EZCast Beam J4 Manuel utilisateur
EZCast Beam J4 Quick Start Guide
This EZCast Beam J4 Quick Start Guide provides a
guideline for basic operation.Please read the guide
thoroughly before operating the projector.Please visit
www.EZCast.com for additional information.Product
information is subject to change without prior notice.
J4
Thank you for purchasing the EZCast Beam J4 DLP projector.
Our product combines the easy to use interface, portability, and
cross platform compatibility, to let you enjoy projecting media
from Android, iOS phones and tablets, and laptops, anytime,
anywhere.
EZCast app installation
Please visit www.EZCast.com/app to download EZCast app for
every supported platform.
Mobile devices can proceed to the relevant download area by
scanning the QR code below.
(iOS users can search for EZCast in the App Store to download
the app)
(Android users can search for EZCast in Google Play to
download the app)
Never look directly into the projector lens when the lamp is turned
on.The bright light can damage your eyes.Never let children look
into the lens when it is on.
1. Precautions
How to use the projector:
（1）Do not point the projector lens towards human eyes. The bright
light can cause damage to eyes.
（2）Do not block the air vents. Blocked ventilation may cause
overheating and damages to the projector electronics and
components.
（3）Do not use chemicals, detergents or water to clean the
projector. Moisture and chemicals may corrode the projector
circuit boards.
（4）Do not place the projector within reach of children.
（5）Only use the projector in dry environment with good ventilation.
（6）Do not store the projector in extremely hot or extremely cold
temperatures. Extreme heat and cold can reduce the
component lifetime of projector. Recommended working
environment is between 5℃~30℃.
（7）Do not attempt to dry the projector in heating devices, such as
dryer, microwave etc.
（8）Do not squeeze or apply excess pressure to the projector. The
projector may be damaged from the pressure.
（9）Do not throw, knock or shake the projector. The projector may
be damaged from the vibration.
（10）Do not attempt to open the projector. Please refer to qualified
customer support.
（11）Do not attempt to service the projector. Please refer to qualified
customer support in the event of projector malfunction.
3. EZCast Beam J4 body and remote
DC
Control Panel
Power
Reset
Focus Ring
USB
Headset Jack
Remote Sensor
HDMI Wireless Kit
Select Back
Arrows
Speaker
mode
Select
Back
Volume
up
Volume
down
Arrows
Power
Home
Settings
OK
Wireless
Adapter
HDMIDC
Preparation
How to set up EZCast Beam projector
1. Insert the wireless adapter into the wireless kit port of the
projector.
2. Plug the power to the projector, and the power button will
light up.
3. To turn on projector, hold the power button of the projector
for 3 seconds till the light turn green.
4. Adjust focus ring until the projection image is clear and
focused.
About portrait mode
The projector supports full-screen vertical videos
automatically when both the mobile and the projector are
displayed by portrait mode.
(1) Enter “Settings” and find “Image” settings.
(2) Switch “Portrait mode” option to “Auto”.
(3) Go “Keystone calibration” if needed.
(Landscape mode) (Portrait mode)
First time settings
1.Select the start-up language.
2. Wi-Fi setting: connect the projector to your router and enter
the password. (Important)
3. After starting up, enter the main menu and select the
functions by arrow keys on the projector or remote control:
Android, iOS, MacOS, Windows, bluetooth, EZCast, Multimedia,
HDMI, and Setting, as below shown:
Multimedia playback
1. Insert a USB flash drive into USB1 port on the projector.
2. Select the "Multimedia">>"USB Disk">>"Video", "Music" or
"Photo" to enter the file folder.
3. Select the file to play with the up and down arrow keys, and
press "OK" to confirm.
4. When playing media, press "OK" to see the menu, and select
item by the left and right keys.
5. Support format: video, audio, and image.
Power off:
Hold the power button for 3 seconds.
2. Display mode: Swtich ECO/ Standard/ Bright mode.
3. Portrait mode: Switch on to project vertically.
Pleasemake sure NOT to block the ventilation.
4. V.Keystone: Manually vertical keystone
adjustment up to ±30 degrees.
5. H. Keystone: Manually adjust horizontal
keystone up to ±14 degrees.
6. 4 Corner Correction: Choose the corner to be
adjusted and use arrows to change the location.
7. Color Setting: Change brightness, Contrast,
Saturation, Sharpness, R/G/B Gain, and
R/G/B Offset.
8. Firmware Upgrade: Upgrade via USB drive or through
internet.
9. Projector Location: Switch to Front/ Front Ceiling/ Rear/ Rear
Ceiling.
10. Language: Change language with arrows.
11. Reset All: Choose yes to reset projector to factory default.
All saved changes to Setting are lost. The projector will be
restored to the factory settings, and the data adjusted by the
user will not be saved.
Settings
(V. Keystone)
(H. Keystone)
(4 Corner Correction)
Select the "Setting" key on the projector or remote control, and
press "OK" to confirm.
1. Wi-Fi setting : Select the "Wi-Fi setting" menu and enter the
Wi-Fi setting interface, select the "Internet", press "OK" key to
confirm, and select the router from AP list and enter the
password.
How to Plug and Play (via USB cable)
Android
iOS
1. Select Android on main menu of the projector, and then
select Plug and Play by pressing "OK" key.
2. Connect your mobile to the projector via mobile USB data
cable.
3. Download and install MiraPlug app.
4. Replug the cable and it will start casting automatically.
1. Select the iOS on main menu of projector, and then select
Plug and Play menu by pressing "OK" key.
2. Connect your mobile to the projector via mobile USB data
cable, and then choose "Trust This Computer" to start your
projection.
Note: If there’s a black screen after connecting to mobile,
please reboot your mobile and then try again.
Windows
MacOS
1. Select Windows on main menu of projector, and then select
Plug and Play menu by pressing"OK" key.
2. Install EZCast app on your PC. Please visit https://www.ez-
cast.com/app to download EZCast app.
3. Connect your PC to the projector via USB A-to-A cable.
4. Launch EZcast app on your PC and click icon.
5. Find and select "Beam-XXXX" from “Search device”, and
click to mirror.
1. Select MacOS on main menu of projector, and then select
Plug and Play menu by pressing "OK" key.
2. Install EZCast app on your PC. Please visit https://www.ez-
cast.com/app to download EZCast app.
3. Connect your PC to the projector via USB A-to-A cable.
4. Launch EZcast app on your PC and click icon.
5. Find and select "Beam-XXXX" from “Search device”, and
click to mirror.
How to Wireless Display
Android
iOS
1. Select Android on main menu of projector, and then select
Wireless menu by pressing "OK" key.
2. Select mirroring function in the setting of your phone and
find”Beam-XXXX” device shown on device list to start mirroring.
Note 1: The naming of mirroring function varies different brands.
Visit https://www.ezcast.com/usage/android/ezmirror for demos.
Note 2: Compatibility: Android 8.0 or above.
Note: Compatibility: iOS 12 or above.
1. Select iOS on main menu of projector, and then select
Wireless menu by pressing "OK" key.
2. Make sure both of your projector and mobile are connected
to the same WiFi router.
3. Go for Screen Mirroring of your mobile and select device
name ”Beam-XXXX” shown on the list to start projection.
Table des matières
Langues :
Autres manuels EZCast Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
