Ezviz LT70 Manuel utilisateur
1
Instruction
• The installation of EZVIZ Smart Fingerprint Lock (hereinafter referred as to "lock") impacts its normal operation
and service life. It is recommended to let professionals install, and drill hole for lock set in accordance with hole
templet in appendix.
• It is recommended to remove the lock if your house is under decoration, and reinstall it after decoration in case
of lock damage and service life reduction.
• Please note that disinfectant may cause damage to the lock body.
• Once initialized completed, the lock will clear all user information. After lock installation and configuration,
please add fingerprint, passcode or card as needed.
• When battery voltage is low after using for a while, low voltage alarm alerts. Replace battery timely and pay
attention to positive and negative poles.
• If you leave home or do not use lock for a long time, keep mechanical key with you, and do not leave it indoors.
You should take battery out to ensure lock service life.
• Considering that the lock is put in an open environment, we suggest you pay attention to the safety in use,
including keep properly small parts like the mechanical key or the sensing card. You should check the surrounding
environment before unlocking and updating your passcode and sensing card settings on time as well in case of
any danger of illegal stealing or copying of your unlocking information.
• For users with flat or thin fingerprint, it is recommended to use thumb to register fingerprint for inceasing
success rate, and register more than one fingerprint with the same user. the same user supports a maximum of
5 fingerprints.
• The lock accommodates up to 100 fingerprints, 100 passcodes and 100 cards.
2
Packing List
Front Panel (×1) Rear Panel (×1)
Hole Templet (×1) Lock Body (×1) Standard Screw Bag (×1)
AA-sized Battery (×8) Key Bag (×1) Square Rod (×1)
Card (x2) Lock Body Screw Bag (×2) Regulatory Information
(×1) Quick Start Guide (×1)
4
Get the EZVIZ App
1. Connect your mobile phone to 2.4GHz Wi-Fi (suggested).
2. Download and install the EZVIZ app by searching for “EZVIZ” in the App Store or Google PlayTM.
3. Launch the app and register an EZVIZ user account.
EZVIZ App
If you have already used the app, please make sure that it is the latest version. To nd out if an update is
available, go to the app store and search for "EZVIZ".
Add the Lock to EZVIZ
The app interface may be different due to version update, and the interface of the app you installed on your
phone shall prevail.
Please add lock to EZVIZ by following steps:
1. Log in to your EZVIZ app account.
2. On the Home screen, tap “+” on the upper-right corner to go to the Scan QR Code interface.
3. Scan the QR code on the battery slot.
4. Follow the EZVIZ app wizard to add the lock to EZVIZ app account.
5
Lock Settings
After installation, remove back cover of battery slot and install 8*AA-sized batteries. Then you can set the lock
as needed.
• Please remove protective film from lock before the first use.
• Please note that disinfectant may cause damage to the lock body.
1� Keypad
~: number key
: cancel, return or exit
: doorbell, conrm, initialization setting
2� Enter Menu
Please follow these steps for settings.
• In initial state, follow these steps for settings.
1 Press the SET button.
or touch the keypad area to activate the
lock.
2 "*" "#" on keypad light up.
• Press "*" to exit.
• Press "#" add an
administrator.
3 "1" "2" "3" "*" on keypad light up.
• Press "1" to add a fingerprint.
• Press "2" to add a passcode.
• Press "3" to add a card.
• Press "*" to exit/ return.
Method 1 Method 2
In non-initial state, follow these steps for settings.
1 Press the SET button. 2 Verify with administrator's ngerprint,
passcode or card.
3 "1" "2" "3" "4" "*" on keypad light
up.
6
3� Menu Index
The menu here is for reference only.
1 2
3
4
2
3
1
1
2
3
2
3
1
Menu
Add new administrator
Add new user
Delete administrator/user
System information
Add ngerprint
Add passcode
Add card
Add ngerprint
Add passcode
Add card
4� Add Administrators/Users
1 Enter the menu.(For detailed operations,
please refer to "Enter Menu")
2 Press "1" to add an administrator, or press "2" to add a user.
Role Unlock the door Enter the Menu, and set the lock
Administrator √ √
User √X
Ordinary users can only unlock the door after entering the opening method; the administrator can not only
unlock the door, but also log in to the menu to add and delete users and operate other settings.
When you add an administrator or a user, the gures corresponded to the user number will light up from
001 by default ( for example, to user number 001, the three numbers 001 will slow-flash once in sequence).
7
5� Delete Administrators/Users
1 Enter the menu.(For detailed operations,
please refer to "Enter Menu")
2 Press "3" to delete an
administrator/a user.
3 Enter the user number and
press #.
• If you pressed a wrong user number, the number “1, 3, 5, 7, 9” (seems like a X ) on the keypad will light up
and flash 2 times, accompanied by a failure beep. Press "*" to return to last step, or enter the user numbers
to delete again.
• When there is only one user left, and you operate to delete it, the number “1, 3, 5, 7, 9” (seems like a X ) on
the keypad will light up and flash 2 times, accompanied by a failure beep.
6� Look Up to the System Information
1 Enter the menu. (For detailed operations,
please refer to "Enter Menu")
2 Press "4" to look up to the
system information of the lock.
3 The lock broadcast the
system information.
The lock will broadcast the lock serial number, the current device version and verication code in English in
turn, press * to return to the previous level. Or the system will return to the previous level automatically after
the successful broadcast.
7� Add Fingerprint
1 Enter the menu.(For detailed operations,
please refer to "Enter Menu")
2 Press "1" to add an administrator, or press "2" to add a user.
8
3 Press "1" to add a ngerprint.4When "1" lights up, touch the
ngerprint reader and repeat the
operation 6 times, 1~6 light up one by
one, accompanied by a success beep,
the ngerprint is successfully added.
• Press "1" to add fingerprints
continuously.
• Press the * key to return to the
previous level.
• Press the SET button to exit.
8� Add Passcode
1 Enter the menu.(For detailed operations,
please refer to "Enter Menu")
2 Press "1" to add an administrator, or press "2" to add a user.
3 Press "2" to add a passcode. 4
Enter the corresponding 6-10 digit
valid passcode .when the passcode
input key ≥ 6 digits, "#" lights up at this
time, press "#" to conrm.
Repeat the passcode once again,
press "#" to conrm, accompanied
by a success beep, the passcode is
successfully added.
9
9� Add Card
1 Enter the menu.(For detailed operations,
please refer to "Enter Menu")
2 Press "1" to add an administrator, or press "2" to add a user.
3 Press "3" to add a card. 4
Place the unrecorded proximity
card on the card swipping area.
• Press # key to conrm.
• Press * key to return to the
previous level.
10� Finish the Wi-Fi Conguration
Press and hold the SET button for more than 3s. When "0" starts flashing
accompanied by a beep,
it means the Wi-Fi
conguration mode is turned on.
Please follow the system guide to nish the Wi-Fi Conguration in 5minutes.
The system will exit the Wi-Fi conguration mode automatically after 5minutes.
10
Lock Using
Multiple Unlock Methods
Fingerprint unlock Passcode unlock
card unlock key unlock
• When openning the door by mechanical key, rotate the key and down press the handle.
• Please touch the keypad area to activate the lock before opening the door by passcode.
• For your privacy security, it is recommended to change passcodes and clean keypad area regularly in case
of remaining marks.
1� Fingerprint Unlock
• This product has security protection function, fingerprint recognition error number reaches 5 times
continuously in 5minutes, the system will be locked forcibly for 3 minutes.
• The system will be unlocked automatically after 3 minutes.
• You can turn off this function in EZVIZ app.
1 Put your nger on the ngerprint reader. 2 When you hear the voice prompt, put down the handle
to open the door.
2� Passcode Unlock
• This product has security protection function, passcode recognition error number reaches 5 times
continuously in 5 minutes, the system will be locked forcibly for 3 minutes.
• The system will be unlocked automatically after 3 minutes.
• You can turn off this function in EZVIZ app.
• The product has protect with Anti-Peeping Passcodes. In case someone is watching you entering a
passcode, you can add extra-long digits before or after your original code to make it complex, while still
being able to unlock.
Autres manuels pour LT70
1
Table des matières
Autres manuels Ezviz Serrure de porte
