Fieldpiece SC660 Manuel utilisateur

Fieldpiece

Wireless

Clamp

Meter

OPERATOR'S

MANUAL

Model SC660

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Description

The SC660 is the top of the line clamp meter with

wireless functionality for the HVACR professional.

Receive wireless measurements from Fieldpiece

accessory heads and wireless transmitters from

anywhere on the jobsite. For instance, receive

an indoor delta T temperature measurement

wirelessly from a Fieldpiece transmitter while

you work at the condenser. Send your electrical

measurements to the Job Link™ mobile app via the

Fieldpiece JL2 Transmitter. (See Wireless section for

more details).

Hang your SC660 clamp meter to any metallic

surface with the heavy-duty magnet and when the

job is done, snap your test leads in the back case for

tidy and convenient storage. See both voltage and

amperage readings at the same time on the large

dual display, even in low light conditions using the

bright blue backlight.

Easily see your amperage readings no matter

how you clamp around a wire with the swivel head

AAC clamp.

Verify the order of 3-phase voltage lines with

just two leads. Capture L1-L2 and L1-L3 to check

that motor lines are correctly installed with Phase

Rotation test.

Measure the delta T across the evaporator with

dual Type K temperature ports on the SC660.

Take more accurate VAC and AAC readings on

variable frequency drives with True RMS sensing

technology. Measure the starting amp draw of a

compressor with Inrush current mode.

Illuminate the way with a powerful LED built into

the clamp jaw. Easily see your measurements with

the bright blue backlight on the display, and know

what parameters you are testing with the backlit

illuminated dial.

Take measurements more safely with one hand

using the single test lead holder. Test leads come

with removable gold plated tips to connect with

Fieldpiece accessory heads.

The SC660 clamp meter is built to withstand the

rigors of HVACR eld work with high impact plastic

and a display you can read in very hot or very cold

environments.

What’s Included

•SC660 Wireless Clamp Meter

•ADLS2 Deluxe Test Leads Kit

•ASA2 Alligator Clips

•2 ATB1 Type K Thermocouples

•2 Velcro Straps

•9V Alkaline Battery (Not installed)

•ANC7 Protective Padded Case

•Operator’s Manual

Quick Start

1. For electrical testing, connect test leads to black

"COM" and red "+" jacks.

2. Rotate the dial to your desired measurement.

3. Connect to test points and read measurement.

4. For temperature testing, remove test leads, slide

TEMP switch to the right and connect Type K

thermocouples.

Certiﬁcations

UL 61010-1, Third Edition

EN61010-1, EN61010-2-032

EN61010-2-033, EMC EN61326-1

FCC ID: VEARF915A

C-Tick (N22675)

WEEE

CATIII 600V, class II and pollution degree 2 indoor

use comply with CE, RoHS compliant.

CATIII is designated for measurements performed

in the building installation.

Speciﬁcations

Display: 10000 count dual display

Backlight: 5 minute duration with auto-o. Blue color

Overrange: (OL) or (-OL) is displayed

Measurement rate: 3.3 times per second, nominal

Zero: Automatic

Operating environment: 32°F to 122°F (0°C to 50°C) at <70%RH

Storage temperature: -4°F to 140°F (-20°C to 60°C), 0 to 80%RH (with

battery removed)

Accuracy: Stated accuracy @ 73°F±9°F (23°C±5°C), <75%RH

Temperature coecient: 0.1 x (specied accuracy) per °C [0°C to 19°C

(32°F to 66°F), 28°C to 50° C (82°F to 122°F)]

APO (Auto Power O): Approx. 30 minutes

Power: Single standard 9-volt battery, NEDA 1604, JIS 006P, IEC 6F22

Battery life: 100 hours typical alkaline

Low battery indication: Battery icon blinks and "batt" is displayed

when the battery voltage drops below the operating level

Dimensions: 287.5mm(H) x 79.5mm(W) x 50.0mm(D)

Weight: Approx. 450g including battery

Altitude: Up to 6562 ft (2000m)

Overload protection: 600VDC or 600VAC rms unless otherwise stated

Test leads: Use UL listed test leads that comply to UL61010-031 rated

CATIII 600V or above. Included test leads are gold-plated and have

removable safety caps.

Please operate the instrument following all instructions of

the operator's manual to avoid impairing the safety of

the product.

Buttons

Illuminatebacklight.Pressfor1secondto

zero Amps DC.

Activate Inrush AAC capture mode.

Press for 1 second to connect to

compatible Fieldpiece wireless tools.

ActivateandcyclethroughHold,Maximum,

minimum,and real-timemeasurements.

Press for 1 second to clear and exit.

Press to log measurements in Job Link™.

Deactivate autoranging and move the

decimal point as desired.

Cycle through displayed values on

applicable switch positions. Press for 1

second to toggle °F and °C.

Measurements Dial

The SC660 is loaded with the measurement

parameters essential for HVACR professionals.

Select the parameter on the dial you want to

measure with the rotating selector switch.

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO ADC

°F °C

TEMP

CAT III

600V

COM

INRUSH

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO ADC

°F °C

TEMP

CAT III

600V

COM

INRUSH

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

Display Icons

Battery Life Monitor

Auto Power O Enabled

High Voltage Warning (>30VAC/VDC)

Manual Ranging

Data Hold

Maximum

Minimum

Inrush AAC

Wireless Enabled (searching if ashing)

Wireless Signal Strength Bars

Temperature Inputs

Delta T

Fahrenheit

Celsius

Continuity Test

Diode Test

Frequency (Hertz)

Duty Cycle (percentage)

Resistance Test (Ohms)

Capacitance Test (farads)

Microamps DC

Nano Unit (10−9, one billionth)

Micro Unit (10−6, one millionth)

Milli Unit (10−3, one thousandth)

Kilo Unit (103, one thousand)

Mega Unit (106, one million)

Alternating Current

Direct Current

Easy to Read Display

Easily see your measurements on the large dual

display. You’ll never miss a reading no matter the

lighting with the bright blue backlight to illuminate

the way.

1110

Test Parameters

Volts AC (VAC) True RMS (50-500Hz)

Test power lines (120, 220, 480VAC), test 24VAC going to controls, and

test for transformer failure.

Ranges: 1000mV, 10V, 100V, 600V Resolution: 0.1mV

Accuracy: ±(1.2% + 10) 1000mV, 10, 100V range

±(1.5% + 10) 600V range

Minimum Input Voltage Range: >20 digits

Crest factor: ≤ 3

Audio/Visual Hi-V indicator: >30VAC/VDC

Input impedance: 5MΩ

Overload Protection: 600VDC or 600VAC rms

Volts DC (VDC)

Select VDC and measure DC voltages on circuit boards on more

advanced HVACR systems and logic control boards. In ADC/VDC dial

position, VDC is shown on lower display. Press SELECT button to show ADC

on the top display at the same time.

Ranges: 1000mV, 10V, 100V, 600V Resolution: 0.1mV

Accuracy: ±(0.5% + 5)

Input impedance: 5MΩ

Overload Protection: 600VDC or 600VAC rms

Non Contact Voltage (NCV)

Use NCV to check 24VAC from a thermostat or live voltage up to 600VAC.

Always test a known live source before using. A segment graph and RED

LED will display the presence of voltage. An audible beep increases from

intermittent to continuous as intensity of eld (EF) increases.

AC Voltage Detection Range: 24VAC to 600VAC (50-60Hz)

TRUE RMS AUTO OFF

TYPEK 30VMAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZEROA

°F°C

COM

INRUSH

1312

Inrush AAC Current

Inrush mode captures the starting amp draw of a motor. Starting amp

draw can assist in diagnosing a motor before it fails.

Activate Inrush mode

1 Rotate selector switch to VAC/AAC/Hz orVAC/400AAC/Hz

2 Press SELECT once to show AAC on upper display. Press INRUSH on the

right side of meter to activate.

3 Clamp meter around the motor’s start wire.Turn motor on. The

starting amp draw will hold on the upper display.

4 Press INRUSH to reset the test. Press INRUSH for 2 seconds to exit

Inrush mode.

Inrush measurement period: 100-milliseconds

Minimum input: >2A on AAC range; >20A on 400A range

Note: AAC or Hz through the clamp and VAC through the test leads

can be measured simultaneously. However, if only AAC, Frequency

(Hz), or Inrush AAC is measured through the clamp, test leads and

thermocouples must be unplugged from the meter.

Amps AC (AAC) True RMS (50-60Hz)

Test any isolated power line. Press SELECT once on VAC/AAC/Hz

position. Read AAC in upper display and VAC on the lower display at the

same time. For AAC measurements <100AAC, select AAC switch position

and for measurements >100AAC, select the 400AAC switch position.

Range: 100A, 400A Resolution: 0.01A Crest factor: ≤ 3

Accuracy: ±(2.5% + 15) 100A, ±(2.0% + 10) 400A

Minimum Input Current Range: >20 digits

Overload Protection: 400AAC Jaw Opening: 1.2in (30 mm)

Frequency (Hz) Through Clamp

Measure Hz on variable frequency drive motors. Turn dial to either VAC/

AAC/Hz and press SELECT twice. Hz will show in upper display and VAC on

the lower display at the same time.

Range: 10Hz to 400Hz Resolution: 0.1Hz

Accuracy: ±(0.1% + 5)

Minimum current range: >10AAC (10 to 100Hz); >25AAC (100 to

400Hz) on AAC switch; >50AAC (10 to 400Hz) on 400AAC switch.

Overload Protection: 400AAC

Amps DC (ADC)

Measure ADC through the clamp jaw. Press

TRUE RMS AUTO OFF

TYPE K 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZERO A

°F °C

TEMP

CAT III

600V

COM

INRUSH

for 1 second to zero

the ADC value in the top display.

Ranges: 100A, 400A Resolution: 0.01A Jaw Opening: 1.2in (30 mm)

Accuracy: ±(2.5% + 15) 100A, ±(2.0% + 10) 400A

Overload Protection: 400ADC

TRUE RMS AUTOOFF

TYPEK 30VMAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZEROADC

°F°C

COM

INRUSH

TRUE RMS AUTO OFF

TYPEK 30V MAX

L1 L2

Sync

OFF

Range Select H/M/m

SC660

ZEROA

°F°C

COM

INRUSH

1514

MicroAmps DC (µADC)

Microamps for ame rectier diode test on a heater control. Connect

leads between ame sensor probe and control module and turn heating

unit on to read µA measurement.When the ame is on, there should be a

measurable µADC signal, typically under 10µADC. Compare measurement

to manufacturer’s specication to determine if replacement is necessary.

Ranges: 1000µA Resolution: 0.1µA

Accuracy: ±(1.0% + 5) Volts burden: 5V

Overload Protection: 600VDC or 600VAC rms

Frequency (Hz) Through Leads

Check incoming voltages to ensure they are cycling at 60Hz. For

frequency measurements onVFD equipment, use the amp clamp.

Ranges: 100Hz, 1kHz, 10kHz, 100kHz, 1MHz Resolution: 0.01Hz

Accuracy: ±(0.1% + 5) Sensitivity: 10Hz to 1MHz: >3.5Vrms

Minimum PW: >1µs Duty Cycle Limits: >30% and <70%

Duty Cycle (%)

Duty cycle shows the % OnTime of a 5V logic signal square wave.

Ranges: 5%-95% (40Hz to 1kHz), 10%-90% (1kHz to 10kHz), 20%-80%

(10kHz to 20kHz)

Accuracy (5V logic): ±(2% + 10) Resolution: 0.1%

Pulse Width: >10µs

Overload Protection: 600VDC or 600VAC rms

Capacitance (MFD)

Set to MFD to test motor start and run capacitors. Capacitors are one

of the most failure prone components in a HVACR system. Disconnect

from power and resistors between terminals. Discharge capacitor before

testing. If dIS.C is displayed, the capacitor needs to be fully discharged to

test.

Ranges: 10nF, 100nF, 1000nF, 10µF, 100µF, 1000µF, 10mF

Accuracy: ±(3% + 15) 10nF, ±(3% + 5) 100nF to 1000µF, ±(5% + 5) 10mF

Resolution: 0.01nF Overload Protection: 600VDC or 600VAC rms Discharge Cap First!

1716

Resistance (Ω)

Used for“ohming out”a compressor. A 0.01Ω resolution is useful to

test the resistance between the terminal poles because the values are

typically very low.

Ranges: 100Ω, 1000Ω, 10kΩ, 100kΩ, 1000kΩ, 10MΩ, 50MΩ

Resolution: 0.01Ω

Accuracy: ±(1.0% + 15) 100Ω, ±(1.0% + 5) 1000Ω to 100kΩ, ±(1.5%

+ 5) 1000kΩ, ±(3.0% + 5) 10MΩ to 50MΩ

Open circuit volts: -1.1VDC typical, -3.2VDC (100Ω range)

Overload Protection: 600VDC or 600VAC rms

Continuity (

NCV

VAC VDC

AAC

°C

°F

SC56

AUTO OFFTRUE RMS

CAT III

600V

TEMP

K-TYPE

30V

MAX

SEL

HOLD

INRUSH

)

Use the continuity feature to test if a circuit is open or closed. Use this

feature to check isolated fuses as well. A steady“beep”and green LED

indicate you have continuity. Press SELECT once to enter Continuity mode.

Range: 100Ω Resolution: 0.01Ω Response time: 100ms

Audible beep: <30Ω

Overload Protection: 600VDC or 600VAC rms

Diode Test (

NCV

AC VDC

AAC

°C

°F

SC56

AUTO OFFTRUE RMS

CAT III

600V

TEMP

K-TYPE

30V

MAX

SEL

HOLD

INRUSH

)

Test diodes for proper forward and reversed-biased functions. Press

SELECT twice to enter Diode mode.

Test current: 0.8mA (Approx.) Accuracy: ±(1.5% + 5)

Open circuit volts: 3.2VDC typical Audible beep: <0.05V

Visual Indicator: Green LED

Overload Protection: 600VDC or 600VAC rms

1918

Dual Temperature (T1, T2, T1-T2)

Plug anyType K thermocouple directly into the meter to measure

temperature. Test for proper airow across the evaporator coil by

measuring delta T with the dual temperature inputs.

Cold junction is located inside the meter and allows for accurate

measurements even in rapidly changing ambient temperatures (going

from rooftop to freezer). No adapter is required.

By default,T1 will show on top display andT2 on bottom display. Press

SELECT button once to displayT1 on top and T1-T2 on the bottom. Press

SELECT button again to displayT2 on top and T1-T2 on the bottom.

Range: -58°F to 2372°F, (-50°C to 1300°C) Resolution: 0.1°

Accuracy: ±(1°F)* 32°F to 120°F, ±(1°C) 0°C to 49°C

±(1%+2°F) 32°F to 932°F, ±(1%+1°C) 0°C to 500°C

±(2%+6°F) -58°F to 32°F, ±(2%+3°C) -50°C to 0°C

±(2%+6°F) 932°F to 2372°F, ±(2%+3°C) 500°C to 1300°C

Sensor type: Type K thermocouple *After eld calibration

Overload protection: 30 VDC or 30VAC rms

Change Units (°F or °C)

By default, temperature units are set to Fahrenheit (°F). In

Temperature dial position, press SELECT button for 1 second to toggle

between Fahrenheit (°F) and Celsius (°C).

Unplug Leads and Slide

TEMP Switch to the Right

TRUE RMS AUTO OFF

TYPE K30V MAX

TEMP

L1 L2

COM

CAT III

600V

Temperature Calibration

For accuracies of ±1°F, calibrate both

thermocouples to a known temperature. A glass

of stabilized ice water is very close to 32°F (0°C)

and is usually very convenient but any known

temperature can be used. Ideally you should

calibrate to a known temperature closest to the

temperatures you will be testing.

1. Rotate dial to the °F °C, T1-T2

position.

2. Plug one thermocouple to be

calibrated into the T1 Type K jack.

3. Unscrew A and B and remove the

battery cover.

4. Stabilize a large cup of ice water.

Stir the ice with the water until

temperature stays at a stable value.

5. Immerse the T1 thermocouple

probe and let it stabilize.

Keep stirring water to prevent

thermocouple from direct contact

with ice.

6. Use a small screwdriver to adjust

calibrationT1 Temp Cal pot below

the battery as close to 32°F(0°C) as

you would like.

7. Repeat step 2-6 and replace T2 for

T1 for T2 thermocouple.

Note: J1-J2 switch is for factory

calibration purposes only. Do not

switch from J2.

TEMP

CAL

DO NOT SWITCH

FROM J2

Table des matières

Autres manuels Fieldpiece Instrument de mesure

Fieldpiece

Fieldpiece SDMN6 Manuel utilisateur

Fieldpiece

Fieldpiece SC680 Manuel utilisateur

Fieldpiece

Fieldpiece SC55 Manuel utilisateur

Fieldpiece

Fieldpiece SOX3 Manuel utilisateur

Fieldpiece

Fieldpiece HS26 Manuel utilisateur

Fieldpiece

Fieldpiece SRH3 Manuel utilisateur

Fieldpiece

Fieldpiece JL3RH Manuel utilisateur

Fieldpiece

Fieldpiece ATA1 Manuel utilisateur

Fieldpiece

Fieldpiece SC76 Manuel utilisateur

Fieldpiece

Fieldpiece ADMN2 Manuel utilisateur

Fieldpiece

Fieldpiece FPSC680 Manuel utilisateur

Fieldpiece

Fieldpiece AAT3 Manuel utilisateur

Fieldpiece

Fieldpiece HVAC Guide HG1 Manuel utilisateur

Fieldpiece

Fieldpiece HG3 Manuel utilisateur

Fieldpiece

Fieldpiece JL3PR Manuel utilisateur

Fieldpiece

Fieldpiece ASX14 Manuel utilisateur

Fieldpiece

Fieldpiece DDSM1 Manuel utilisateur

Fieldpiece

Fieldpiece SOX3 Manuel utilisateur

Fieldpiece

Fieldpiece SC460 Manuel utilisateur

Fieldpiece

Fieldpiece SC260 Manuel utilisateur

Fieldpiece

Fieldpiece AMN2 Manuel utilisateur

Fieldpiece

Fieldpiece ACM3 Manuel utilisateur

Fieldpiece

Fieldpiece JL3PR Manuel utilisateur

Fieldpiece

Fieldpiece SMG5 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur