Ezviz L2 Manuel utilisateur
2
Instruction
• The installation of EZVIZ Smart Fingerprint Lock (hereinafter referred as to "lock") impacts its normal
operation and service life. It is recommended to let professionals install, and drill hole for lock set in
accordance with hole templet in appendix.
• It is recommended to remove the lock if your house is under decoration, and reinstall it after decoration in
case of lock damage and service life reduction.
• Please note that disinfectant may cause damage to the lock body.
• Once initialized completed, the lock will clear all user information. After lock installation and conguration,
please add ngerprint, password or card as needed.
• When battery voltage is low after using for a while, low voltage alarm alerts. Replace battery timely and pay
attention to positive and negative poles.
• If you leave home or do not use lock for a long time, keep mechanical key with you, and do not leave it
indoors. You should take battery out to ensure lock service life.
• For users with at or thin ngerprint, it is recommended to use thumb to register ngerprint for inceasing
success rate, and register more than one ngerprint with the same user.
• The lock accommodates up to 50 ngerprints, 50 passwords and 50 cards.
Overview
Indoor
Outdoor
Fingerprint Reader
Keypad
Card Swiping Area
Doorbell Button
Lever Handle
Emergency Power Supply Interface
Mechanical Keyhole
Battery Cover
Anti-Peephole Button
Lever Handle
Secure Knob
3
Lock Installation
Switch Lever Handle Direction (Optional)
1.Switch Lever Handle Direction
- Take off the rubber and remove the reversing screw with screwdriver.
- Rotate the lever handle 180 degrees upwards.
- Screw the reversing screw into the opposite screw hole.
Reversing Screw
2.Conrm Clutch Direction
- Front panel: Insert square rod into sleeve and lift lever handle. Rotate sleeve 90 degrees if lever handle idles.
- Rear panel: Turn on the anti-peephole button. Insert square rod into sleeve and lift lever handle. Rotate
sleeve 180 degrees if lever handle idles.
Elastic Cylinder Pin
Front Panel Rear Panel
Square Rod
Anti-Peephole Button
4
Switch Lock Latch Bolt (Optional)
1
2
3
Uplift the metal here.Rotate the latch bolt 180 degrees.
Turn the central part 90 degrees and
tuck it in.
Push the latch bolt into the
lock body.
Installation Steps
• The standard accessories for this product support installation for 40mm-50mm wooden doors. If the thickness
of the door is beyond this range, please contact your local dealer.
• When xing front and rear panel, do not press internal connection cable.
• When installing front and rear panel, handle with care in case of any panel damage.
1.Drill Hole
The product is applicable to wooden door and burglar-proof metal door. Drill hole in accordance with hole
templet in packing list.
2.Install
Please visit the link below to watch the installation video.
https://support.ezvizlife.com/videos/map?id=38&title=How%20to%20Install%20L2
5
1 Fix lock body into door panel with screws.
Door
Screws
Lock Body
Locating Hole
Hook
2 Insert square rod into front panel and install front panel into door as shown below.
Front Panel
Square
Rod
Locating
Pin
Screwed
Conduit
6
3 Fix the xed plate and rubber pad into the door with ①locating pin and ② tighten sleeve.
Fixed Plate Rubber Pad
4 With the secure knob keeping upright, x the rear panel with screws as shown below.
Rear Panel
Secure Knob
Secure Pick
7
Lock Settings
After installation, remove back cover of battery seat and install 4*AA-sized batteries. Then you can set the
lock as needed.
Please visit the link below to watch the setup video.
https://support.ezvizlife.com/videos/map?id=39&title=How%20to%20Setup%20L2
• Please remove protective lm from lock before rst use.
• Please note that disinfectant may cause damage to the lock body.
Activate Lock
Touch keypad area to activate the lock.
Enter Menu
Press 3571# to enter menu.
• In initial state, enter short code for settings.
• In non-initial state, verify with added ngerprint, password or card rst. Then enter short code for settings.
Menu Index
Menu
11#
12#
13#
Add Fingerprint
Add Password
Add Card
21#
22#
23#
Delete Fingerprint
Delete Password
Delete Card
31#
32#
33#
Clear Fingerprint
Clear Password
Clear Card
41#
42#
43#
High Volume
Low Volume
Mute
3570# Initialize
After every successful setting, you will return to the menu. Then you can enter short code again to set or press *
to exit.
8
Add Fingerprint/Password/Card
Add Fingerprint
1 After entering the menu, press 11# to add
ngerprint.
2 Touch ngerprint reader. Then touch again after
voice prompt and repeat the operation for 5 times
to conrm. The ngerprint number will ash on
the keypad when complete.
• The number of times will be displayed on the keypad each time you touch the ngerprint reader.
• Please keep in mind the ngerprint number, which is required if you want to delete the ngerprint.
• Fingerprint which has been added cannot be added again.
Fingerprint Collection
When collecting ngerprint, please adjust your nger to maximize the ngerprint contact surface as shown
below, which helps to improve ngerprint verication success rate.
Add Password
1 After entering the menu, press 12# to add
password.
2 Enter password (6 to 10 digits) and press #. Then
enter password and press # again to conrm.
The password number will ash on the keypad
when complete.
• Please keep in mind the password number, which is required if you want to delete the password.
• Password which has been added cannot be added again.
9
Add Card
1 After entering the menu, press 13# to add
card.
2 Swipe card. The card number will ash on the
keypad when complete.
• Please keep in mind the card number, which is required if you want to delete the card.
• Card which has been added cannot be added again.
Delete Fingerprint/Password/Card
Delete Fingerprint
1 After entering the menu, press 21# to delete
ngerprint.
2 Enter ngerprint number and press #.
3 The ngerprint number ashes and then
press #.
The current veried ngerprint cannot be deleted.
For example, if you verify with ngerprint 1, then ngerpint 1 cannnot be deleted.
10
Delete Password
1 After entering the menu, press 22# to
delete password.
2 Enter password number and press #.
3 The password number ashes and then
press #.
The current veried password cannot be deleted.
For example, if you verify with password 1, then password 1 cannnot be deleted.
Delete Card
1 After entering the menu, press 23# to delete
card.
2 Enter card number and press #.
3 The card number ashes and then press #.
The current veried card cannot be deleted.
For example, if you verify with card 1, then card 1 cannnot be deleted.
11
Clear Fingerprint/Password/Card
1 After entering the menu,
press 31# to clear ngerprints,
press 32# to clear passwords,
press 33# to clear cards.
2 Press # to conrm.
The current veried method cannot be cleared.
For example, if you verify with ngerprint, then ngerpints cannnot be cleared.
Initialize
1 After entering the menu, press 3570# to
initialize.
2 Press # to conrm.
Volume Control
After entering the menu, press 41# to select High Volume,
press 42# to select Low Volume,
press 43# to select Mute.
Only key sound and verication sound can be muted.
Table des matières
Autres manuels Ezviz Serrure de porte
