Fenix Imvico EPC1200 Series Manuel utilisateur

PC1

IF120

INTE

HER

FACE

Ope

and PT

ation

Version

PRI

R2 Sta

manu

2.1

e Print

IES

EPC1200 SERIES OPERATION MANUAL

2/58

INDEX

1 – INTRODUCTION 4

2 – IMPORTANT NOTES ON EPC1200 THERMAL PRINTER HANDLING ..............................5

2.1-SAFETY PRECAUTIONS.....................................................................................................5

2.2-ABSOLUTE MAXIMUM RATINGS......................................................................................5

2.3-CLEANING PROCEDURE AND PRECAUTIONS ............................................................6

2.4-RECOMMENDATIONS.........................................................................................................6

3 – GENERAL SPECIFICATIONS..............................................................................................7

3.1-PRINTING SPECIFICATIONS.............................................................................................7

3.2-CHARACTER SPECIFICATIONS .......................................................................................7

3.3-PAPER SPECIFICATIONS ..................................................................................................7

3.4-PAPER LOADING..................................................................................................................7

3.5-INTERNAL BUFFER..............................................................................................................8

3.6-ELECTRICAL SPECIFICATIONS .......................................................................................8

3.7-ENVIRONMENTAL CONDITIONS......................................................................................8

4 – INSTALLATION ....................................................................................................................9

4.1-EPC1200 INSTALLATION CONSIDERATIONS...............................................................9

4.2-POWER SUPPLY ................................................................................................................11

4.3-RS-232 SERIAL INTERFACE............................................................................................13

4.3.1- RS-232 Serial interface specifications......................................................... 13

4.3.2- Change between online and offline mode................................................... 13

4.3.3- Serial RS-232 interface pins assignment .................................................... 13

4.3.4- PC serial interface connection..................................................................... 14

4.4-CENTRONICS PARALLEL INTERFACE.........................................................................14

4.4.1- Compatibility mode (Data transmission from host to printer) ...................... 14

4.4.2- Reverse mode (Data transmission from the printer to the host system) ..... 15

4.4.3- Parallel interface pins assignment for each mode....................................... 16

4.4.4- PC parallel interface connection.................................................................. 17

4.5-USB INTERFACE ................................................................................................................17

4.5.1- Assignments of USB connector terminals USB.......................................... 18

5 – BASIC OPERATIONS.........................................................................................................19

5.1-PAPER LOADING................................................................................................................19

5.2-BUTTON FUNCTIONS........................................................................................................19

5.3-PAPER SENSORS ..............................................................................................................19

5.4-OPEN PLATEN SENSOR ..................................................................................................20

5.5-NEAR-END PAPER SENSOR...........................................................................................20

5.6-LED INDICATOR .................................................................................................................20

5.7-SPECIAL PRINTING MODES............................................................................................20

5.7.1- Self-test mode ............................................................................................. 20

5.7.2- Programming mode..................................................................................... 21

5.7.3- Hexadecimal dump mode............................................................................ 22

5.8-ERROR PROCESSING ......................................................................................................22

5.8.1- Error types................................................................................................... 22

5.8.2- Printer operation when an error happens.................................................... 24

5.8.3- Data reception error (serial interface only).................................................. 24

5.8.4- Flow diagram of the error detection for the serial port................................. 24

5.8.5- Flow diagram of the error detection for the parallel port.............................. 25

6 – CONTROL COMMANDS ....................................................................................................26

6.1-COMMAND NOTATION......................................................................................................26

6.2-TERM DEFINITIONS...........................................................................................................26

6.3-DESCRIPTION OF THE CONTROL COMMANDS........................................................27

APPENDIX A – SPECIFICATIONS ..........................................................................................43

APPENDIX B – MECHANICAL DIMENSIONS .........................................................................44

APPENDIX C – HOW TO ORDER ...........................................................................................45

EPC1200 SERIES OPERATION MANUAL

3/58

APPENDIX D – CODE128 BAR CODE ....................................................................................47

D.1 Description of the CODE128 Bar Code ...........................................................................47

D.2 Printable characters in CODE SET A...............................................................................48

D.3 Printable characters in CODE SET B...............................................................................49

D.4 Printable characters in CODE SET C ..............................................................................50

APPENDIX E – INTERNAL CHARACTER TABLES.................................................................51

APPENDIX F – TESTING SOFTWARE....................................................................................52

APPENDIX G – INTERFACE IF1200 .......................................................................................54

APPENDIX H – PTR2 ...............................................................................................................56

FIGURES AND TABLES

Fig. 1. - Thermal print head cleaning ......................................................................................................... 6

Fig. 2. - EPC1200 accessibility .................................................................................................................. 9

Fig. 3. - Fixing holes and window to be cut on the mounting wall ........................................................... 10

Fig. 4. - Application of a self-stand PTR2 with the EPC1200. ................................................................. 10

Fig. 5. - Power supply connector CON1. ................................................................................................. 11

Fig. 6. - FENIX supplied 5VDC power modules....................................................................................... 12

Fig. 7. - Current consumption example.................................................................................................... 12

Fig. 8. - Serial RS-232 interface pins....................................................................................................... 13

Fig. 9. - PC serial cable............................................................................................................................ 14

Fig. 10. - Timing diagram of data reception ............................................................................................. 15

Fig. 11. - Parallel interface pins ............................................................................................................... 16

Fig. 12. - PC parallel cable....................................................................................................................... 17

Fig. 13. - EPC1200 USB connector. ........................................................................................................ 18

Fig. 14. - Paper orientation ...................................................................................................................... 19

Fig. 15. - SELF-TEST mode example...................................................................................................... 20

Fig. 16. - PROGRAMMING MODE example ........................................................................................... 21

Fig. 17. - HEXADECIMAL DUMP mode example.................................................................................... 22

Fig. 18. - LED Blinking sequence (RED) ................................................................................................. 23

Fig. 19. - Serial port error flow diagram ................................................................................................... 24

Fig. 20. - Nibble mode phase transitions ................................................................................................. 25

Fig. 21. - Code128 bar code .................................................................................................................... 39

Fig. 22. - Logo loading ............................................................................................................................. 42

Fig. 23. - Mechanical dimensions ............................................................................................................ 44

Fig. 24. - Demo Program ........................................................................................................................ 52

Fig. 25. - IF1200....................................................................................................................................... 54

Fig. 26. - IF1200 Mechanical Dimensions ............................................................................................... 55

Fig. 27. - PTR2 Fixing Options................................................................................................................. 56

Fig. 28. - Back connector as seen from outside the printer. .................................................................... 57

Fig. 29. - PTR2 Mechanical dimensions .................................................................................................. 57

Table 1. - Pins Assignments of RS-232 connector terminals .................................................................. 13

Table 2. - Timing of parallel communication protocol .............................................................................. 15

Table 3. - PC parallel connector (DB25).................................................................................................. 16

Table 4. - Command List.......................................................................................................................... 27

EPC1200 SERIES OPERATION MANUAL

4/58

The EPC1200 is a high performance thermal panel printer series. Its compact and functional

design covers many professional uses (as in supermarkets, hotels, hospitals, restaurants, and so on.) It

is capable of printing text, graphics, logo and barcodes. It can be used in laboratories, industrial and

professional environments.

The PTR2 consist of a EPC1200-12 printer with serial interface enclosed into a metal chassis.

The main features of the EPC1200 Series are:

•Simple installation and easy maintenance.

•Low noise thermal printing.

•Paper width: 58 mm.

•High reliability: 100 million pulses. Abrasion resistance: 50 Km.

•Power supply, two options: 5VDC or 12-24VDC, depending on the interface.

•No-paper sensor.

•Near-to-end paper sensor (only on the 12-24VDC models)

•Up to 45 mm paper roll diameter.

•High speed printing up to 90mm/s (EPC1250 prints up to 50mm/s).

•Printing resolution: 8 dots/mm (203 dpi).

•Passive paper cut.

•Interface: - Option 1: IEEE 1284 parallel and serial RS232C data input interface

on-board (up to 115200bps).

- Option 2: Universal Serial Bus (USB) communications port on-board.

•Two internal character fonts (A font = 12x24 dots. B font = 8x16 dots).

•Scalable font (independent scale in X/Y-axis), up to 64 times.

•Programmable character and line space.

•Bold and reverse character capabilities

•Graphic bitmap printing capabilities.

•Several format Bar Code (EAN13, Code39, Code128 and ITF)

•Control code based on ESC/POS commands (1).

•Hexadecimal mode for easy software debugging.

•Automatic paper load.

•Three maintenance counters (On/Off times, Half hours, Meters)

•Operating temperature range (0ºC to +50ºC).

•Storage temperature range (-20ºC to +70ºC).

•Self test, hexadecimal mode and configuration mode features.

•Logo load capability, through Windows driver.

•Upgrading of firmware version through communication port (2)

•Windows 2000 and XP drivers and demo/configuration program.

•Linux Driver.

(1) ESC/POS are registered trademarks of Seiko Epson Corporation.

(2) Only in EPC1200-12-U and PTR2 printers

The EPC1200 Printer Series comprises the following models:

EPC1200-5 5VDC, 90mm/s printing speed, serial and parallel interface

EPC1200-12 12-24VDC, 90mm/s printing speed, serial and parallel interface

EPC1200-12-U 12-24VDC, 90mm/s printing speed, USB interface

EPC1250 5VDC, 50mm/s printing speed, serial and parallel interface

PTR2 12-24VDC, 90mm/s printing speed, serial interface

This manual is the printer operations’ guide and is intended for the designer’s application. The

following sections contain a detailed description of both hardware and configuration software that allow

obtaining the maximum benefit of the printer capabilities.

1 – INTRODUCTION

EPC1200 SERIES OPERATION MANUAL

5/58

In order to preserve the life of the printer, it is necessary to keep in mind some precautions on the

handling of the EPC1200 printer. Please read carefully the following points in order to make a good use

of the printer.

2.1- SAFETY PRECAUTIONS

•Before using the printer, read carefully section 2-INSTALLATION.

•NEVER connect the external power supply with the wrong polarity. This could permanently

damage the printer.

•Turn off the printer immediately if it produces smoke, a strange smell or an unusual noise. Keeping

on using the printer could cause fire. Unplug the equipment immediately and contact your official

distributor.

•NEVER connect cables with different connectors from the ones mentioned in this manual. Failing

on doing so could permanently damage the printer.

•Use a power supply whose output voltage is within the specification range stated in this manual.

Over voltage can permanently damage the printer. Under voltage can cause malfunctions.

•NEVER wet EPC1200 thermal printer with water or any other liquid. If any liquid is spilled inside

the equipment, unplug the power cable immediately and contact the technical service.

•Make sure the printer is on a steady, securely fixed surface. If the printer falls down, it could break

or damage.

•NEVER use the printer in high humidity or in locations with high risk of fire.

•NEVER place heavy objects on top of the printer and never lean on it.

•NEVER put any object inside of the printer, as it could cause hardware damage on it, such as

short-circuit, print head breaking or general failure of the printer.

•NEVER shake the printer.

•NEVER disassemble or modify the hardware of the printer.

•NEVER try to repair the printer. Please contact your official distributor in case of failure.

•As the printer contains electromagnets (inside of the motor), it should not be used in excessively

dirty environments or places with dust or metal particles.

•NEVER print without paper loaded or without the cover closed, as the thermal print head life can

be highly shortened.

•Avoid touching accessible parts with metallic objects, such as screwdrivers or tweezers, the print

head thermal elements as well as the electronic printed circuit. They are delicate parts.

•NEVER touch with bare hands the areas around the print head and the motor surface as they

become very hot during and just after printing; wait 15 seconds after printing to let them cool down.

•NEVER touch the surfaces of the print head thermal elements or the electronic printed circuit, as

dust and dirt can stick to their surface and cause damage by electrostatic discharge. Moreover,

some electronic components can get very hot during operation.

•The thermal paper contains Na+, K+ and Cl- ions that can cause harm to the print head elements.

Therefore, use only the specified paper.

•If the printer has not been used for long period of time and the paper was loaded, the paper could

become deformed by the drive roller pressure. It is recommended to make it advance at least 30

mm before printing again.

•For safety reasons, unplug the printer if it is not going to be used over a long period of time.

•Do not print continuously (without stopping) for more than 6 minutes.

2.2- ABSOLUTE MAXIMUM RATINGS

Supply voltage

EPC1200-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +30 V

EPC1200-5 . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +10 V

EPC1250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5.6 V

PTR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +30 V

Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20°C to 70°C

2– IMPORTANT NOTES ON EPC1200 THERMAL PRINTER HANDLING

EPC1200 SERIES OPERATION MANUAL

6/58

2.3- CLEANING PROCEDURE AND PRECAUTIONS

In order to clean the thermal print head, proceed as indicated by the following steps:

1- Unplug the power supply cable and open the front door.

2- Remove the paper roll and the thermal print head will be accessible from downwards.

3- Soak a cotton sponge in alcohol (ethanol, methanol or IPA), and rub it gently along the

thermal head in order to remove the possible accumulation of paper particles.

4- Wait for alcohol to evaporate before inserting the paper roll and closing the cover.

FENIX recommends cleaning the thermal print head periodically (every 2 or 3 months) in order

to keep an optimal print quality.

NOTES:

9The print head could be hot after printing. Make sure it has thoroughly cooled down

before proceeding to clean it.

9Never touch the thermal elements of the print head with your hands.

9Never use metallic or piercing elements to clean the print head, as they could scratch it.

Fig. 1. - Thermal print head cleaning

2.4- RECOMMENDATIONS

•The plug has to be located near the printer and has to be easily obtainable.

•Before connecting any communication data cable, check the printer is working properly by

executing the self-test.

•Set the EPC1200 in a place where the connection cables do not suffer stretching or cross with

each other.

•IMPORTANT!!! Since the printer demands high current peaks during operation it is advisable to

make the power supply cables the shortest possible. Otherwise the supply voltage could fall

below limits causing malfunction of the printer, especially on the 5VDC model.

EPC1200 SERIES OPERATION MANUAL

7/58

3.1- PRINTING SPECIFICATIONS

EPC1200 / PTR2 EPC1250

Printing method Thermal line printing

Dot density 203 dpi x 203 dpi

(1)

Printing direction Unidirectional with friction feed

Printing width 48 mm (384 dots)

Printing speed

(2)

High speed mode:

up to 90mm/s

up to 50mm/s

Paper feed speed 90 mm/s (continuous

paper feed)

50 mm/s (continuous

paper feed)

Characters per line (by default): A font: 24

B font: 32

Space between characters (by default): 4 dots (0.5 mm)

Line spacing (by default): 3.75mm

(1) ‘dpi’: dots per inch. 1 inch = 25.4mm; 203 dpi = 8 dots per mm

(2) Printing speed could vary depending on the print head temperature as well as the

command processing and the data transmission speed. Low printing speed could

cause intermittent printing. It is recommended to transmit data to the printer as quickly

as possible.

3.2- CHARACTER SPECIFICATIONS

1) Number of characters: Alphanumeric characters: 95

Extended graphics: 128 per page

2) Character structure: A font: 12 x 24 dots (1.5 x 3 mm). (selected by default)

B font: 8 x 16 dots (1 x 2 mm).

3) Character size:

Standard Double height Double width Double width

Double height

Width x height cpl Width x height cpl Width x height cpl Width x height cpl

A Font 1,5 x 3 mm 24 1,5 x 6 mm 24 3 x 3 mm 12 3 x 6 mm 12

B Font 1 x 2 mm 32 1 x 4 mm 32 2 x 2 mm 16 2 x 4 mm 16

The space between the characters is not included. Characters can be scaled up to 64 times bigger than their

normal size.

cpl: characters per line.

3.3- PAPER SPECIFICATIONS

1) Paper type: thermal paper roll

2) Paper width: 58 +0/-1mm

3) Paper roll size: up to a maximum diameter of 45 mm

4) Specified thermal paper: At –5ºC to 50ºC ÆTF50KS-E2D (59μm paper)

TF77KS-E2 (95μm paper)

TL69KS-HG76 (label paper)

At –30ºC to 70ºCÆTL51KS-R2 (High heat-resistant paper)

TL69KS-R2 (High heat-resistant paper)

At 5ºC to 40ºC ÆTW80KK-S (2-ply thermal paper)

From Nippon Paper Industries

3.4- PAPER LOADING

One of the main advantages of the EPC1200 printer series is its paper loading system. It can be

carried out by any final user without having to disassemble the printer or loading the paper in a complex

paper path.

3 –GENERAL SPECIFICATIONS

EPC1200 SERIES OPERATION MANUAL

8/58

10 12 14 16 18 20 22 24 26

500

1000

1500

2000

2500

3000

3.5- INTERNAL BUFFER

The standard EPC1200 printer has a 10 Kbytes internal memory buffer, whose functionality is

dynamically shared by the receiving buffer. The USB version and PTR2 have an additional 512 Kbytes

memory buffer.

This big receiving buffer allows the printer working in the following way: Firstly, all data is buffered,

and afterwards the printing is performed at the maximum possible speed without being affected by the

communications time processing.

3.6- ELECTRICAL SPECIFICATIONS

- Power supply voltage: 5VDC+10%-3% or 12-24VDC±10% depending on the interface.

- Current consumption: The table and chart below show the current consumption for different

supply voltages. Measurements have been done for the following cases:

•Printer powered on (stand-by)

•Printer feeding paper but no printing

•Printer printing at rates of 25%, 50%, 75% and 100% of dots activated each line (chart)

3.7- ENVIRONMENTAL CONDITIONS

Temperature range: Working temperature: 0º to 50ºC.

Storage temperature: -20º to 70ºC with no paper loaded, in a dry place.

Printer Model Supply

Voltage

(V)

Stand-by

current

(mA)

Feeding paper

current

(mA)

25%

Printing

Ratio

50%

Printing

Ratio

75%

Printing

Ratio

100%

Printing

Ratio

EPC1250 5 210 500 1750 2780 4265 5390

EPC1200 5 395 850 2155 4250 5250 7150

EPC1200-X-12 / PTR2 12 135 335

SEE CHART BELOW

EPC1200-X-12 / PTR2 15 110 280

EPC1200-X-12 / PTR2 20 90 220

EPC1200-X-12 / PTR2 24 75 190

Average Current

Consumption

(mA)

Supply Voltage

(V)

25%

50%

75%

100%

EPC1200 SERIES OPERATION MANUAL

9/58

4.1- EPC1200 INSTALLATION CONSIDERATIONS

There are some general considerations to take into account when installing the EPC1200 printer.

For PTR2 installation please refer to APPENDIX H – PTR2.

A wrong installation may cause many issues like paper jam, difficult maintenance of the printer,

difficulty in changing the paper roll, etc. Moreover, a correct installation can prevent the printer from

being damaged by external agents, such as weather or vandalism.

This printer is thought to be installed vertically in a bigger case or structure, or another kind of

appropriate chassis.

The basic points that a correct installation must follow are:

•Allow enough space and accessibility to reach the maintenance procedure points in case it

is needed. Take notice all user accessible parts in the printer.

•Consider if the printer is going to be attached first to the panel and then connected or the

other way round. The EPC1200 allows both ways but cable length and some other variables

should have been taken into consideration.

•Allow enough room in front of the printer in order to be able to open completely the door.

Minimum closet depth (EPC1200) = 72mm

Fig. 2. - EPC1200 accessibility

This printer has been designed to ease the installation process and maintenance. Please follow

the recommendations below so there should not be any issue related to it.

4 – INSTALLATION

EPC1200 SERIES OPERATION MANUAL

10/58

1) The printer must be set onto the user’s chassis and screwing it from outside. To do so cut a

window with the dimensions indicated on the figure and thread four holes as shown.

Fig. 3. - Fixing holes and window to be cut on the mounting wall

2) All the wiring has been designed to allow the user to firstly connect the cables and then screw

the printer onto the panel although the other way is also possible. If it is difficult to access the

rear side of the printer it is advisable to connect all the cables first and perform a self-test

before fixing the printer to the mounting wall.

Fig. 4. - Application of a self-stand PTR2 with the EPC1200.

Table des matières

Autres manuels Fenix Imvico Imprimante

Fenix Imvico

Fenix Imvico KS55 Series Manuel utilisateur

Fenix Imvico

Fenix Imvico TS1700 Manuel utilisateur

Fenix Imvico

Fenix Imvico TK23 Series Manuel utilisateur

Fenix Imvico

Fenix Imvico SM3000 Manuel utilisateur

Fenix Imvico

Fenix Imvico TK14 Manuel utilisateur

Fenix Imvico

Fenix Imvico TK41 Manuel utilisateur

Fenix Imvico

Fenix Imvico TK51 Series Manuel utilisateur

Fenix Imvico

Fenix Imvico EPC1100 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur