Fimap ENJOY 360 Mode d’emploi
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 1 of 8
ADJUSTMENTS AND INSPECTIONS
READ THE OPERATING AND MAINTENANCE MANUAL
Testing the Electric System
1. Remove the battery connector.
2. Check that the battery connection cables are clean
and tight.
3. Check that the power cables are connected and
tight: batteries, connectors, remote control
switches (both in the electric system box and in the
suction head), motors etc.
4. Check the state of the thermal fuses:
Main 3,5 A
Suction 20 A
Brushes 25 A
Traction 60 A
5. Reconnect the battery connector.
6. Turn the key to turn the machine on.
7. Check signal lamps and switches:
Check that the key operates correctly;
Check that the hour meter operates correctly;
Check that the start control switch operates
correctly: forward and reverse;
Check that the battery monitoring LEDs operate
correctly;
Check that the horn operates correctly;
Check that the seat microswitch operates
correctly;
Check that the reverse buzzer operates correctly.
Attention : if you use
GEL BATTERIES, on the
internal side of the check
batteries remove the
jumper located under
the protection
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 2 of 8
Adjusting the traction system
1. Loosen the lock nut and use the screw that is
indicated to restore correct drive belt tension so that
the spring, when compressed, is about 25-27 mm
long.
2. Adjust correct chain tension using the chain
stretcher:
Unscrew the lock nut;
tighten the M8 screw as necessary, making sure the
traction system does not crawl because this is too
tight;
repeat the operation on the other side, checking they
have the same tension;
tighten the lock nut.
Adjusting the traction levers
1. Remove the metal guard positioned on the footrest
platform.
2. Check if the spring which operates on the friction
discs has a compression of 25 mm. If necessary
unscrew the lock nuts M12 for adjustment of the
spring lengths, which make the operators action on
the levers more homogeneous and moderate (carry
out the adjustment also according to the wear of the
brake discs and the friction discs).
3. Check that the distance between the nut center
spring adjuster and the front part of the machine,
otherwise act on the two upper tie rods.
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 3 of 8
4. Check that, when pushing the traction levers forward
at the end of the slot that they slide in, the
clutches are closed and remain 2-3mm between the
screw head and the washer before the machine starts
to move. Restore a proper position if this is not the
case.
5. Turn the machine on and check that the traction
system lever position and action are the same on the
left side as on the right.
6. Tighten the nuts.
Brake adjustment
1. Check that the traction wheels are locked when the
machine is in rest and when the traction levers are
lightly activated ( lower levers of gear control in
axis with upper levers of gear control that have to
go on the welded plaque and the pressed spring),
the wheels are free.
2. In case of regulation, act on brake levers adjuster,
checking that the distance between the levers handle
and the backrest is about 480 mm.
3. Pay attention that also the traction levers move
towards the operator during the regulation.
Warning : check the position of the traction levers and
the braking power at regular intervals and adjust as
necessary directly on the lock nuts indicated.
48
0
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 4 of 8
Adjusting the Brush Base
1. Lower the brush base.
2. Loosen the two M8 nuts and slide the screws in the
slots so that the brush, when it starts to touch the
floor at the rear, is 4-5 mm higher at the front.
3. Tighten the nuts.
4. Use the specified M8 screws on both sides to adjust
brush height in the lifted position. Note that
tightening the screw increases the distance from the
floor.
5. These screws adjust planarity between brushes and
floor even when working on uneven ground.
6. In order to more easily remove the base (from the
left side of the machine and without brush) first
completely hook up the pedal excluding the gas
spring (you will have maximum pressure on the
floor, 45 Kg., as against the standard 30 Kg.
pressure when the spring is in action).
7. Adjust the bars of the upper microswitches, so
that the brush starts to move when one of the
traction levers is actuated (parallel connection).
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 5 of 8
Testing the Plumbing System
1. Check that the solution filter is clean and in place.
2. Fill the solution tank with water and check for leaks
in the plumbing circuit
3. Check that hoses are sealed, that the solenoid
valve operates properly and that the water cock is
properly adjusted
4. Check that the solution, with the cock open, falls
continuously on the floor and that it falls uniformly
on the brush.
5. Fill the recovery tank and check for leaks.
6. Check the hose seal and the drain plug seal.
7. A connection fitting has been installed on the hose
that carries water to the base. This connection
fitting contains a choke with a hole that can be in
various diameters: Small (colored white, 2.5 mm
diameter); Medium (standard, colored green, 3 mm
diameter); Large (colored black, 3.5 mm diameter).
8. Adjust the bars of the two lower microswitches
that give consent to the solenoid valve so that, when
the traction levers are actuated, they open
simultaneously (they are connected in series) and
water comes out a short time before the machine
starts to move (approximately 4-5 mm before it
reaches the second screw).
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 6 of 8
Testing Suction
1. Check that the filter and the two floating balls are
clean and in efficient working order.
2. Check vacuum seal of the head gaskets.
3. Check that the suction motor operates properly.
4. Check that suction hoses and the squeegee hose are
sealed and properly connected.
Adjusting the squeegee lift system
1. Lift the squeegee and check that the lower part of
the support is 115-120 mm above the floor in order
to simplify squeegee connection and release
procedures.
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 7 of 8
2. If necessari, loose the lock nut of the ring rod to
increase or decrease the height of the squeegee.
Adjusting the Squeegee
1. Check the height of the central wheels and adjust
them as necessary using the M8 self-locking nut,
so that the rubber on the floor has a uniform
inclination on the sides and in the center. Unscrew
to lower the wheel support and screw tighten to lift
it.
2. Use the two knobs to adjust the inclination of the
squeegee:
Unscrew the lock nut;
Adjust each knob so that the rubber along its entire
length is not too crushed against the ground or too
lifted but has an approximate 30° inclination.
Tighten the lock nut.
3. Adjusting squeegee pressure: use the knob,
screwing it to increase pressure and unscrewing it to
decrease pressure.
ADJUSTMENTS AND
INSPECTIONS ENJOY 360
Doc. 10005053
Issued 12/2006
Rev. 00
Page 8 of 8
Brush Reduction Gear Oil
1. Scrubbing base reduction gear: check that the oil in
the reduction gear reaches the transparent oil level
plug (it must not pass this level). Use Shell Omala
460 (oil quantity 0.35 Kg.). Top up through the
upper plug.
Operational testing of the machine
1. Check the efficiency of the traction levers;
2. Check the efficiency of the base;
3. Check the efficiency of the brush motor;
4. Check the efficiency of the solenoid valve;
5. Check the efficiency of the squeegee;
6. Check the efficiency of the suction motor;
7. Check the efficiency of braking when released and emergency;
8. Check the state of the batteries, terminals and cables;
9. Check the efficiency of the horn and the reverse motion buzzer.
Operational tests of the machine
1. Fill the tanks with water and check for leaks.
2. Check the plumbing system for leaks and that water drops uniformly on the brush.
3. Adjust squeegee wheels and inclination and perform an operating test.
4. Adjust the inclination of the base and perform an operating test.
5. Check braking efficiency when released and during emergencies: brake at maximum speed and check
that the wheels lock simultaneously.
6. Check that the machine stops in 115-120 cm when the traction levers are released and it is
operating at maximum speed and with the tank full. If this is not the case then check
adjustment of the brake tie-rods and the traction levers.
7. Check that the seat microswitch operates properly.
8. Check forward, reverse, acceleration and braking operations..
Final Testing
Check all functions: washing, drying, forward gear, reverse motion and braking.
Table des matières
Autres manuels Fimap Machine de plancher
Fimap
Fimap FM1500 S Manuel utilisateur
Fimap
Fimap FS50 B Manuel utilisateur
Fimap
Fimap Magna 1300 Manuel utilisateur
Fimap
Fimap MR60 B Manuel utilisateur
Fimap
Fimap FM43 F Manuel utilisateur
Fimap
Fimap MMg base Instructions d'installation
Fimap
Fimap FS700 H Manuel utilisateur
Fimap
Fimap MR60 Manuel utilisateur
Fimap
Fimap MAGNA PLUS Manuel utilisateur
Fimap
Fimap Minny 420 Instructions d'installation
Fimap
Fimap 1500 S-V Manuel utilisateur
Fimap
Fimap Mx Series Manuel utilisateur
Fimap
Fimap MAGNA 85 BS Guide de référence
Fimap
Fimap FSR B Manuel utilisateur
Fimap
Fimap IMx Manuel d'instructions
Fimap
Fimap BMg Sanitizer Manuel utilisateur
Fimap
Fimap FM33 Manuel utilisateur
Fimap
Fimap FS80 B Manuel utilisateur
Fimap
Fimap GAMMA 66 Manuel utilisateur
Fimap
Fimap GENIE E Manuel utilisateur
Manuels Machine de plancher populaires d'autres marques
Nilfisk-Advance
Nilfisk-Advance Advance SC370 17B Manuel utilisateur
Numatic
Numatic ET 4045 Manuel utilisateur
HAWK ENTERPRISES
HAWK ENTERPRISES HP1513-180BRUTE Manuel utilisateur
Mytee
Mytee 8070 Mytee-Lite Manuel utilisateur
Kärcher
Kärcher B 140 R Manuel utilisateur
Triple S
Triple S Ace 26T1 Manuel utilisateur
