FlowCon PIM-DP Manuel utilisateur

Figure 3









Measurement

Measure the ΔpCircuit on the p/t plugs



(figure 2)

while turning the adjustment . WAIT UNTIL

THE VALVE STABILIZES ITSELF.

Close off procedure

1. Turn the adjustment bolt under the cap 

(figure 2) clockwise to fully open position (max.

12.5 Nm).

2. Turn off the ball valve  (figure 2) by position-

ing the handle across the pipe and wait for at

least 1 minute.

3. Close the on/off bolt  (figure 2) all the way

by turning clockwise with a flat screwdriver on

DN65/80 (2 1/2”) or a 13 mm (1/2”) Allen key

on DN80/100 (3”/4”) and DN125/150 (5”/6”).

To open the valve, please follow steps 1 through

3 in reverse order.

Filter cleaning

1. Isolate the filter by turning the valve off (fol-

low the close off procedure).

2. Then remove the copper tubing by loosening

the connection nuts . Experiencing some

water leaking is possible due to downstream

pressure.

3. Remove the filter housing  and thereafter

remove the filter  with a sharp pick. BE

CAREFUL NOT TO DAMAGE ENLARGEN

THE FILTER.

4. Clean the filter and put it back in. It is recom-

mended also to inspect the flow restrictor for

blockage .

This paper is a supplement to the FlowCon General Instruction

Latest release of any FlowCon material is available on www.owcon.com

FlowCon PIM™-DP 65-150 mm (2 1/2”-6”)

1H95040 - 04/2020

Page 2 of 2

FlowCon International assumes no responsibility for mistakes, if any, in any printed material.

Installation and Operation Instruction

Figure 1

Figure 2



FlowCon PIM™-DP DN65-80 (2 1/2”-3”)

FlowCon PIM™-DP DN100 (4”)













FlowCon PIM™-DP DN125-150 (5”-6”)









The FlowCon PIM™-DP are available in three

different models covering six different sizes:

•FlowCon PIM™-DP DN65-80 (2 1/2”-3”)

•FlowCon PIM™-DP DN100 (4”)

•FlowCon PIM™-DP DN125-150 (5”-6”)

Installation

Prior to installing the FlowCon PIM™-DP (supplied

from factory in fully open position), the system

should be properly flushed.

Capillary tube

Do not damage the capillary tube by compressing

or bending the tube with a bending radius below

20 mm (3/4”). Capillary tube is to be finger

mounted and tightened with 1-3Nm - DO NOT

OVER TIGHTEN.

Air venting

It is important to release all air inside the valve.

Upon doing so open and close the partner valve

fully. It will make the diaphragm to fully extend

and contract and thereby remove all trapped air

inside. PUMP MUST BE OPERATIONAL FOR

THIS PROCEDURE TO BE EFFECTIVE AND

IT MUST BE CARRIED OUT AFTER THE

SYSTEM HAS BEEN VENTED.

Setting

After installation and air venting, the desired

ΔpCircuit is set by adjusting the setting  (figure

2) under the cap on top of the valve. Use a 13 mm

(1/2”) Allen key and NOTE: ADJUSTMENT

SHOULD BE DONE SLOWLY, APPROXIMA-

TELY ONE TURN EVERY 10 SEC. Increasing

the ΔpCircuit by turning clockwise and decrease

by turning counter-clockwise. To increase to

maximum ΔpCircuit (170 kPaD / 25 psid) turn the

setting approximately 15 full turns.

FlowCon PIM™-DP 65-150 mm (2 1/2”-6”)

1H95040 - 04/2020

This paper is a supplement to the FlowCon General Instruction

Latest release of any FlowCon material is available on www.owcon.com

Page 1 of 2

FlowCon International assumes no responsibility for mistakes, if any, in any printed material.

Autres manuels FlowCon Unité de contrôle

FlowCon

FlowCon ABM Manuel du propriétaire

FlowCon

FlowCon UniQ Manuel du propriétaire

FlowCon

FlowCon AHU Wafer Manuel du propriétaire

FlowCon

FlowCon SM.1.1 Manuel du propriétaire

FlowCon

FlowCon DPCV Manuel du propriétaire

FlowCon

FlowCon SH series Manuel du propriétaire

FlowCon

FlowCon Green Manuel du propriétaire

FlowCon

FlowCon S-JUST Manuel du propriétaire

FlowCon

FlowCon FlowCon Green Series Manuel du propriétaire

FlowCon

FlowCon EVS Manuel utilisateur

FlowCon

FlowCon Green.3 Series Manuel du propriétaire

FlowCon

FlowCon Green.3 DN40 Manuel du propriétaire

FlowCon

FlowCon SM 50-250mm Manuel du propriétaire

FlowCon

FlowCon SM.3.0 Manuel utilisateur

FlowCon

FlowCon Green Manuel du propriétaire

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur