Fluke 374 Manuel utilisateur

PN 3608883

July 2010 Rev. 1, 3/23

All product names are trademarks of their respective companies.

374/375

376/376-II

Clamp Meter

LIMITED WARRANTY AND LIMITATION OF LIABILITY

The Fluke 374/375/376 products will be free from defects in material and workmanship

for 3 years from the date of purchase. The Fluke 376-II product will be free from

defects in material and workmanship for 5 years from the date of purchase. This

warranty does not cover fuses, disposable batteries, or damage from accident,

neglect, misuse, alteration, contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf.

To obtain service during the warranty period, contact your nearest Fluke authorized

service center to obtain return authorization information, then send the product to that

Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS

FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE

IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR

THEORY. Since some states or countries do not allow the exclusion or limitation of an

implied warranty or of incidental or consequential damages, this limitation of liability

may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Table of Contents

Title Page

Introduction ............................................................................................................. 1

Contact Fluke .......................................................................................................... 2

Safety Information ................................................................................................... 2

The Meter................................................................................................................ 8

Specifications .......................................................................................................... 18

General Specifications......................................................................................... 18

Accuracy Specifications....................................................................................... 20

374/375/376/376-II

Users Manual

Introduction

Warning

Read "Safety Information" before you use the Meter.

The Fluke 374/375/376/376-II (the Meter) measure true-rms ac current and voltage, dc current

and voltage, inrush current, resistance, and capacitance. The 375/376/376-II also measure

frequency and dc millivolts. The detachable iFlex (Flexible Current Probe) that is included with the

376/376-II (optional with the 374/375) expands the measurement range to 2500 A ac. The

Flexible Current Probe provides increased display flexibility and allows measurements of

awkward sized conductors and improved wire access. The illustrations in this manual show the

376.

374/375/376/376-II

Users Manual

Contact Fluke

Fluke Corporation operates worldwide. For local contact information, go to our website:

www.fluke.com

To register your product, or to view, print, or download the latest manual or manual supplement,

go to our website: www.fluke.com/productinfo.

+1-425-446-5500 fluke-[email protected]

Safety Information

A Warning identifies conditions and actions that pose hazard(s) to the user. A Caution identifies

conditions and procedures that could cause Meter damage, equipment under test damage, or

permanent loss of data.

Symbols used on the Meter and in this manual are explained in Table 1.

Clamp Meters

Safety Information

Warning

To prevent possible electrical shock or personal injury, follow these guidelines:

•Use the Meter only asspecified in this manual or the protection provided by the

Meter can becompromised.

•Examine the case before you use the Meter. Look for cracks or missing plastic.

Carefully look at the insulation around the connectors.

•Never measure current while the test leads are inserted into the input jacks.

•Make sure the battery door is closed and latched before operating the Meter.

•Remove the test leads from the Meter before the battery door is opened.

•Examine the test leads for damaged insulation orexposed metal. Check test lead

continuity. Replace damaged test leads before usingthe Meter.

•Do not use the Meter if itoperates incorrectly. Protection can be compromised.

When indoubt, have the Meter serviced.

•Do not use the Meter around explosive gas, vapor orindamp or wet

environments.

•Use only type AA batteries, properly installed in the Meter case,topower the

Meter.

•When measuring current with the Jaw, keep fingers behind the Tactile Barrier.

See "The Meter"  .

•Measure a known voltage to verify product operation.

374/375/376/376-II

Users Manual

•Do not use in CAT III or CAT IV environments without the protective cap of test probe.

The protective cap decreases the expose probe metal <4 mm. This decreases the

possibility of arc flash from short circuits.

•To avoid false readings that can lead to electrical shock and injury, replace the

batteries as soon as the low battery indicator () appears.

•When batteries are changed, ensure that the calibration seal in the battery

compartment is not damaged. If damaged, the Meter may not be safe to use. Return

the Meter to Fluke for replacement of the seal.

•When servicing the Meter, use only specified replacement parts.

•Have the Meter serviced only by qualified service personnel.

•Be careful around voltages >30 V ac rms, 42 V ac peak, or 60 V dc. Such voltages

pose a shock hazard.

•Do not apply more than the rated voltage, as marked on the Meter, between the

terminals or between any terminal and earth ground.

•When using the probes, keep fingers behind the finger guards on the probes.

•Connect the common test lead before connecting the live test lead. When

disconnecting test leads, disconnect the live test lead first.

•Do not work alone so assistance can be rendered in an emergency.

•Use extreme caution when working around bare conductors or bus bars. Contact

with the conductor could result in electric shock.

Clamp Meters

Safety Information

•Adhere to local and national safety codes. Individual protective equipment must

be used to prevent shock and arc blast injury where hazardous live conductors

are exposed.

•Disconnect circuit power and discharge all high-voltage capacitors before you

measure resistance, continuity, or capacitance.

•For the 374 and 375, do not measure ac/dc current in circuits carrying more than

1000 V or 600 A with the Meter Jaw.

•For the 376/376-II, do not measure ac/dc current in circuits carrying more than

1000 V or 1000 A with the Meter Jaw.

•Never operate the Meter with the back cover removed or the case open.

•Do not measure ac current in circuits carrying more than 1000 V or 2500 A with

the Flexible Current Probe.

•Do not apply the Flexible Current Probe around or remove from HAZARDOUS

LIVE conductors.

•Do not use the flexible current sensor if the inner contrasting insulation color is

showing.

•Take special care during fitting and removal of the Flexible Current Probe. De-

energize the installation under test or wear suitable protective clothing.

374/375/376/376-II

Users Manual

Caution

To avoid possible damage to the Meter or to equipment under test:

•Use the proper jacks, function, and range for the measurement application.

•Clean the case and accessories with a damp cloth and mild detergent only.

Do not use abrasives or solvents.

Table 1. Symbols

Symbol Definition Symbol Definition



Consult user documentation. 

WARNING. RISK OF DANGER.

WARNING. HAZARDOUS

VOLTAGE. Risk of electric shock.



Conforms to European Union

directives.



DC (Direct Current)



AC (Alternating Current)



Earth



Double Insulated



Application around and removal

from uninsulated hazardous live

conductors is permitted.



Battery. Low battery when shown on

display.

Autres manuels pour 374

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fluke Instrument de mesure

Fluke

Fluke CableAnalyzer DTX-1500 Manuel utilisateur

Fluke

Fluke ProcessMeter 787 Manuel utilisateur

Fluke

Fluke Reliable Power Meters 1941 Manuel utilisateur

Fluke

Fluke 8050A Manuel utilisateur

Fluke

Fluke 5606 Manuel utilisateur

Fluke

Fluke 1773 Manuel utilisateur

Fluke

Fluke ScopeMeter 190-104 Manuel utilisateur

Fluke

Fluke 78 Manuel utilisateur

Fluke

Fluke a3001 FC Manuel d'utilisation et d'entretien

Fluke

Fluke CableAnalyzer DSX-5000 Manuel utilisateur

Fluke

Fluke BT520 Manuel utilisateur

Fluke

Fluke i6000s Flex Series Manuel utilisateur

Fluke

Fluke SigmaPace 1000 Manuel utilisateur

Fluke

Fluke 43 Manuel utilisateur

Fluke

Fluke Comark Diligence 600 Manuel utilisateur

Fluke

Fluke DTX-CLT CertiFiber Manuel utilisateur

Fluke

Fluke i400s-EL Manuel utilisateur

Fluke

Fluke 165X Manuel utilisateur

Fluke

Fluke FOM Instructions d'utilisation et d'installation

Fluke

Fluke 312 Manuel utilisateur

Fluke

Fluke 165X Manuel utilisateur

Fluke

Fluke v3000 FC Manuel utilisateur

Fluke

Fluke VT650 Manuel utilisateur

Fluke

Fluke 971 CAL Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur