EZCast Beam V3 Manuel utilisateur
V3
EZCast Beam V3 Quick Start Guide
This EZCast Beam V3 Quick Start Guide provides a
guideline for basic operation. Please read the guide
thoroughly before operating the projector. Visit
www.EZCast.com for additional information. Product
information is subject to change without prior notice.
Thank you for purchasing the EZCast Beam V3 projector. Our product
combines the easy to use interface, portability, and cross platform
compatibility, to let you enjoy projecting media from Android, iOS phones
and tablets, as well as Windows and MacOS laptops, anytime, anywhere.
Please visit www.EZCast.com/app to download EZCast app for every
supported platform.
Mobile devices can proceed to the relevant download area by scanning
the QR code below.
(iOS users can search for EZCast in the App Store to download the app)
(Android users can search for EZCast in Google Play to download the
app)
EZCast app installation
1. Do not turn the lens toward human eyes when in operation, to avoid
damaging the eyes caused by the high intensity light source.
2. Do not block the device ventilation to avoid damage to the internal
electronic devices due to overheating.
3. Do not use chemicals, cleaning agents or clean water to clean the
device, and prevent rain water, moisture and mineral-containing liquids
from corroding circuit boards.
4. Please keep the device and its parts and accessories out of reach of
children.
5. Please ensure that the device is operated in a dry and ventilated
environment.
6. Do not store the device in extreme hot or cold conditions. High and low
temperatures may shorten the lifespan of electronic devices. The normal
operating environment is between 5°C~30°C.
7. Do not put the device into any drying equipment (such as dryer,
microwave oven, etc.).
8. Do not squeeze or place heavy objects over the device to avoid
damage to the device.
9. Do not throw, knock or shake the device violently, which may damage
the internal circuit boards.
10. Do not attempt to disassemble the device without permission. If there
is any problem, please contact customer support.
11. Do not repair any product by yourself. If the device or any part does
not work properly, you should consult customer support or return the
device for repair.
12. It is recommanded to shut down for 30minutes after playing for more
than 8 hours.
Never look directly into the projector lens when the lamp is
turned on.The bright light can damage your eyes.Never let
children look into the lens when it is on.
Precautions
How to use the projector
EZCast Beam V3 body and remote
Speaker
mode
Select
Back
Volume
up
Volume
down
Arrows
Power
Home
Settings
OK
Lens
Focus Ring
Mobile Stand Control Panel
Wireless Kit
DC
USB
HDMI
Headset Jack
Micro SD
Remote Sensor
Ventilation
(Do not block)
Power
Settings
Home
Back
Select
Arrows
OK
How to set up EZCast Beam V3 projector
Preparation
1. Plug the power to the projector, and the power button will light up.
2. Insert the wireless adapter into the wireless kit port of the projector.
3. To turn on projector, hold the power button of the projector for 3
seconds till you hear the "beep” sound and the light will turn blue.
4. Adjust focus ring until the projection image is clear and focused.
(Do not block)
Project forward Project upward
Projector stand
Ventilation
Holders
(Do not block)
Ventilation
(Do not block)
Ventilation
Wireless
Adapter
HDMI
DC
Projector stand and holders
1. Normal mode: When projecting forward, adjust elevation angel by
loosening the projector stand under the projector. When projecting
upward, use the holders to avoid blockage of ventilation.
2. Portrait mode: Equip the projector holders at the bottom to make sure
the ventilation works well.
(Normal mode) (Normal mode) (Portrait mode)
OK
First time settings
1.Select the start-up language.
2. Wi-Fi setting: connect the projector to your router and enter the
password. (Important)
3. After starting up, enter the main menu and select the functions by
arrow keys on the projector or remote control: Android, iOS, MacOS,
Windows, bluetooth, EZCast, Multimedia, HDMI, and Setting, as below
shown:
Multimedia playback
1. Insert a USB flash drive into USB1 port or insert SD Card to SD Card
slot on the projector.
2. Select the "Multimedia">>"USB Disk" or "SD card">>"Video", "Music"
or "Photo" to enter the file folder.
3. Select the file to play with the up and down arrow keys, and press
"OK" to confirm.
4. When playing media, press "OK" to see the menu, and select item by
the left and right keys.
5. Support format: video, audio, and image.
Power off:
1. Sleeping mode: press the power button and hear the “beep” sound
with the power button still blue.
2. Power off: hold the power button for 3 seconds till you hear the "beep”
sound twice, and the power button turns red.
2. Display mode: Swtich standard/ ECO/ bright mode.
3. Portrait mode: Switch on to project vertically. Please
make sure NOT to block the ventilation.
4. V.Keystone: Automatic vertical keystone adjustment
up to ±25 degrees.
5. H. Keystone: Manually adjust horizontal keystone up
to ±14 degrees.
6. 4 Corner Correction: Choose the corner to be adjusted
and use arrows to change the location.
7. Color Setting: Change brightness, Contrast, Saturation,
Sharpness, R/G/B Gain, and R/G/B Offset.
8. Firmware Upgrade: Upgrade via USB drive or through internet.
9. Projector Location: Change to Front/ Front Ceiling/ Rear/ Rear Ceiling
mode.
10. Language: Change language with arrows.
11. Reset All: Choose yes to reset projector to factory default. All saved
changes to Setting are lost.restored. The projector will be restored
to the factory settings, and the data adjusted by the user will not be
saved.
Settings
(V. Keystone)
(H. Keystone)
(4 Corner Correction)
Select the "Setting" key on the projector or remote control, and press
"OK" to confirm.
1. Wi-Fi setting : Select the "Wi-Fi setting" menu and enter the Wi-Fi
setting interface, select the "Internet", press "OK" key to confirm, and
select the router from AP list and enter the password.
How to Plug and Play (via USB cable)
Android
iOS
1. Select the Android on main menu of projector, and then select Plug
and Play menu by pressing "OK" key.
2. Connect your mobile to the projector via mobile USB data cable.
3. Download and install EZCast app from Google Play Store or scan the
QR code shown on screen.
4. Launch EZCast App and follow the guide. If the guide doesn’t pop out,
click at the upper right and click “+” at the upper left.
5. Press and scan the QRCode on your screen.
6. Make sure the SSID and picture shown are correct.
1. Select the iOS on main menu of projector, and then select Plug and
Play menu by pressing "OK" key.
2. Connect your mobile to the projector via mobile USB data cable, and
then choose "Trust This Computer" to start your projection.
Note: If there’s a black screen after connecting to mobile, please reboot
your mobile and then try again.
Windows
MacOS
1. Select Windows on main menu of projector, and then select Plug and
Play menu by pressing"OK" key.
2. Install EZCast app on your PC.
Please visit https://www.ezcast.com/app to download EZCast app.
3. Connect your PC to the projector via USB A-to-A cable.
4. Launch EZcast app on your PC and click icon.
5. Find and select "Beam-XXXX" from “Search device”, and click to
mirror.
1. Select MacOS on main menu of projector, and then select Plug and
Play menu by pressing "OK" key.
2. Install EZCast app on your PC.
Please visit https://www.ezcast.com/app to download EZCast app.
3. Connect your PC to the projector via USB A-to-A cable.
4. Launch EZcast app on your PC and click icon.
5. Find and select "Beam-XXXX" from “Search device”, and click to
mirror.
How to Wireless Display
Android
iOS
1. Select Android on main menu of projector, and then select Wireless
menu by pressing "OK" key.
2. Select mirroring function in the setting of your phone and
find”Beam-XXXX” device shown on device list to start your mirroring.
Note 1: The naming of mirroring function varies different brands.
Visit https://www.ezcast.com/usage/android/ezmirror for demos.
Note 2: Compatibility: Android 5.0 or above.
Note: Compatibility: iOS 12 or above.
1. Select iOS on main menu of projector, and then select Wireless menu
by pressing "OK" key.
2. Make sure both of your projector and mobile are connected to the
same WiFi router.
3. Go for Screen Mirroring of your mobile and select the ”Beam-XXXX”
shown on the list to start projection.
Table des matières
Autres manuels EZCast Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
