FilterWater FW-2000 Manuel utilisateur
1 | P a g e
MODEL FW-2000
OPERATION
MANUAL
2 | P a g e
Table of Contents
Introduction…….……………………………………………………………………………………..pg.3
Receiving………….…………………………………………………………………………………….pg.4
Description Model H2O-
2000…………….……………………………………………………………...pg.5
Operation……………………………….……………………………………………………………pg.6,7
Drain Container Operation……………………………………………………………….……p.g.8
Cup Dispenser Operation……………………………………………………………………….p.g.9
Positioning the Cooler………………….……………………………………………………….pg.10
Water Cooler Connections…………….………………………………………………........pg.11
Feed Water Connection……………….……………………………………………………….pg.12
Drain Connection……………………….…………………………………………………………pg.13
EZ Connections………………………….………………………………………………………….pg.14
Start Up Flush……………………………………………………………………………............pg.15
Tank Flush…………………………………………………………………………………………….pg.16
Cleaning and Maintenance…………….…………………………………………………….pg.17
Sanitization …………………………………………………………………………………........p.g.18
Filter Replacement………………………….……………………………………………….…..pg.19
Reverse Osmosis Membrane Replacement.…………………………………….……pg.20
Troubleshooting……………………………………….………………………………………....pg.21
Specifications………………………………………….………………………………………..….pg.22
Warranty……………………………………………………….……………………………………..pg.22
List of Figures
Figure 1. Assembly Drawing, Model H2O-
2000………………...….…………………………….pg.5
Figure 2. Faucet Operation…………………………….….………..………………………….pg.6
Figure 3. Hot/Cold Power On/Off Switch.……….….……………..……………………pg.6
Figure 4. Water Cooler Connections………………...…………………………………..pg.11
Figure 5. Drain Connections for “RO” Models……………………………….……...pg.13
Figure 6. Filter Configuration Model “F”……………………………………………….pg.15
Figure 7. Back View of Coolers………………………….…………………………………..pg.16
Figure 8. RO Membrane Installation………………….………………………………….pg.20
3 | P a g e
Introduction
Congratulations on your purchase of our revolutionary Bottle-less Water
Cooler! Our coolers are all designed to replace the conventional 5 gallon
water bottle while eliminating the hassles of deliveries, lifting bottles
and eliminating plastic bottles from landfills. Our coolers are designed
to produce pure great tasting water for the whole family that is clean
and safe to drink.
Our coolers are connected to your city or well water supply to efficiently
filter out tastes and odor, and to remove microscopic contaminants by
using reverse osmosis purification technology. We manufacture a wide
range of models to fit any home or office application.
The H2O-2000 Model has 3 temperature faucets; cold water is chilled
around 44ºF, hot water is heated at 180ºF and ambient.
All International H2O models are manufactured and marked as “RO” or
“F” assemblies. The “RO” assembly utilizes CSM Reverse Osmosis water
purification technology which produces pure safe water from city or
well water. The “RO” assembly is comprised of a 5-micron sediment
filter, a carbon (GAC) 10-micron filter, CSM RO membrane and a post
carbon filter to improve taste. The “RO” filter assembly requires a drain
line connection to be installed which removes rejected water to the
sewer.
The “F” assembly is comprised of sediment and carbon filter system, but
not the RO membrane; therefore, it does not require a drain line
connection.
4 | P a g e
CAUTION: The filter version “F” must be used only with softened
water or water that has less than 3.5-grains of hardness to prevent
scaling and premature burnout of the heating elements.
Receiving the Cooler
Unpacking
International H2O products are shipped completely assembled and
ready to operate. Remove the top of the box and slide the water cooler
out and save the box and packing materials.
Inspection
Inspect the cooler for shipping damage. Look at the exterior panels to
see if they have been dented or damaged. Check the dispensing spigots
in the front. Open the bottom panel to assure that the filter system is
intact. Look at the back of the cooler to see if the compressor is secure
and has not broken from the mounting. Inspect filter system to see that
nothing is damaged or dislodged from shipping.
Description Model H2O-2000
The H2O-2000 Model provides water at 3 different temperatures,
dispensed from three spigots, “hot”, “cold” and ambient. The assembly
drawing is shown in Figure 1. Water flows from the filter system into the
ambient tank and the cold water tank simultaneously. The cold tank
then feeds the hot tank which is heated by internal heaters. The level in
the cold water tank is controlled by a float valve mechanism which
controls a 4 way auto-shut off valve on the water feed line to maintain a
5 | P a g e
constant level of filtered water. Both models are available with reverse
osmosis (RO) or standard filter (F) versions.
Description Model H2O-2000
6 | P a g e
Figure 1. Assembly Drawing Model H2O-2000
Operation
When installation is complete,
the unit will fill up with water
and shut off when the tanks are
full. Plug the unit in to an outlet
and press the cold/hot faucets
until a steady stream of water
comes out.
Figure 2. Faucet operation
*Make sure the tanks are filled
with water before continuing to
the next step.
Turn on the hot/cold switches
located on the back of the cooler.
Both hot/cold elements will begin
chilling and heating the water
inside the unit. Indicator lights will
also illuminate of the front of the
cooler.
7 | P a g e
Figure 2. Hot and cold power on/off switch
Operation Cont…
8 | P a g e
Drain Container Operation
9 | P a g e
Cup Dispenser Operation
10 | P a g e
Positioning the Cooler
1) It is not recommended to install this cooler in an area were water
may cause severe or costly damage.
Table des matières
Autres manuels FilterWater Distributeur d'eau
