F5 ARX-4000 Manuel d'utilisation et d'entretien

ARX 4000 / D103 Parts Replacement

Guide

June 20, 2014

Version 1.4

- 1 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Removing the Front Bezel

The ARX 4000 employs a highly modular design that allows several key components to be replaced on

a FRU basis. Several of these FRU’s can only be reached by removing the Front Bezel.

Step 1 Remove front bezel

Using the two cutouts on the lower half on either side of the data plane pull gently on the bezel

Fig. 13

- 2 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Installing the Bezel

Step 1 Installing Bezel

Push Bezel until fully seated

Fig. 14

- 3 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 Chassis Overview –Front without bezel

ARX-4000+

- 4 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 /4000+ Control Plane Differences

- 5 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000+ Chassis Overview –Front without bezel

- 6 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000 Chassis Overview –Rear

- 7 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

ARX 4000+ Chassis Overview –Rear

- 8 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Replacing a X2 module

Preparation

Before beginning ensure that the Field Tech understands that work will be done only on the

Backup Switch.

Verify that the Tech can identify the Backup and the Active and the active switch is fully

functional.

Ensure the correct X2 module needs to be replaced. There are two X2 modules 2/1 and 2/2.

They are labeled as such on the bottom of the slot. 2/1 is the left-most and 2/2 is the right-

most, if facing the front of the switch.

Removing a X2 module

Take the Field Tech through the following steps:

Step 1 Tag the cable so that it will be easily identifiable later

Step 2 Remove the fiber optic cable from the X2 module

Step 3 Grasp both sides of the locking mechanism

Step 4 Pull forward on the locking mechanism

Fig. 1

- 9 –

Copyright © 2008, F5 Networks, Inc. All rights reserved.

Installing a X2 module

Step 1 Place the X2 module into the slow heat sink side up

Fig. 2

Step 2 Push forward on the X2 module until fully seated in the slot

Fig. 3

Autres manuels pour ARX-4000

1

Table des matières

Autres manuels F5 Matériel réseau

F5

F5 ARX-500 Manuel

F5

F5 i5000 Series Instructions de montage

F5

F5 6900 Instructions de montage

F5

F5 BIG-IP 3900 Manuel utilisateur

F5

F5 6900 Manuel utilisateur

F5

F5 i4000 Series Instructions de montage

F5

F5 iSeries Manuel utilisateur

F5

F5 WANJet 500 Instructions de montage

F5

F5 8900 Instructions de montage

F5

F5 Herculon SSL Orchestrator Manuel

F5

F5 ARX-500 Manuel d'utilisation et d'entretien

F5

F5 BIG-IP 1600 Instructions de montage

F5

F5 i15000 Series Instructions d'utilisation

F5

F5 520 Manuel utilisateur

F5

F5 WANJet 300 Manuel technique

F5

F5 BIG-IP 11050 Manuel utilisateur

F5

F5 WANJet 500 Manuel technique

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur