Fieldpiece ACH Manuel utilisateur

300AC Current Clamp

Accessory Head:

Model ACH

Fieldpiece

OPERATOR'S MANUA

Quick start...Quick start...

Quick start...

Clamp the jaws around a single

conductor, set the meter to the

lowest mVAC range and read

amps up to "199.9".

Introduction...Introduction...

Introduction...

The Fieldpiece Model ACH

converts AC current to a voltage

easily measured by most DMM's

by just clamping the jaws around a

current carrying conductor.

The model ACH1 current

clamp converts AC amps to

voltage at a rate of 1 amp to 1mV

(1000 to 1).

The ACH Clamp Head was

designed to be snapped directly

onto the Fieldpiece HS Series

DMM or to be used with the

Fieldpiece HB70 series or any

DMM that has the industry

standard "Fluke" style input jacks

using the Deluxe Test Leads

(ADL2).

When snapped onto the

Fieldpiece HS Series Stick Style

DMM the pair make a convenient

one piece digital clamp meter that

reads current directly, without

requiring the user to perform

mental calculations or move the

decimal point.

The ACH also snaps onto the

EHDL1 electronic handle to make

a convenient stand alone current

clamp meter.

For your safety...For your safety...

For your safety...

Do not attempt to measure any

circuit in which the circuit-to-

ground voltage exceeds 1000V

rms.

Measurement of AC power

sources with inductive loads or AC

power sources during electrical

storms may result in extremely

high-voltage, high-energy transients

that could damage the meter and

consequently expose the user to a

dangerous shock hazard.

Inspect the test leads for

damage to the insulation or exposed

metal. Replace or do not use if

suspect.

When disconnecting from a

voltage measurement, disconnect

the “hot” lead first, then the

common.

Discharge capacitors prior to

making resistance or capacitance

measurements.

Work with others.

Use one hand.Hands, shoes, and

floor must be dry when taking

measurements.

Avoid use of the current

converter under humid or damp

conditions which could affect the

dielectric withstanding voltage of

the clamp.

Specifications:Specifications:

Specifications:

Current range: 1A to 300A rms

Conversion rate: 1AAC to

1mVAC.

Frequency: 40Hz to 500Hz

Operating temp.: -15 oF to 130 oF

Accuracy (±reading±least

significantdigits,72oC±8oF,

Clamp head only--add to DMM

accuracy for total accuracy)

50Hz to 60Hz ±1.5% + 1

30Hz to 500Hz ±4% + 1

Temperature coefficient: less than

0.010% per oC

Circuit-to-ground voltage:

1000Vrms max.

Maximum conductor size: 0.91

inches (23mm)

Dimensions: 1.14 inches x 2.84

inches x 4.17 inches

Operating instructions:Operating instructions:

Operating instructions:

1. Connect the ACH Clamp Head

to digital multimeter V- W and

COM terminals. (Polarity is

not important.)

2. Set the multimeter to mVAC

range.

3. Snap the jaws of the current

converter around one of the

current-carrying conductors.

Make sure the jaws are tightly

clamped.

4. Directly read the current value

(in amperes) indicated on the

display (multiply by 1000 if

using the 2V range).

5. If meter dispalays overload,

change range to next highest

(2000mVAC or 2VAC. For

2VAC range, multiply reading

by 1000.)

Maintenance:Maintenance:

Maintenance:

For the Clamp Head to operate

properly, the magnetic joint

surfaces should be maintained free

of dust, dirt, or residues of wire

insulation.

Clean the Clamp Head using a

mild detergent in water. Other

solvents may damage the plastic or

reduce the effectiveness of the

insulation. Dry the instrument

thoroughly before use.

Service:Service:

Service:

There are no user serviceable

parts inside.

The warranty statement for

Fieldpiece ACH Clamp Head in

the back of this manual. Read it

carefully before requesting

warranty service. Any ACH

Clamp Head claimed to be

defective should be returned to

Fieldpiece Instruments for

warranty service.

Warranty service will typically

be made within 24 hours after

receipt of defective unit. Any non-

working out-of-warranty product

may be sent to Fieldpiece

Instrument for service. Send the

ACH Clamp Head along with a

check or money order for $15.00

Fieldpiece Instruments

580 West Central Ave. Suite A

Brea, CA 92821

Your repaired or replaced

Clamp Head will be returned to

you with a 6 month warranty.

WARRANTY:WARRANTY:

WARRANTY:

The ACH is warranted to the

original purchaser against defects in

material or workmanship for a

period of two (2) years from the

date of purchase. During the

warranty period, Fieldpiece

Instrument will, at its option,

replace or repair the defective unit.

This warranty does not apply to

defects resulting from abuse,

neglect, accident, unauthorized

repair, alteration, or unreasonable

use of the instrument. Any implied

warranty arising out of the sale of

Fieldpiece's products including but

not limited to implied warranties of

merchantibility, and fitness for

purpose, are limited to the above.

Fieldpiece shall not be liable for

incidental or consiquential damages.

Table des matières

Autres manuels Fieldpiece Instrument de mesure

Fieldpiece

Fieldpiece CAT85K2 Manuel utilisateur

Fieldpiece

Fieldpiece CAT45K2 Manuel utilisateur

Fieldpiece

Fieldpiece SCM4 Manuel utilisateur

Fieldpiece

Fieldpiece CAT85 Manuel utilisateur

Fieldpiece

Fieldpiece ATA1 Manuel utilisateur

Fieldpiece

Fieldpiece ACM3 Manuel utilisateur

Fieldpiece

Fieldpiece JL3PR Manuel utilisateur

Fieldpiece

Fieldpiece SMAN SM480VINT Manuel utilisateur

Fieldpiece

Fieldpiece SMAN SM380VINT Manuel utilisateur

Fieldpiece

Fieldpiece HS35 Manuel utilisateur

Fieldpiece

Fieldpiece SC260 Manuel utilisateur

Fieldpiece

Fieldpiece HG3 Manuel utilisateur

Fieldpiece

Fieldpiece SC460 Manuel utilisateur

Fieldpiece

Fieldpiece ATWB1 Manuel utilisateur

Fieldpiece

Fieldpiece CAT45 Manuel utilisateur

Fieldpiece

Fieldpiece SC660 Manuel utilisateur

Fieldpiece

Fieldpiece SOX3 Manuel utilisateur

Fieldpiece

Fieldpiece ASP2 Manuel utilisateur

Fieldpiece

Fieldpiece HG3 Manuel utilisateur

Fieldpiece

Fieldpiece SC54 Manuel utilisateur

Fieldpiece

Fieldpiece STA2 Manuel utilisateur

Fieldpiece

Fieldpiece EH4W Manuel utilisateur

Fieldpiece

Fieldpiece SC640 Manuel utilisateur

Fieldpiece

Fieldpiece JL3RH Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur