Fife SBPC-21-EN Manuel utilisateur

FIFE CORPORATION

222 W. Memorial Road, Oklahoma City, OK 73126-0508

Post Office Box 26508, Oklahoma City, OK 73114-2317

Phone: 405.755.1600 / 800.639.3433 / Fax: 405.755.8425

www.fife.com / E-mail: fif[email protected]

SBPC-21-EN

FifeNet To Ethernet Gateway

Customer Instruction Manual

Modbus/TCP Ethernet

07-02-2004 Figure Sheet 1-849-C

SBPC-21-EN CUSTOMER INSTRUCTION MANUAL

• • • • • •

the prior written consent of Fife Corporation.

The information given in this Instruction Manual is subject to change without notice.

We have compiled this Instruction Manual with the greatest possible care and attention. However, the

possibility of error cannot be completely excluded. Fife Corporation accepts no legal liability for

incorrect information given and the consequences arising there from.

MS DOS is a trademark of Microsoft Corporation.

07-02-2004 Figure Sheet 1-849-C Page i

07-02-2004 Figure Sheet 1-849-C Page ii

SBPC-21-EN CUSTOMER INSTRUCTION MANUAL

TABLE OF CONTENTS

• • • • • •

INTRODUCTION ......................................................................................................................................... 1

PRODUCER/CONSUMER MODEL .................................................................................................................1

FIFENET....................................................................................................................................................1

SBPC-21-EN SWITCH/JUMPER CONFIGURATION .......................................................................................2

SBPC-21-EN EXTERNAL CONNECTIONS/INDICATORS ................................................................................3

SBPC-21-EN NETWORK STATUS ..............................................................................................................4

SBPC-21-EN ERROR CODES ....................................................................................................................5

TCP/IP FEATURES ....................................................................................................................................6

SBPC-21-EN NETWORK CONFIGURATION .................................................................................................6

IP ADDRESS..............................................................................................................................................6

SUBNET MASK...........................................................................................................................................6

SPECIAL CASE IP ADDRESSES ...................................................................................................................6

CONFIGURING IP ADDRESS........................................................................................................................7

USING CONFIGURATION SWITCH ................................................................................................................7

USING DHCP/BOOTP................................................................................................................................7

USING A PREDEFINED CONFIGURATION ......................................................................................................7

USING ADDRESS RESOLUTION PROTOCOL (ARP).......................................................................................8

FILE SYSTEM.............................................................................................................................................9

CONFIGURATION FILE ETHCFG.CFG ............................................................................................................9

TELNET SUPPORT .................................................................................................................................10

MODBUS TCP .........................................................................................................................................11

FIFENET THEORY ................................................................................................................................... 13

FIFENET TIME SLICES..............................................................................................................................13

MULTIPLEXED TIME SLICES ......................................................................................................................13

FIFENET MASTER ....................................................................................................................................14

SBPC-21-EN DATA FLOW.......................................................................................................................15

CONFIGURATIONS................................................................................................................................... 17

HARDWARE CONFIGURATION – SINGLE CDP-01.......................................................................................17

HARDWARE CONFIGURATION – MULTIPLE CDP-01’S................................................................................18

SOFTWARE CONFIGURATION....................................................................................................................18

COMMUNICATION MAPPING..................................................................................................................... 19

MODBUS TO FIFENET DATA .....................................................................................................................19

FIFENET TO MODBUS DATA .....................................................................................................................20

CONTROL INFORMATION ......................................................................................................................... 23

CDP-01 CONTROL MATRIX......................................................................................................................23

EXTERNAL LOCK......................................................................................................................................23

SINGLE-DRIVE CDP-01 ...........................................................................................................................23

DUAL-DRIVE CDP-01 ..............................................................................................................................24

TRIPLE-DRIVE CDP-01............................................................................................................................25

STATUS DATA BLOCK ..............................................................................................................................26

07-02-2004 Figure Sheet 1-849-C Page iii

SPECIAL CONTROL OF FIFENET DEVICES.................................................................................................33

CDP-01 KEY CODE DATA PATH...............................................................................................................33

CDP-01 KEY CODES ...............................................................................................................................34

SIMULATING DUAL-KEY PRESSES.............................................................................................................34

CDP-01 LED PANEL DATA......................................................................................................................35

INDEX......................................................................................................................................................37

07-02-2004 Figure Sheet 1-849-C Page iv

SBPC-21-EN CUSTOMER INSTRUCTION MANUAL

INTRODUCTION

• • • • • •

The Fife SBPC-21-EN (Serial Bus Protocol Converter) provides a gateway between Fife’s proprietary

FifeNet network and an Ethernet network. The SBPC-21-EN uses the standard RJ-45 connector and

conforms to the Modicon Open Modbus/TCP Specification, Release 1.0 (March 29, 1999). As shown

in the diagram below, the SBPC-21-EN connects to both FifeNet and Ethernet.

Figure 1-1: SBPC-21-EN Network Connection

The SBPC-21-EN

connects to both

FifeNet and Ethernet

providing translation

between the two

networks.

Ethernet Hub

Customer

Ethernet

FifeNet

Producer/Consumer Model

The Producer/Consumer model allows the exchange of information between a sending device

(“producer”) and many receiving devices (“consumer”) without requiring the same date to be sent

multiple times to different destinations. The producer sends the data once and each consumer on the

network receives the data at the same time. The data can be used (consumed) or ignored by each

receiving device independently. FifeNet uses the Producer/Consumer Model.

FifeNet

FifeNet’s deployment of the Producer/Consumer Model allows data sent by a single device to be

received simultaneously by multiple devices on the same network. Each receiving device can choose

to use (consume) the information or ignore it as needs dictate. FifeNet is based on a fixed time slicing

architecture where transmitting devices send data in fixed, predetermined time intervals.

07-02-2004 Figure Sheet 1-849-C Page 1

SBPC-21-EN Switch/Jumper Configuration

Since the SBPC-21-EN participates in two networks at the same time, it must have two network

addresses (a FifeNet address and an Ethernet IP address). The FifeNet address is set via the FifeNet

serial port that is common with many FifeNet peripherals. The Ethernet IP address is programmable

by dipswitches or via the Ethernet connection. See the dipswitch description and IP address

configuration setup shown below for more information. If the SBPC-21-EN is installed as the end point

in a FifeNet network, all four jumpers described below should be installed.

Figure 1-2: SBPC-21-EN Top View

These jumpers should be installed if the

SBPC-21-EN is at the end of a FifeNet

network. They provide network

termination. The other two jumpers

should always be installed as they

select half-duplex FifeNet

communication.

Not Terminated Terminated

The 7-segment LED is

used to display errors or

exceptions. During normal

operation, the display will

continuously “cycle” the

outer segments.

The Ethernet IP address

configuration switches. See the

following page for description of

these switches.

07-02-2004 Figure Sheet 1-849-C Page 2

SBPC-21-EN External Connections/Indicators

SBPC-21-EN mounting considerations are simplified as all connections to the SBPC-21-EN are on the

same side of the box.

Figure 1-3: SBPC-21-EN Side View

Connection to FifeNet is

accomplished using the

standard FifeNet connector.

Configuration is also

downloaded to the device

using this connection.

Device and network status

LED’s. These indicators

provide feedback for

network troubleshooting.

Connection to Ethernet is

accomplished using the

standard RJ-45 connector.

Switch Value = 1-255

The IP address configuration switches can be used to configure

the IP address in an intranet network. The first three values of

the IP address are fixed at 192.168.0 and the dip switch value

represents the binary value of the last digit of the IP address.

The subnet mask is 255.255.255.0 and the default Gateway is

0.0.0.0.

In the switch example shown above, the IP address is set to

192.168.0.20.

Switch

1 2 3 4 5 6 7 8

OFF OFF OFF ON OFF ON OFF OFF

Switch Value = 0

Set the switches to zero as shown below to use a

DHCP/BootP server if present or use the internally stored IP

address. If a DHCP/BootP server is not present, the stored IP

address will be used. See the section SBPC-21-EN Network

Configuration for details about how to store an IP address.

Switch

1 2 3 4 5 6 7 8

OFF OFF OFF OFF OFF OFF OFF OFF

07-02-2004 Figure Sheet 1-849-C Page 3

SBPC-21-EN Network Status

The SBPC-21-EN network status is determined by interpretation of the external LED status as

described in the table below.

Figure 1-4: SBPC-21-EN LED Indicators

Table 1-1

LINK LED

LED State Meaning

Off Ethernet network not detected.

Solid Green The SBPC-21-EN is connected to an Ethernet network.

MODULE STATUS

LED State Meaning

Off SBPC-21-EN initializing.

Flashing Green The Ethernet IP address is NOT configured by the dip switches.

Flashing Red (1 Hz) Invalid MAC ID (Internal error).

Flashing Red (2 Hz) Failed to load Ethernet configuration from internal FLASH.

Flashing Red (4 Hz) Internal error.

Solid Red Duplicate IP address detected.

NETWORK STATUS

LED State Meaning

Off No Modbus/TCP connections are established.

Flashing Green

This LED flashes green to indicate the number of Modbus/TCP connections that

are currently active to the SBPC-21-EN. The number of flashes is equal to the

number of connections.

ACTIVITY LED

LED State Meaning

N/A The ACTIVITY LED flashes green when a packet is received or transmitted.

07-02-2004 Figure Sheet 1-849-C Page 4

Table des matières

Autres manuels Fife Porte

Fife

Fife SBPC-21-EN/IP Manuel utilisateur

Fife

Fife SBPC-21-PB PROFIBUS DP Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur