the Output, replace the 2nd and 3rd bullets with the following:

•P0 % - 100 % - 0 % configurable time smooth ramp. Set ramp time using configuration

menu.

•N0 % - 100 % - 0 % Stair-step ramp in 25 % steps, pausing at each step. Set ramp

time using configuration menu. Steps are listed in Table 7.

On page 60, under Frequency Measurement, add the following to the bottom of the table:

Sensitivity: 1 V peak to peak minimum

Waveform: Squarewave

726 Users Manual Supplement

3/07 5

On page 62, change the Range entries for “Thermocouple in mV read” and “Thermocouple in

mV source”:

From:

-10 °C to 75 °C

To: -10 mV to 75 mV

On page 63, under the RTD Accuacy (Read and Source) (ITRS-90) table, replace the CU10 row

with the following:

Cu10 -100.0 250.00 1.8

On page 64, under Pulse Read and Pulse Source, replace the Frequency entry with the

following:

2 CPM to 15 kHz

Manual Supplement 726 Users

6 3/08

Change #2

On page 7, Table 2, add the following:

;Conforms to Australian C-Tick directives

Autres manuels pour 726

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke 175 Manuel utilisateur

Fluke

Fluke FOM Manuel utilisateur

Fluke

Fluke OptiView T1/E1 Manuel utilisateur

Fluke

Fluke 831 Manuel utilisateur

Fluke

Fluke CableAnalyzer DSX-5000 Manuel utilisateur

Fluke

Fluke CO-220 Manuel utilisateur

Fluke

Fluke 165X Manuel utilisateur

Fluke

Fluke FOM Instructions d'utilisation et d'installation

Fluke

Fluke 789 Manuel utilisateur

Fluke

Fluke BT21ANG Manuel utilisateur

Fluke

Fluke 845AR Manuel utilisateur

Fluke

Fluke a3001 FC Manuel utilisateur

Fluke

Fluke DPM2 Plus Manuel utilisateur

Fluke

Fluke TPS FLEX 18-TF-II Guide de configuration

Fluke

Fluke OptiView FiberInspector OPV-FT600 Manuel utilisateur

Fluke

Fluke 1520 Manuel utilisateur

Fluke

Fluke 481-DESI Manuel utilisateur

Fluke

Fluke CO-205 Manuel utilisateur

Fluke

Fluke Reliable Power Meters 1941 Manuel utilisateur

Fluke

Fluke 9190A Manuel utilisateur

Fluke

Fluke i3000s Flex Series Manuel utilisateur

Fluke

Fluke 323 Manuel utilisateur

Fluke

Fluke 35040 Operators Manuel utilisateur

Fluke

Fluke 165X Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur